99 Ford Ranger disguised as Mazda B2500. (Same vehicle I think) 5 speed manual, 4 cyl., no a/c. Bought new and maintained according to schedule. Randomly fails to start. Cranks but won't turn over. I try several hours later and am able to start it. Mechanic has not been able to duplicate the failure to start. Checked thoroughly and finds no problem. I am very hesitant to drive it like this.
View 6 RepliesRemoving fuel injectors-coolant contamination.. How is this done? I need to see if they are any good-or clean/replace them-after I accidentally left the clip off the hose running out of the thermostat housing when I drained my coolant last week and the first time I drove, coolant leaked onto the top of the engine/manifold depressions, getting onto and into the fuel injectors.
I tried to clean it up as much as possible the first time(finally got it going) but still a few days later the truck at times cranks but does not start-hot or cold. I assume my idiocy is the cause or maybe it is just coincidence of something else? From what I read from my symptoms it could also be the fuel pump relay, pressure regulator, coolant temp sensor, crank sensor.. among other things. My fuel pump is 1.5 years old, so hopefully that isnt it. Have the injectors possibly been contaminated to where I should just replace them?
I have a 2002 F250 7.3L and it wont start. Its been sitting for the past few days in the cold because the batteries were shot but was plugged in the whole time. I replaced the batteries today and even poured diesel 911 5 hours before trying to start it in case the fuel was gelled. It cranks fine but just wont turn over.
View 2 RepliesThe truck just won't turn over makes a rrrgh rrrgh noice like it wants to start, I push the gas peddle to the floor and I should smell a lot of gas but don't!!! I added oil when it died at the store last night and it started up but the oil stick indicates oil is fine??? Pulled the diode out this morning put it back in the truck would not start just made that noise but turned it off and reseated the diode and it started??? These things may or may not have anything to do with the problem. Could it be electrical or oil pressure gauge sticking or something else that I could tell my mechanic and he could fix so I don't get stuck????
View 14 Replies85 2.0L Dura Ranger.
All of the Idle control wiring and box and sensors have been removed; all else is original. The truck ran just fine after the removal of the above paraphernalia (years). The truck simply quit, no spark at the coil, cranks just fine. All of the wiring has been checked for continuity. The Following components have been replaced with new:
Ignition switch.
Coil.
Dura-spark Box.
Dist coil.
Starter solenoid.
Rotor & Cap.
Plugs and wires.
Correct voltage is present at the coil & D-spark box side of the connector.
Coil tests close to what I think is correct for resistance and the engine ran with it.
I have tested both sides of every connector. I'm not sure what the output side of the D-Spark box (blue tab) voltages should be, and I am unable to test the trigger signal at the coil, however with no output and power in I'm guessing that is the problem...
I have a 1990 honda civic dx. with only 115,000 miles. For the most part it runs great, but for the past year it has given me problems when I try to start it. What happens is that at random times, it just cranks, but it doesn't start. Sometimes, if I try it several times (as much as 20 attempts) it will eventually start. Sometimes I have to leave the car for some time (10 minutes up to a few hours) and then it will start. I checked the spark, when it doesn't start, and it has a good spark. This seems to happen mostly when it is hot, never at night. My mechanic changed the distributor and that did not solve the problem. The ECM gave 16 flashes. My mechanic is frustrated in dealing with this because often it starts right up.
View 6 RepliesI just went to try and go pick up some dinner for my wife and I, hopped in the truck, key in the ignition, turn the key, let the computer go through the welcome screen, saw a very brief unknown image then main screen image. Turn over the truck and it just cranks. While cranking, it gives me a tpms failure, a service advance trac an engine overheat(even though it was roughly 24hrs since it last ran), and the wrench, of which those are what I remember but not necessarily in that order. I tried to plug in my dash boss to pull the codes, but no dice. I guess I an just curious what I might be looking at.
Background on the truck: 2012 screw with eco boost, 42,000mi, ford esp, and 99% trouble free.
My 2002 F-250 v-10 sat for over a month with me in the hospital for spinal reconstructive surgery. Battery was dead but has been charged and tested as good. The truck cranks strong but will not turnover. I am unable to do other diagnosis, what might be the problem.
View 2 RepliesMy 2001 Ranger is used for work to move furniture multiple times in a day. 7 weeks ago, I had moved a dryer w/ it, drove across town for a meeting, got back in & it refused to start & run. The same thing happened 3 days ago on a longer, fuller route w/ a trailer attached. Both times, the truck started & drove home ok AFTER sitting off waiting for my emergency ride. While I waited, I looked up the issue in the owners manual which told me to depress the gas pedal 1/3 to 1/2 & then turn the key in ignition. The first attempt did not work, so I repeated the steps, which started the truck & I was able to drive back. Both times, the truck started no problem the next workday. Does this sound like a problem worth fixing (for the age of the truck vs. cost of repair)? It has pull some weight, including on trailer, in between the two occasions.
