Ford - Ranger :: Stalling Out When Cold - Cylinder 4 Misfiring
Apr 3, 2011
I've got a 2000 Ford Ranger, manual 4 cyl. When cold, she's been stalling out. It happens very reliably when I come to a stop and put it in neutral (or put the clutch in). Only when she gets warmed up does it stop. Check engine light has been on (for a long time) saying the TPS sensor is out and the 4 cyl. is misfiring. I replaced the TPS sensor and it had no effect on the problem. A friend recommended changing the oxygen sensor.
View 5 Replies
Advertisement
This has been happening intermittently for a while now. The car has about 97k on it and I within the last 1000 miles have replace the timing belt, water pump, coolant temp sensor, tensioners, thermostat, and MAF (OEM BOSCH from ECS).
The car was overheating; all the cooling/timing related stuff was changed, no issues for a few weeks. Then it started misfiring and stalling like a madman in cyls 2 and 3. Ran ran if for the code pulled the MAF and sure enough it looks like the PO never cleaned it as there were probably 2mm of buildup on it; as preventative maintenance I went ahead and just replaced it completely.
Now, less than a week after I replaced the MAF the car will make random little popping noises under hard acceleration, and randomly will just completely stall; without showing the battery or check engine lights, similar to how it was stalling right before the MAF went bad. I live three miles from my office and it has happened going to and from every day for the past two weeks.
As far as I know the car is mostly stock (I purchased in in March). However it does have a knockoff BPV of some sort that I think could be causing the issue as the popping noise sounds like its coming from the passenger side of the car. What this might be (if it's not the BPV).
View 10 Replies
Had a misfire in cylinder 1 so I put new plugs and wires. Still misfired. Changed fuel injector. Still misfired. Changed ignition coil and misfire on cylinder 1 is gone now cylinder 2 and 3 are misfiring. I double checked wires and they are properly installed.
View 11 Replies
I got this 98 Ranger 2.5 that I've done a tune-up on less than 30,000 miles ago. I changed plugs, wires, and both coil packs. Timing belt, thermostat, fuel pump, fuel injectors are all recently changed too within a year or two. Fuel filter and air filter I change every 30,000 miles. The truck runs as great as a 4 Cylinder will run. It's at 344,000 miles but the engine was changed once so it probably has over 100,000 miles on it. There is just a slight miss you can hear through the tailpipe but it's not severe enough to be picked up by the Check Engine Light. In fact, even when the coils were totally gone it never put up the Check Engine Light. I can tell when a coil pack is going out on this because it's done it several times so I usually just change them with the tune-up. It's only a slight miss some people may not even notice it. I was just wondering is there any way to track down where the miss is? I tried looking under the hood in the pitch black and there's no plug arcing.
View 1 Replies
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 Replies
1998 4.0 ... She only misses about 30 seconds during stone cold startup. I figure it's probably the plug thats hardest to reach ? Isn't that the way it always is? From the hood I can see only one spark plug, so I figure I'll do all the plugs. Is there any right or wrong approach to the plugs? I did the thermostat today, but this plug job looks like it's gonna be a bitch. Time for some skinned knuckles Next is the right side O2 sensor, that looks like fun too. But I gotta say, this little truck is sweet. Great visibility and easy to park in the city. I really like her. She's a keeper. She needs some new sway bar bushings too, but no surprise with 127 K on the clock.
View 5 Replies
I have a 2001 Ford Mustang, V6, 3.8 Liters, automatic transmission, 120,000 miles. Recently, my car has started to stall/misfire at when I come to a full stop at a red light. It feels like the car is going to shut down and like it has no power. I have to press the gas really hard to get it to pick up power and speed. It doesn't happen every time and I've noticed that it happens less early in the morning or at night, and it happens more often during the day when it is really hot (I live in Az and temperatures are currently in the 100sF).
The "service engine" light is not turning on. The battery was checked and it's fine (recently replaced in September 2011). The alternator was changed 1 month ago. The cooling fan was replaced 1 month ago. I took it the the Ford agency and no codes are turning up and they can't seem to duplicate the problem even though the ran the car for 15 miles. They checked coils, spark plugs, fuel injectors, fuel filter, gas pump pressure, and it all seems fine. They advised that I fill up my gas tank with Premium gas and add fuel injector cleaning fluid. I did and the problem is still there. They then advised to fill up gas tank again with Premium and add Techrnon additive. I did and the problem is still there.
