Gasoline - Pump - Chevrolet - Corvette :: Starts But Stalls Out 20 - 30 Seconds Later
Apr 23, 2011
My car runs great except occasionally after I drive awhile, park and than restart to continue, it starts right up but stalls out 20-30 seconds later. I turns over but will not run. I have to let it sit for 30-45 minutes and than it starts up like a champ. I suspect fuel pump but would like an expert opinion. Garage says they can find nothing wrong and to bring it in when it happens... how do I do that.
View 1 Replies
Advertisement
2010 Cobalt, LS 2.2 Ecotec, with 13.7k miles. Oil level normal and battery voltage = 12.5V.
I've bought the car new in Feb. 2001. Car started and ran normally for the work commute on Friday, 9/2. Today the Cobalt starts normally, runs for 2-3 seconds, and then stalls. The accelerator has no effect. It's already been towed to the dealer..
View 1 Replies
My 88 "Rosie" has been having problems for months. It hesitates, stalls, and sometimes backfires. This is an intermittent problem, though it is happening more often lately. I took it to local auto shop and their computer showed Rosie was throwing a misfire code as well as a lean code. I took it 3 months ago, and I took it last week, got the same codes. The lean code led me to check the fuel pressure. I did and while it should be healthy 48-55 psi, I got 48 for awhile then 15 PSI! Now I'm thinking fuel delivery. I started with the filter. Sure enough it was dirty. Weeks later, the problem persists. I replaced the fuel regulator (ok, mostly because it was cheaper than the replacing the fuel pump, which I really didn't want to have to do.) Still, no luck, so I finally caved and spent $200 and 12 hrs dropping the tank to replace the fuel pump. Guess, what? Still no dice. I'm still getting the hesitation and the misfiring. I haven't put the fuel pressure tester back on it (been busy) so I don't know if the pressure is still low or if these other things are even related. I thought my logic was infallible. Let's face it, there's a finite number of parts that control fuel pressure. I'm running out of parts to replace. Where did I go wrong? The only thing I can think of that could still do it is perhaps the fuel pump relay? I dunno. Would it work off and on or fail completely? I'd love to get some opinions on this.
View 19 Replies
I replaced the fuel pump in my 2001 chevy blazer last year and it just quit again two days ago. Internet research leads me to believe it is a common problem in chevy turcks. Blazer stops running, sits for a few hours to a day and then starts up again. Is it going to happen again and is it really the fuel pump.
View 4 Replies
Car has 6600 miles on it and is back in the shop for 2nd time to determine what is wrong. Basically, the car starts and then stalls out after a few seconds. It will not start again (at least with me). Course, the dealer can get it started after the tow to them.It began in April after an oil change at the dealer. A week after the change, it started up and then a message SHUT DOWN appeared on the dash.
The car stalled and would not restart. When it was towed to the dealer, it had no oil. Per the dealer, there was no leak and it was assumed the tech forgot to put oil in it, They indicated it was not a problem since there was some oil remaining but the car would still not start. They kept it a few days and replaced the relay for the fuel modulator, electronic fuel pump, fuel unit, fuel pump control unit, e-control unit and of course the battery. Note: this was a cold start.
About a month later, I had driven the car for about 30 minutes, left it for an hour and came back to the car.....it stalled again right after start up and would not restart. After being on hold with roadside assistance for awhile, I tried it again and it started without issue. .
A week later (today), used it for a half hour, came back to use it 3 hours later and same story. Started, then stalled, no restart. Towed it to the dealer and the tech got it started but no codes telling him what is wrong.
View 5 Replies
I bought the car( like six months ago) there has always been a loud humming noise from the fuel pump ( I'm pretty sure it is the fuel pump anyways) not the normal whirring noise the fuel pump makes but a hum you can hear about ten feet away. Had no issues till just lately when the afternoons are well into a hundred degrees. That is when my car starts giving me issues. After one of these hot days on my ride home from work, I had just come off the highway and stopped at a stop light when I felt the engine bogging out, the engine stalled and I had to push it to the side of the road.
Its worth mentioning that this humming noise is much louder in the heat than the cool morning then when I turned the key to hear the fuel pump(auto fuel inject) it was louder than it has ever been, and would keep stalling on the way home, I had at the most a quarter tank of gas (gas boy is busted/stuck I think) the fuel pump is bad? Could it be the sock? I thought I read somewhere that my girl pump uses gas to cool down, and that having the tank any less than a quarter could lead to the fuel pump overheating????
View 3 Replies
I am working on my father's boss' 2004 Phaeton V8. The car usually sits on the weekends. What it is doing is, it will start and run smooth, but after 15 seconds, on the dot, it stalls and dies. It sounds like it is starving for fuel.