View 1 RepliesNot all the time, but I've noticed it after the truck has been driven - shut off - then started again within a few min period. When truck is cold or has been sitting for an extended it starts no problem. By "delayed" I mean once I try to start the truck it takes a sec or two longer than normal before it cranks. Then when it does start it will idle very low for a sec or two then pick up and act normal.
So far I've done this to remedy it:
- new fuel filter
- new air filter
- cleaned MAF sensor
- cleaned throttle body
- seafoam thru vac hose
Only thing else I suspect is weak fuel pump but looks like it was act up all the time not just when the truck is started back to back. Truck has good power when running, I did a couple short blasts up to 80mph and everything was fine.
My 1994 Nissan Pathfinder will intermittently not start. When I get in the car and turn the ignition, the dash board lights will light up as usual, I can hear the starter solenoid click, but then nothing will happen. The power windows, stereo, headlights and air-conditioning will all work but the motor will not even churn. All I hear is the click. If I get a jump the car will start right up.
This has been going on for over a year. At first it would only happen every few months and I thought that by just disconnecting the positive from the battery and putting it back then it would start. It appeared to be doing so. When it started happening more frequently, I took it my mechanic and each time he would fuss with some wires charge me 20 bucks or not charge me at all and I would be on my way. It would be good for a week or so then once again not starting for me.
After the three times of my regular mechanic not fixing the problem and saying it was fixed I took it to a different mechanic. This man said it was my starter even though it will start with a breeze if you jump it. I went ahead and had him replace it. My car started a few more times but the next day the problem was back. After having gone to two mechanics and them misdiagnosing and me paying for service I didn't need, I borrowed a volt meter and the battery test at 11.5 volts. Some buddies said, that perhaps my battery being 14 years old was putting out enough power to power the cars electronics but not enough to turn the starter over. So I bought a brand new battery. I got four starts off of it before I experienced the problem again.
Another friend thought it might be the alternator not fully charging the battery. I believe we tested it at 12 volts but he said it should be more. Anyway, he and I pulled the alternator took it to be tested and it's fine. While we were removing it though we discovered the belt on the alternator was a little loose so maybe it wasn't charging fully. Anyway, we put it all back together and the car started five or six times, while my more knowledgeable buddy was with me. The next day of course, no start.
I probably did a bunch of stuff I didn't have to do in trying to diagnose this problem but at least I learned a lot more about my car. Anyway, ye wise car sages, What do you think is wrong with my old car, which for the most part has treated me well for all these years? Ignition? a short somewhere? If it's the ignition perhaps you can explain to me why the vehicle will start with a jump.
Been having an odd problem with getting my truck to start. Pass couple of days I've gotten out from work and gone to start the truck. It cranks just fine but wont start, acts like there is no gas. Let it for a minute or two and try again and it will start right up and keep running with no other problems. Go to leave for the work the next day and the same issue. Weird thing is the problem only seems to happen when its cold out 30F so or below. I was thinking fuel pump but I'm not sure. What to check?
Edit Its a 2002 Excursion XLT with the gas 5.4
Last night my boyfriend took a friend to the check cashing store, truck ran fine. shut it off, and when he came out the truck would not start. it cranks over but won't start. Took ignition coil off and had it tested but its fine. What else could be wrong or what can i do to try to get it to start again.
View 5 RepliesI just went out to move my truck to take out garbage and it cranks but doesn't start. It is 4.6L 4WD. I sprayed ether in intake no change. Checked all fuses all good. It has been raining pretty hard the last 3 days and it has been sitting in rain all 3 days. I checked for codes with a simple code scanner no codes. But the code scanner I used is not able to do KOEO or KOER tests. I know it needs new plugs but it has never sputtered or died on me. Has slight misfire but not engine stopping. I havnt had any check engine lights or problems before.
View 3 RepliesI have heard from a few people that it might be the computer that is messed up. Just replaced cap and rotor, spark plugs, wires, fuel filters. Pump turns on. Cranks and cranks but won't start. Took the intake cover off and tried starting it, all it did was back fire. Checked the firing order and everything is right. So im left with guessing at the computer and ignition??
View 5 RepliesOk, went out last night to go over to a buddies place to watch some football. Tried to start my truck but all that happened is that it would turn over, but not start. Had plenty of juice in the battery, and 1/2 tank of gas. It acted like it wanted to start, but nothing doing - just keeps cranking and cranking. Its even more frustrating because I was driving it around most of the day before this happened.
