Ford - Ranger :: Hard To Start After Truck Has Been Parked Overnight
Sep 6, 2013
The problem is it is hard to start after the truck has been parked overnight. It turns over ok but seems to take a long time to start. After it has ran, restart is normal, it fires right up. My ranger is a 2001(4.0 liter V6) and the problem is also with my daughter's 2006 (3.6 liter V6). I have tried a new fuel filter but no change. If I turn the key to the on position without starting it for a few seconds and then try to start it the engine starts sooner but still a little longer than normal.
View 8 Replies
Advertisement
Recently, I have a weird issue on my car starting problem, 2005 I4. This happened after I replaced the upper engine mount (dog bone). When I left my car parked overnight and try to start in the morning, it makes a very slow start (Ruff Ruff noise). I have to tap on the gas a bit to get it starts. All the lights are still bright when I get to the car in the morning. The car has no issue at all when starts it during daytime or when I park car at work (about 8 hrs.). I checked and cleaned the ground terminals and make sure everything is tight.
View 2 Replies
My 03 Ranger 4.0L has become a mystery that has baffled every one I know. Everything was fine and I ran home to something from my house was in there maybe 10 minutes came out and the truck wouldn't start. it doesn't even crank over. out of the clear blue. I had a friend who works for a garage check it and he thinks timing chain. Since then I have been told it wouldn't just fall off sitting there with no indication at all there was a problem.
Thought maybe PATS system. Its in order. Put in on a computer from auto-zone and it shows a check engine light but the reading is there is no codes in the computer on file. I am at a loss. Its been months and I really cant afford to take it to a garage right now. Its the strangest thing ever no crank, no stalling just nothing I hit the switch it lights up like its ready to start and nada.
View 3 Replies
My 1990 4.0 refuses to start when the air temperature outside is at approx 40 degrees or below. It will crank until the battery runs dead if I let it. At approx 50 degrees farenheit the truck takes forever to start and always backfires out of the tailpipe and intake manifold (blowing off a hose on the vacuum tree) before it starts. If I can get it to backfire, it will start eventually. If it does not backfire, then I can run the battery dead and the truck still refuses to start. This condition has grown from a little problem to a huge problem over the past 6 months. Here is what I have done so far, including regular maintenance items.......
KOEO test checked OK
KOER test returned code 77 multiple times (TPS).
Replaced Throttle pos. sensor
Replace Idle air bypass valve
Subsequent KOER test came back with no more codes except 11 - OK
Load tested battery
Made new heavy gauge battery cables for + and -
New plugs, wires
newer starter
Changed coil pack for known good one off my explorer
Visually inspected hoses for vacuum leaks, replaced 1 cracked hose
1990 Ranger ext cab 4X2 4.0L, K&N air filter in stock airbox, Pacesetter headers, single 2 1/2" exhaust, stock cat no muffler, 260K on truck, 104K on good used engine from my 1994 Explorer. Purchased Ranger brand new in 1990. A4LD w/ shift kit.
View 14 Replies
My Santa Fe was really hard to start this morning..it seems when it rains overnight it seems to spin and spin and spin and take some time to start.. Could a low voltage battery be in cause ?
When it starts, i see no loss in performance or any CEL that's come up and runs like it always did before.
Any quick tests that could be done before i take it back to the dealer for a diagnosis ? I have a multimeter so i guess i could check my battery voltage to see if it's the source of my problem.
View 1 Replies
I've been suffering for this issue for quite a while. My passat 06 is experience a hard time to start up after sitting over night. The first attempt in the morning is always shaky. Then, it starts up okay during the day. Even like after driving 5 mins and I can restart it without any problem. But it's the first time of the day that troubles me.
And some history, my battery died completely like 2 months ago, and I replaced it with a Duracell. At first, it has no problem start up at all. But there was one day I forgot to turn of the lights and leaved my car over night.
The next morning, I was able to start it but with some difficulty. Since then, I have been experiencing hard times in starting up. Need to point out the issue? I'm really afraid to have a dead battery in a parking lot 1 hour away from my apartment again ..
View 11 Replies
Ok, so my 2007 F150 Lariat super crew cab has been at the dealership for a week now with them claiming that a part is on back order. How hard is it for them to get in a right front axle?? Granted, it was in there for other stuff too (which they can not give me a straight answer on if they fixed or not cause they are claiming the technician hasn't done the write up on it yet). My main concern is that they are screwing me around or that something happened to my truck. I am planning on stopping by there on Wed. morning after I get out of work.
Are these trucks known for bad front axles or was there some kind of a big recall on them?