What I have done so far:
LH intake actuator arm found broken, replaced both with "Gruvenparts"
Checked all fuses and relays
LH fuel pump reads 14 volts until the relay kicks it off
Tested fuel pressure-good
Batteries fully charged
LH fuel pump reads 0.7 ohms w/key off
RH fuel pump reads 6.0 M-ohms when first connected and gradually climbs to 31.5 M-ohms
(I assumed this meant RH pump was bad and so I pulled it out and bench-tested. Ran perfect and tested at 0.7 ohms out of the car)
Re-assembled everything to pull the car out of the shop, and wouldn't you know it started and ran like normal.
Road-tested for 2 hours the next day without any problems.
So, I call the customer to pick it up and he says he will be there 2 days later.
View 15 Replies
One of my friends recently asked me to change the timing belt on his 2004 Passat 1.8T. I put on everything as instructed by the manual that the parts department gave me. However, when I start the engine, it runs perfectly for about three seconds, then starts rattling, and stalls out. I took the belt off and put it back on three times and yet, it still continues. This rattling seems to be coming somewhere from within the exhaust system near the engine and sounds like a back-fire. The check engine light also appears when this begins happening. I replaced everything, water pump, pully, tensioner, and etc. Note, I am a professional mechanic and have worked on several Volkswagen cars, including my own, but I never encountered a problem like this one.
View 7 Replies
I've got 200k on my Lariat. Engine was replaced 60k ago. It's in outstanding shape and is driven a lot. Suddenly this morning I start as usual and it runs about 5 seconds then stalls out. Every start, same thing. So it seems I am getting fuel pressure to start but it doesn't last.
I did replace the Fuel Pump Module within the past two years, due to corrosion of the FPM housing. At that time the truck would no start at all. Could it have gone bad already? I'm thinking this must be an electronics failure. It was perfect all day yesterday. 2004 Lariat 5.4...
View 14 Replies
The truck started acting up while driving. It would shut off (no miss or anything), but would start again. Now it is sitting in the driveway and wont run more than 3 seconds. The fuel pump has been changed and did not work. The fuel pump relay is new and did not work. I read that the fuel pump goes to another circuit after start up. Could it be running to start and then shutting off? Inertia switch is not tripped. Where to look next. 1992 Ranger 6 cylinder ....
View 10 Replies
My 2001 Prius (230,000 miles) is unusable. I can clear the codes. The engine will start up fine. After a few seconds it starts bucking and jerking as if the engine is trying to engage something that won't turn and finally stalls. It is similar to a manual transmission car's action if you fail to push the clutch in when you stop the car. What the engine is trying to engage? I don't have any scanner to read the codes.
View 7 Replies
I read the forums and found nothing quite like mine.
View 8 Replies
I have a 2003 ford explorer sohc 4.0l , that starts only with the gas peddle pushed to the floor and will only run for a couple of seconds at a time. Just replaced all the timing chains and tensioners. It has 145 lbs compression, and 60 psi fuel pressure. No codes on the computer.
View 8 Replies
I have an issue of fuel pressure I believe on my 2003 3.5 Santa fe...It would start then stall...I'm at my wits end with this thing...I checked the relay and its good...checked all fuses and they are good...I don't hear the 2-3 second whine of the pump when I turn the ignition to the on position, so I suspected a bad pump...but before I bought a new pump I took out the back seat, removed the access cover and checked the connector to see if the pump is getting power...its not...I'm at a loss as to where to look next...
View 35 Replies
I have a PS 6.0 in my '04F350 that starts very reliably but stalls within 1-2 seconds. Restarts after cranking for 5-30 seconds. This only occurs if the truck sits for more than 6 hours. The longer the truck sits, the longer it has to crank to restart. Also if the tank is full and the truck is parked pointing down hill this does not occur, if it is parked pointing up hill it occurs even with a full tank. Shows no codes. I've had several mechanics look at it and no one has been able to explain or propose a solution expect for wholesale replacement of parts. The symptoms indicate to me that air is getting into the fuel system but I'm not sure where to look.
View 10 Replies
I have been without my dub for over a month mk4 gti/golf awp motor 1.8t manual transmission and have ran multiple scans and replaced multiple parts. I am suffering from a no start condition, start and stall immediately, and have troubleshot many problems.
Most recent vcds scan results are: intermittent door module fault (not faulty, not implausible, "intermittent") (j386) Speed sensor implausible (g28) (already replaced with no change) open circuit or short b+ fuel level sensor fault.
I have had the driver side door taken apart on multiple occasions and found: no cracked joints on the pcm of the LOCK module (solder covered by brownish/gold sealant?) Two breaks, 1 in the ground and 1 in the hot wire between the chassis and the door and since applied electrical tape to the chafed part of the door wire harness. I have ran multiple scans since applying the tape with various results.
After applying a maintainer and verifying full charge on BRAND NEW BATTERY I ran scan with above codes.