Here's the dillema: Its been doing this for the past two months now on and off. Once I fix something, it runs for about a month, and then it starts doing this again, without any warning signs (i.e. multiple cranks before a start, stalling, hesitation on accel., etc.). At this point I'm clueless. I've replaced the fuel filter, fuel pump, and air filter, but the problem has resurfaced again.
An interesting thing to note is that the only ways I'm able to get it started when it starts doing this is to remove the electrical connection from the intertia switch, and crank the engine a few times to relieve the fuel system pressure. After reconnecting the inertia switch, the truck starts instantly.
So whats the deal? Why this would work, and why suddenly the thing would not start after weeks and weeks of driving flawlessly? Is it possible that my system is either too pressurized or losing pressure somehow, and that is how it be able to start? A buddy suggested it might be injectors, but I'm not so sure, because there is no hesitation on accel or performance loss, or even a rough idle.
My 1999 Ranger that I bought used has been serving me well. However, two days ago I went to visit a friend and when I tried to start the truck to go home, the engine cranked but would not fire. I assumed that perhaps I had flooded the engine, so I walked home. I went back an hour later and the truck started up immediately. Then, yesterday, the truck would not fire at all. I towed it to AutoZone to check for error codes, but none were found. I put my inductive timing light on a plug wire and found that there was no spark.
In one instance of cranking, the timing light blinked and the engine tried to fire, but then nothing. The AutoZone man suggested changing the crankshaft and camshaft sensors. I haven't done that yet, but that is my next plan. Can the Ford dealer find error codes that tell what is preventing an engine from starting that AutoZone can't see? For sure there is no spark, but maybe there is no fuel either since I don't smell gas after much cranking. Could it be the inertia switch cutting off both fuel and spark?
This past weekend I noticed I was loosing boost pressure on my 2003 7.3l F250 so I pulled my turbo out found the problem fixed it then put the turbo back in. After it was all said and done I went to start the truck up and it just cranked and cranked a cranked but no start. Worried I didn't hook something up right I checked and rechecked everything to do with the turbo, all good nothing out of the ordinary.
I tried to start again, nothing. Spent all day yesterday trying to figure this out. Replaced the cps still nothing. No movement in tach but I don't remember any on startup anyway. Drained the fuel filter had adequate pressure and such but replaced the filter anyway. Still nothing. Checker all my fuses, one by on and non were blown but I still tried disconnecting my fuel bowl heater and still got nothing. I tried disconnecting the Icp still nothing. There was no oil around the icp either.
I'm getting frustrated that the truck wont start, the truck ran perfectly fine before the turbo removal but now wont even give a sign of kicking up. Just cranks and cranks. Also checked Hpop to see if that's the cause and it's filled like to the brim. But when I'm cranking the truck about 10 sec into the oil pressure gauge kicks up and reads good but only when cranking.
Truck cranks wont start. Fuses and relays good, New motorcraft; IPR, ICP with pigtails, New T500 hpop, New 180/80 Injectors, Push rods, 910 valve springs, Mellings lpop. Motorcraft oil cooler.
Reservoir full, oil new 15-40w Amsoil, Rails full, Fuel bowl full and clean, HPOP drive gear rechecked and torqued.
RPM 180
Temp oil 88*
ICP duty cycle koeo 14.8, crank 64.85
ICP pressure 250 -450psi
ICP voltage .27-.50
Manual gauge on oil rail 250 -450psi when cranking
Inj pulse width .0005,
Buzz test was good
Vref 5v all sensors. 12v at IPR w/koeo
Fuel pressure 58psi
Air test hpop hear no leaks with stethoscope.
DTC codes: P1280, P0380
Also put straight edge across injectors to double check they were seated.
2000 ford f150 4.6 auto. Will spin over but won't start. checked coil for fire, no fire. Check fuel rail for fuel, no fuel. No theft light flashing and no check engine light on. Has new battery and plenty of fuel in tank. Started fine yesterday but not today.
View 5 RepliesMy kid is using my 94 Ranger with 215,000 miles. It quit while he was on his way to work. Engine cranks but won't start.
Fuel pressure at rail was 12 psi (Key on eng. off). I replaced fuel pump. Pressure at rail up to 20 psi. Still cranks, no start.
I replaced fuel filter. Pressure at rail up to 30 psi. Still cranks, no start.
Replaced distributor cap/rotor and plugs. I have spark at plugs.
Chiltons from 1994 doesn't list a rail fuel pressure. I see new fuel pressure regulators are set at 41 psi. I pulled mine and hooked air to it. It (FPR) cracks at 37 psi. I have lots of flow returning to tank, so I assume the fuel system is working correctly. I've never replaced the timing chain/sprockets. Distributor rotor spins during engine cranking. When I rotate the crank pulley to 0 Top Dead Center the rotor is pointing to #1 on the distributor, so I don't think the timing chain has skipped a tooth on the sprocket??????