Other things it went in for was the radio having the CD's cycle through when you first start up the truck, but does not happen like that all the time. Black plastic driver side front door hinge is cracked exposing the metal reinforcing part. Whirring/bearing type noise when you first start up the truck when it is cold and sits overnight (which they claim they can't hear yet waited to bring the truck inside and check it out at 3PM when they had the truck overnight from the night before when I dropped it off.) and the front driveshaft not fully disengaging when the truck is in 2wd. Almost seems like the vacuum locking hubs are still engaged.
View 8 Replies
My 2007 Civic Hybrid is having trouble starting. This happens when it's cold out, it's been sitting outside overnight (I don't have a garage), and the IMA battery is low. I've taken it to the dealership but they were not surprisingly no luck. The car has about 65,000 miles and a new battery - the one in front - was put in not too long ago and tests fine.
View 5 Replies
I just bought the truck and the previous owner said sometimes when the truck is parked in an angle, like in a drive way it will not start unless you use a screw driver and touch both posts on the solenoid. It happened to me today and I do not like it and need to find the cause? Why it would do this?
View 9 Replies
This is a 6.4L powerstroke, but this is not an engine specific problem. I have a no crank condition that appeared overnight while parked in the driveway. I CAN start it by using the solenoid connector wire near the air filter box and supplying 12v from + battery post. I THINK that eliminates batteries, solenoid and starter.
Now that leaves Trans range sensor or (NSS) and the ignition switch. I can test and get 12V (light) on the Blu/Wh wire from ign sw when turned to start, so that seems good. And as far as I can tell the trans range sensor is internal to the tranny, and I really don't want to go there if possible....
Also there are no codes on the Solus scanner I borrowed. And the voltage is showing as 11.7 on the scanner....is that low enough to prevent voltage from being sent to the solenoid thru the SJB and/or PCM even though engine will start as described?
View 14 Replies
My situation of hearing a clunk, clunk only when reversing the first time after the 2002 Camry was parked over night. The clunk clunk would not appear after the first reverse til the car was parked overnight and reversed the next day. I fixed this situation by only changing out both rear rotors, but diagnosing the problem was very frustrating as the symptom seemed to be only the rear wheels being stuck with the break pads and no connection with applying the breaks. Fortunately the problem was only with the rotors and not the differential or transmission or other expensive replacements.
View 3 Replies
1995 ranger. 132k miles. I have been having an intermittent starting problem. I replaced the battery which was 3+ years old. I thought that cured the issue because the truck started without a problem then, the same problem occurred. I started the truck and drove about 10 miles. Parked it for about 2 hrs. Went out and tries to start it. The engine cranked, but would not start.
Tried a second time and would not start.
I turned on the lights and proved the battery was good.
Tried to start it and it turned over.
I took it to a shop and they could not fine the problem.
I asked if it was a possible problem with the solenoid, alternator,
They said if it was those the engine would not turn and you would just hear a click.
They drove it for a week and it happened to their technician but he said he did not have his equipment to check it.
He got it started after a few tries as I did and got it back to the shop. Ran a scan.
Four codes returned that really did not identify the issue - P0231, P1701, P0340, P1270. They cleared the codes and drove it again. They checked the codes. It showed code P0340. The shop says the code states to replace the cam position sensor and installing an updated DPFE sensor.
I have been driving it for about a week on and the problem has not resurfaced yet. A friend whom I work with does some car maintenance told me it is a dead spot on the starter and to replace it.
View 14 Replies
I had parked my 2010 Prius in the garage overnight, the next morning it was completely dead. No lights on the dash. Nothing. I don't think I had left a door ajar or the lights on or anything. Can't be sure, though. So the car was dead, I called my Dad, (just like always) because he knows stuff, is an electrical engineer, even has his very own Prius. I thought it would be fun for him to charge it and we were a little afraid together (quality time!). We carefully followed the instructions in the book. Nothing went poof. The car started right away, everything worked fine. Off I went. I took my dad's portable charging thingy just in case.
View 14 Replies
I am having a problem with my O/D light flashing and my truck shifting hard. Just started out of the blue. After reading a few other topics, I am hoping it is the VSS. Now if only I could find the dang thing. Looking for a diagram, or detailed description on where it's at?
View 14 Replies
My gli has some trouble sometimes starting when parked upwards on a hill, I am thinking its the fuel pump..?
View 6 Replies
Got a 2004, Mazda 6i, 2.4LT, Manual, 140K miles
Car has been acting weird from past one week or 10 days. Outside temperature is around 25- 40 Fahrenheit.