I have in the last month replaced coolant temp sensor, fuel filter, fuel pump relay, above mentioned battery, and installed toggle switch to lock module micro-switch, speed sensor. About 5-10k miles ago I replaced the fuel pump with vemo brand from ecs tuning and fuel pump relay.
I have re "seated" and cleaned all terminals, below and on the battery as well as on the transmission, have "checked" the ground just in front of the ecu and removed enough parts to place my hands on it to check for a loose condition. Also checked ground on top of block next to coil packs. I've checked pillar a for chafing and the ground next to pillar A and the ground just below the CCM.
I have also taken a mallet and attempted to re create this door slamming condition by tapping everywhere around the door jam on the chassis and door with no change. Also with the door LOCK module removed, I have tapped on it to see if pump would prime, no change...........
After sitting in my recaro imitation cloth seat totally defeated I realized that the intermittent fault code was pointing the "integrated window motor/DOOR module" that was the only thing I hadn't attempted to "test" (originally thought window motor was only a window motor)
Verified continuity to the door module, and verified continuity to relay panel, fuel pump and lock module........... Also tapped on the DOOR module itself with no change.
Piece the whole door back together, slam the door and bam fuel pump primes........... (also massaged the repaired-chafed wires before and after re-installing back into door, with no change/prime.) After sitting a while sometimes it will prime by itself......(with any of the 3 fuel pump relays I have for this car)..
Replacing 1 fuel part after the other over the 4 years I've owned the car has temporarily resolve my issue, until now. (Also have tapped around gas tank/retainer ring on the pump to see if fuel level sensor fault was a culprit). I don't believe this to be the issue because I've netted this fault in the past and has never cause a no start condition or come back after clearing when replacing fuel related part.
After slamming the door I have noticed the pump primes in waves, like a hum hum hum instead of 1 solid hmmmmm and when the car DOES start (when the pump primes) the pump continues the hum hum hum condition before dying. (I have gone as far as a test drive and I rev the engine and put in gear but acts as if i have a bad clutch, all rpms, no horse power like it's slipping condition from a bad clutch
immo light goes off when key in on position, epc and check engine light are off after car STARTS when slamming the door. With key in on position hear a loud click under hood (relay station I'm certain) but the throttle body buzz's until the chime sounds with door open (have not tested this when it DOES prime.....)
View 5 Replies
I have a 2002 Chevy Cavalier that stalls ever time it is fueled at the pump. It then continues to stall. I have to pump the gas like the old days when we all had carburetors and repeat the action many times. It always starts eventually, but causes unnecessary anxiety so I always fill my car at a time I don't need to be anywhere in a timely manner. It was taken to the shop but they could not reproduce the stalling, as they did not have the information that it mostly happens at the when fueling. The gas cap can be taken off for a while and it starts okay. The rpm is low after adding gas, if you give it gas, it runs then eventually idles normally.
View 6 Replies
I have 1986 Gold Corvette, which now has Antique Virginia Plates. I had a terrible Vibration at 65 - 75 MPH that would shake the car so bad I could not drive it more than 20 minutes and I could not tell if it was in the front or the back.
I had the following installed: Front and Rear Wheel Bearing/Hub Assembly (Timken), Front and Rear Brake Rotors, Front and Rear Rebuilt Calipers, Front and Rear Hawk/ Wellman HPS Brake Pads and four Stainless Steel Brake Hoses.
Now the vibration is about half-gone, but still shakes the GoldVette at 65 - 75 MPH, and I still cannot tell if it is in the front or the back.
A few years ago, I replaced the Rack-in-pinion and Tie Rod Ends. What do I replace next to eliminate the vibration so that I can drive it about 100 miles?
View 15 Replies
so I was driving down the street the other day then my car completely shut off no interior lights car won't turn over radio wont turn on had to push it up the hill, to get it out of the street and get it towed.
View 13 Replies
I am having a couple issues with my 94 Corvette with Auto Transmission with 107k miles.. First, when I am coming to a stop, from like 2 mph to full stop, I am getting like a clunking that sounds and feels like it is coming from behind me and to the right (from rear middle of the car). It does Not do this if I shift into neutral b4 I get to low speeds.
The second problem is, I got caught in a very heavy rain last weekend, and the digital speedometer area started blinking off and on about once or twice per second, and the "idiot light" panel lit up like a Christmas tree. The car started sputtering but never stalled out...it was almost if it was turning itself off and on repeatedly. I pulled over under a canopy, and waited out the brief but intense downpour, and its been fine ever since (about 100 miles), but it has only been driven in nice weather since. I checked the battery connections (and that's about it) and they were tight and clean.
View 3 Replies
1981 Corvette rebuilt/restored. 35+ mph. steering wheel shakes/vibrates. Higher speed, depress clutch, smooth ride. Taken to mechanic recently, test driven to acknowledge, lift done twice, no clue.
View 5 Replies
