I had the universal joints replaced on my 1999 Ford Ranger now it vibrates badly starting at 45 mph and when I coast at 65 mph the vibration is very significant. The mechanic does not know what is causing this. I never had this problem before changing the U-Joints and I have 171,000 miles on the truck.
View 4 Replies2007 XLS Crew Cab 2wd. 60K miles When going through the 35 to 60 mile per hour range there is a vibration that seems to come from the drive shaft. Let off the gas and it goes away. After 60 mph it seems to be gone. I am thinking Trans support, motor support? One of the postings on this sight made me wonder about the transmission. By the way, I just bought this truck used and love it. Can I run flex fuel in the 4.6L engine?
View 1 RepliesI purchased a 1990 Ranger 4x4 with a v6 from auction. Took it to local shop to have them check it for me. Found out that it has a 3.0 in it and mechanic believes it is from a taurus. Truck actually runs extremely well. Has a few codes due to the ECM is for an automatic trans. Now the problem. I was on the highway-in 5th gear. Terrible noise the nothing. When I got it pulled over. The drive shaft was hanging from the rear end. It had been twisted like a straw. The transmission side had the yoke only, and the tail housing was cracked. It rolls and the drive shaft at the rear end turns. I figured the trans locked up. I don't know what trans to look for---is a 90 2.9 5 speed the same on a 3.0 ??
View 6 RepliesI have a vibration starting at 60mph. Its slight but there. I crawled under and found a very shiny rectangle of metal. Safe to assume I flung a shaft weight? It drives perfect around town just at freeway speeds.
View 14 RepliesI am driving a 95 ranger xlt extended cab with a 3.0 two wheel drive with an automatic transmission. the two piece drive shaft with the carrier bearing went bad at the bearing. i separate the u-joint just after the bearing and was going to remove the nut holding the bearing housing together but cannot get the nut off. now i'm also finding out that i need a bearing puller to remove the damaged bearing from the 1st drive shaft.
Its turning into something i may not be able to finish. i saw on line an idea where a guy replaced the 2 piece shaft with a one piece. he states that a 1 piece drive shaft, 1998 or newer would work and no need for this bearing. you have to remove the cross member. it sound easier than what i'm trying to do. i looked at some old posts and galleries but did not see an article. here is a link to his website: How-To: Swapping a 2-Piece Drive Shaft for a 1-Piece in a 1983-1997 Ford Ranger
I just bought a 5speed manual 2004 ford ranger 4x4 and when shifting usually upshiffter 1-2-3 I get a mi8ld clunk when I looked underneath I grabbed and can move the from drive shaft clockwise about 1/4 inch is this normal and if not how do I fix this?
View 3 RepliesSo I drive a 2003 VW Touareg....and the other day while driving, felt this strange vibration when accelerating over 10mph. The dealership said it was an $1800 repair and diagnosed it as the drive shaft.
View 2 RepliesToday I took the bed off of my 99 ranger. I was sitting on the cab looking down at the rear axle noticed the drive shaft was not entering the rear diff perfectly straight. As I looked further into it, I noticed the distance between the rear spring on the passenger side tire, is noticeably different. To visualize it, the wheel, at the bumper side of the axle, has a shorter distance between it and the leafs than the cab side. Not massive, but a few inches, and it's noticeable now that I can stand over it. I'm beginning to be very annoyed by this truck and it's previous owners, whom I take it , scammed my brother quite well with a $5k tag for a truck with so much not right with it. It's about to become my yard art for awhile.
View 8 Replies2001 Jimmy 4wd, 115,000 miles; Recently I noticed a strong vibration when in 4WD, no vibration in 2wd. I found that the rear joint (at the transfer case) of the front drive shaft has play in it. I am assuming that this is the problem. It has the appearance of a CV joint. Is that joint rebuildable or do I need to replace the shaft?
View 1 RepliesI was using the method of spraying starter fluid around the intake and found a pretty significant vacuum leak around the throttle shaft on the drivers side. The carb is a 2 barrel holley. What are some different ways to seal a throttle shaft vacuum leak? Could I take it apart and seal it with a plastic O-ring for now?