I park my car in my home garage. It started fine in garage in morning, drove to work and parked in open parking lot for about 8 hours. Evening it did not start in the first try, it started at 4th time. I thought it might be weather and battery.
Next day morning it started fine in garage at 2nd start. Same problem in evening it would start at 4-5th time. Then I looked at my car battery and it was installed 2 years ago 3/2014.
I went to Walmart where my car battery was installed and they tested and said it is fine and has no problem with car battery. Just to make sure I took to nearby autozone they said that car battery is fine.
Over the weekend I left my car in our garage and was starting it every day morning to make sure if its working fine. It started fine and left it ON for about 45 minutes, everything is fine.
Today Sunday evening the weather outside was good around 55F. Went to some store for grocery shopping and returning back it started at 4th time.
When ignition key is turned ON, all the lights on dash board,radio,lights are fine and when I turn on the car it does not give any sound ( no cranking or anything) it was completely dead.Took the key out and waited for 5 minutes and tried again, with little cranking sound it started at 3rd try.
Took car to autozone for free testing and they said Car battery is good and when they asked me to start the car,it again did not start first time. They jump started my car and it started.
They are suspecting it might be alternator. What baffles me is why does the car start in 2nd try when parked in garage over night and does not start when parked outside in parking for about 45 minutes.
(Starter was replaced for the above car 2 years ago).
View 6 Replies
I have an '89 Ranger, Extended Cab, 2x4, 2.3l, Manual transmission with 255,000 on the odometer. I've owned it since 1990 and as far as I can remember it has either never had a clutch or only had one. I realize it's past due.
Everything has been fine up until this morning. 10 minutes after leaving the driveway this morning going a steady 55mph, no incline, it sounded almost as if I hit a deer. The truck jerked real hard, I put it back into 5th, and limped to my destination. Keep in mind for the next 30 or so miles there was absolutely no clutch slippage.
Here's the symptoms: No slippage, won't go into gears (I have to match rev's and shift without clutch, I drive a big rig and do this daily), when I do get it in 1st at a stop sign it wants to lurch with clutch all the way pushed down, I still have a great clutch pedal, and the most interesting thing to me is it sounds like something is being tossed around in my bell housing.
I'm almost 100% certain it's the clutch, however, I just wanted to come on here and report I have no slippage and it sounds like something being tossed around in the bell housing area. Is it possible a piece of the clutch could have "broke" off and that was what that huge jerk at 55 mph was? Approx. how much would a shop charge to put a clutch in on this model? I live in a rural area where prices are not inflated.
View 9 Replies
I have a 98 F150. The motor was replaced three months ago and have had no problems until now. The truck had trouble starting so i put an alternator on it. Fixed for a while and then it started blowing fuel relay fuses. I replaced fuel pump and filter. Truck has trouble starting after sitting overnight. When I am driving and floor it, once it hits about 4,000 rpms, the truck bucks like its the transmission but the rpms drop and then pick back up. Fuel pressure is right where its supposed to be.
View 1 Replies
Last night someone broke into my 2000 Ford Ranger (3.0L, automatic, 2wd, extended cab) and tried to steal it from my driveway. For some reason they didn't complete the theft. Looks like they forced open the rear sliding window to gain entry. The steering column is damaged where you insert the key. The rotating part where you insert the key that has a slit is laying on the floorboard, along with a plastic ring that has stranded wire around it. (I think this is part of the anti-theft system that senses the smart key).
Anyway, I can insert the key and turn the ignition but nothing happens, the engine doesn't crank. The "theft" lite on the dash is flashing more quickly than normal. The thief didn't damage anything else but did take the owners manual from the glovebox. This is just an everyday truck that is over 10 years old, nothing special about it, so I guess it was an attempted joyriding incident. Police said they had another vehicle in the area stolen and later found abandoned. I need this truck to drive to work, what do I need to do to be able to start it? There's not a lot of money in our budget for bigtime repairs right now.
View 6 Replies
I have a 95 Ranger with the 2.3L and it is a five speed. I am having a starting issue. I have replaced the ignition switch, clutch position switch, starter relay and had the starter tested. The truck will not start with the key. I can jump across the relay and it starts fine but will not even click with the key.
View 3 Replies
2002 4.6L 75K Miles ... Truck has hard time starting if it sits for a few days. Recently had the fuel filter (under driver's door) replaced for first time, and mechanic said it was clogged (?). He also checked fuel pump pressure and said it was good (about 40 lbs). Truck starts OK if used every day. Battery seems OK, as starter turn engine fine. Seems that there's a fuel problem.
View 4 Replies