I am scared that my car will stall and turn off while doing a left turn with oncoming traffic or in the freeway.
View 2 Replies
I recently bought a 05 f150 with 5.4 3v and 195k miles needing some work. Ran great, just had a code for timing over retarded. Originally it had a cracked timing cover, so i took it off to replace and found broken guides and bad tensioners on timing. I installed new guides, chains, and tensioners, and cleaned phasers, and put back together only to find it ran terrible and had a phaser rattle. I then went in and installed phaser locks, which took care rattle but not the running issues. I can not figure it out.
ISSUES: My issues almost mirror what is said in this thread here, but this issue was never solved. [URL] ....
My issue is when started cold it starts right up, idles ok, runs ok, although a bit sluggish. Once its warm it stalls at idle, shudders when giving throttle in overdrive, and if you kick it down it will continually backfire, and slowly accelerate... it kicks down but acts like its only getting 1/8 throttle, just kind of hangs at the same rpm and slowly climbs in rpm. Sometimes it wont backfire as much, and sometimes the check engine light flashes. After it stalls at idle and you start it back up it sounds like it shudders/backfires for a split second then starts.
It is throwing many engine codes, but most are from the phaser locks. Throws code for timing over advanced on each bank (phaser locks lock them fully advanced), cam timing codes for each bank, and then a code that doesn't have to do with the timing, P2106. I am going to run some live diagnostics on it today and report back but I am fully at a loss.
View 5 Replies
I have an 2006 f-150 King Ranch with 103k miles and it was misfiring and then stalling when stopping at lights. Both cam shaft sensors and all coil packs were relaced then it was still misfiring. The head was recently replaced and now they are waiting on a new computer. When it starts misfiring it vibrates the whole truck and the engine light flashes. If you turn the truck off then back on it will run fine for about 50 miles. Im worried that replacing the computer is not going to fix it, what else could it be?
View 14 Replies
Changed the spark plugs now I have misfire in cylinders 3 and 6. Do I change the spark plug wires or the coil pack?
View 5 Replies
Trucks throwing codes for cylinder 3 and 8 misfire. I pulled the plugs and both were covered in oil and cylinder 8s electrode was literally gone. so I replaced the plugs and within 5 miles it was missing again. so I replaced all plugs, all wires and coil packs. cylinder 8 plug had fouled out. Its a 4.6l 99. I have a mild exhaust leak where the manifold connects to the downpipe. but not bad enough I feel it should matter. it runs rough until about 3k rpm and then it kinda straightens out.
View 14 Replies
I had a misfire and my CEL came on had it read and it said cylinder 4 was misfiring and that there was a misfire in the first 1,000 RPM's. I replaced the COP and plug and now I'm getting terrible MPG. I tried to reset the PCM by removing the Neg. battery connection and it seemed to work for 4 days now my MPG has gone bad again. It seems to run smooth/good.
View 1 Replies
Had a miss in the #5 cylinder on a 2005 F-150 5.4 Triton. Had it hooked up to see which code was given and the tech said that #5 was the culprit. Taking no chances, I purchased a new plug and coil pack. I installed them and it ran great until I got up to around 70mph and then it started dong the same thing it was doing earlier. I took it back to the place that checked the codes and it came back as the #5 cylinder misfiring again. I am not sure how this is possible after replacing the plug and coil pack. Is there some way that the plug that fires just ahead of #5 is fouled out and causing the #5 cylinder to get too much fuel transferred to that cylinder? Or is there a possible short somewhere causing that cylinder to misfire and ruin the coil pack? I am stumped on this for the moment anyway.
View 8 Replies
2004 5.4L ... Codes indicate a firing issue on #4 cylinder, figure it's the coil pack. They bought truck used a few years ago and plugs have not been changed since they have owned it. I was going to change plugs while I was under the hood. While checking threads on this engine I picked up on plugs being a major job unless you know the tricks. So what tricks do y'all have up your sleeve to keep from breaking plugs?