View 2 RepliesIn my 98 Ford Ranger, 4 cyl. manual, was driving up a 6% grade on the freeway, about 60mph for about ten minutes when i reached the top and began on a downhill grade. i let off the gas and put it in neutral to coast and then i looked down and it had stalled in neutral. i put it in gear to jump start it, it wouldn't fire back up. so i pulled to the shoulder. it wouldn't key start either. towed to mechanic, code read cam sensor. he also did a comp test and # 2 and 3 cyl were lacking comp. so the mechanic thinks the lack of comp is more serious than just the cam sensor, he thinks it might be the head. so my question is, can the cam sensor get far enough out of time so there would be no comp?
View 19 RepliesI recently replaced the oil seal on the front differential where the front drive shaft connects to the diff. I believe it is called the pinion oil seal. I had to remove the drive shaft to do the job. Got the oil seal in place and then slipped the u-joint yoke on and hand threaded the retainer nut on to get it started. I did mark the relative position of the drive shaft to the front yoke and the rear yoke. I had previously noted that the retaining nut, before I took it off had about 2.5 threads showing. I had to remove it with an impact wrench.
So...I used the impact wrench to put it back on with about the same number of threads showing. I then reinstalled the little short fronmt drive shaft...the one that comes out of the transfer case. I got the front of it on to the pinion output on the front diff...and then had to reattach it to the transfer case end which, by the way an interesting affair with a sort of metal cone that is attached by 6 8mm fine threaded bolts about 2.5 or 3 inches long. Got all that done with much grunting an groaning - I'm laying on the ground - SO the oil, leak is fixed but now ...
There is a vibration at around 40 mph and higher. like something is out of balance. did i damage the front diff pinion bearing by using an impact wrench? this vibration occurs in 2 wheel drive. as i understand it the front drive shaft doesn't even turn when in 2 wheel drive. my question is does the front diff gears spin when in 2 wheel drive? perhaps the u-joint is bad on the front drive shaft? just a bit baffled. when the speed drops to below 40mph the vibration goes away...
I have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 RepliesWe have a 2012 Nissan Altima. There have been 3 times that it would not start -all times were after a long drive and a trip to the coast! Battery is fine. Nissan dealership could find nothing wrong. Why this is happening ? Is it possible this is a censor /salt problem?
View 4 RepliesOk so my transmission feels loose, too much play between the coast and drive side of the gears. Makes enough noise now that my wife complained about it so I'm looking into taking it to the dealer. I pretty much expect them to pass this off and do nothing, but its getting worse especially in the last couple of months.
Noticed a lot of play in there gearbox? Can you hear the gears make noise as they shift from coast to drive side?
My 2005 chevy silverado 1/2 ton seems to be low a quart of coolant every 2-3 months. First alerted to this during a oil change, check it monthly and need to add a little to the reservoir every other month. The temp gauge never goes over half way. I do smell antifreeze after I shut the truck down after a significant drive, but only if I walk to the front of the vehicle.
View 6 RepliesEngine vibration? Its pretty significant and is always present doesn't matter if your in park or driving. What to check...
View 5 RepliesOwned my 2009 for 6 months now. Ever since purchasing it, car will vibrate significantly at highway speeds when first driving it, then decrease by 90% after a few miles. At first, since I purchased in winter, thought it was cold flat spots on tires. Dealer changed tires 3 times, finally with a new set of Turanza OEM tires. Still does it.
Service manager said he drove new 460's and they all do the same thing for a few miles. I have seen other comments on internet from other owners who report the same phenomenon. Don't think it is the tires since we went through 3 sets and it still does it in the summer. What else could cause a vibration until the car is warmed up?
I am wanting to remove my front drive shaft from my 2004 Aviator for a couple of month's while I save money to have my transfer case replaced. Are there any safety concerns with this? just need a couple of month's to get the money together....
View 5 RepliesI am doing some work on the truck and need to get the front drive shaft to drop down, I have the four bolts out but I can not get it to move. What am I not doing?
View 3 RepliesI recently moved to Pittsburgh where I constantly use my parking brake from Rochester, NY where I rarely ever used it. After I've moved to Pittsburgh (7 months after I've owned this 2004 Subaru Forester). After I drive for a significant amount of time (30+ minutes) and come off the freeway and stop or even slow down, the cabin of the car has a distinct, but faint burning smell. I am wondering if this could be the parking brake rubbing just slightly and when I slow down the smell stays in the cabin or if it is possible that the brakes are smelling (or something entirely different). Keep in mind that the smell doesn't happen when I only take a short drive, which is often. And of course, no I haven't taken this into an auto mechanic yet.
View 9 Replies