View 14 Replies
i have a 2005 f150 4x4 5.4 3 valve. it ides good but when it is in on it splutters, and also feels like dead cylinders in passenger gear. i checked the codes the other day and i had a cylinder 5 misfire. so i cleared it and today checked again and had running lean bank one and cylinder 8 misfire, then checked one more time and had cylinder 7 misfire. I am sure it is a bad coil but how do I know which one?
View 2 Replies
I have a 1996 ford taurus lx v6 3.0 dohm..my check engine light flashing. then it stop flashing..i did replace spark plug,wires,coil pack..when it start to flash i put it gear the car start to shake and sputter.i really don't know why its doing that the car has about 150000 miles on it..i do get a code p0302 Cylinder #2 Misfire..the new plugs and wires and coil pack is about 2 weeks old..
View 11 Replies
I've had a 1991 buick skylark for 3 years, just hit 100,000 miles, and for the past few months i've been having problems with it stalling out/misfiring when I press the gas, almost like a lawnmower running out of gas, and then catch and go fine. it was only happening at the 3rd gear change,(randomly but only at that change), and then it started happening only at the 2nd gear change. it first happened at the end of a long road trip, and the speedometer and odometer stopped working at the same as well, but have since returned. but now it's been happening on cross town trips.
Every time it has happened has been random, and it always corrected itself and was fine. but this last time, it was doing it consistently, at random gear changes and from idle. it finally gave out at a stop sign and it barely stuttered across the intersection, but with the check engine light on and never "catching on" or actually dying/cutting off. I took it to my local shop, and they ran all the computer test and road tested it and told me they couldn't find anything wrong. they tested the fuel pump, which had good pressure. They mentioned it might be the module, but were honest and didn't want to charge me for something they couldn't tell was actually wrong. any clue?
View 2 Replies
Happened a few times on me lately. While pulling towards the top of 5th, I'll start to see the check engine light briefly blink as if the car wasn't sure, then at the top of 5th, she'll start misfiring on cyl 2 and 5. It's only during the long haul pulls that this occurs. My plugs and coils were all changed about 1k miles ago.
View 17 Replies
Ok I got this truck from my mother-in-law for free with a blown head gasket cylinder 6 driver side. I did the replacement had the heads machined put it all back together by the book. Now I can't get it to fire on all 6 cylinders only 5 I think. Thought maybe bad gas (it sat since late November) put 5 gallons (over double the gas) fresh gas and half a bottle of b-12 chem tool. Dubble checked all plugs wires connections (coils plugs wires all new). I drove for about 10 miles oil pressure and temperature stayed perfect but no change in running truck shakes a lot and no real power. Don't sputter or backfire no engine codes other than imcr bank 2 open. Engine is 4.2l v-6 170k miles.
View 2 Replies
My 06 Elantra started to stall / misfire when I was driving it. It doesn't seem to matter how fast I am traveling as it will " misfire" for lack of a better word. It has an automatic transmission, and the rpm's will start to bounce as the car begins to jerk when this occurs.
I don't live anywhere near a dealership, so I brought it to the garage that I take my other vehicles to, and they had a hard time diagnosing the problem due to the fact that there never was an error code coming up or check engine light. They ended up finding a bad coil and changed it out.
That was 2 months ago and I haven't had a problem with it till today when the exact same issues resurfaced. And again no check engine light comes up, just the misfiring and when stopped at intersections, subsequent stalling.
View 8 Replies
Going up a hill this LS started shuddering and misfiring and set the po302 code. A small push on the accelerator sometimes seems to temporarily remedy the issue. This started about a week ago. fuel mileage : 26 mpg highway
Here's the readings I got at idle:
Fuel pressure is KOEO - 0 (That's what it read.); KOER - 30.
MAF - about 70
LT FUEL TRIM 1 - 5.5
ST FUEL TRIM 1 - STAYS NEGATIVE
LT FUEL TRIM 2 - STAYS NEGATIVE
ST FUEL TRIM 2 - STAYS NEGATIVE
ST FUEL TRIM 11 - STAYS NEGATIVE
ST FUEL TRIM 21 - STAYS NEGATIVE
O2 1 - NORMAL FLUCTUATES PROPERLY
O2 S12 - STAYS ABOVE .500
O2 S21 - NORMAL FLUCTUATES PROPERLY
O2 S22 - STAYS ABOVE .500
Not familiar with this vehicle...
View 2 Replies
