Ford - Ranger :: Hard To Shift Into Gear / Engine Clunk To Stop When Shut Off
Dec 21, 2012
This truck has been giving me tranny problems for a while now. About a year ago, stopped in traffic in neutral, I attempted to shift into 1st but it wouldn't go into gear, not reverse, not any gear. Eventually after a minute or so of trying it reluctantly went into 1st. About 6 months ago I started the truck after being parked and again it wouldn't get into gear. Shut it off, tried to get it into gear, nothing. Checked the hydraulic fluid reservoir for the clutch and it looked a little low so added a bit and after that it shifted into gear (maybe coincidentally). Now about a month ago, it again wouldn't shift into gear after being started. I checked the reservoir again, looked fine this time. Shut the car off, attempted to shift and this time shifted with ease
Something that I've noticed in the past year is that sometimes now when I shut the engine off it doesn't run down smoothly; kind of slows then clunks to a stop. Didn't used to do that.
View 2 Replies
Advertisement
My 2005 Impala will have from time to time a hard shift where there is a big clunk_usually 1st gear. I had it at a transmission shop last year and they could not find anything wrong. What is going on.
View 3 Replies
It's a 4 cylinder 5 speed, and once or twice a day when the light turns green and I go to put it in low gear, it just doesn't want to go into gear easy. It's like the syncro isn't happy or something. The clutch is depressed all the way and not dragging.
View 14 Replies
I have a 1999 ford ranger 4x4 with automatic 5r55e and it had problems shifting smoothly into third gear. I changes the valve body gaskets and the (rooster comb) detent lever. Now it shifts very hard and has on first second and passing gear.
View 6 Replies
2000 Ranger 4R44e transmission.Hard shift from 2-3 gear and when i run about 35-40 mph and brake then acelerate it downshifts hard . Whats wrong with it?
View 14 Replies
So, in my 99 Bounder RV (F53 chassis), V10
I think it has a 4R100 transmission in it (I have not verified this).
I had the oil and filter changed about 10K ago.
Runs and shifts fine .... then I stop and idle with it in gear (say stopped in traffic for a few minutes).
Now the thing shifts super hard! I actually get rubber in all gears.
So I pull over, shut it off. Restart the unit and everything is fine again.
It does this very consistently!
I went to the local transmission shop. They said with 110K in an RV it could be anything and I should think about letting them rebuild it.
Now that is something I would do ... not diagnose a problem and just rebuild it. I thought a "professional" would actually look for the problem first.
I don't want to rebuild the transmission if there is small item that will fix this.
View 3 Replies
I got new brakes pu ton lats month (semi-metalic). Any way I was driving to work and it was raining , roads were wet and my car was shifting weird after coming to a complete stop. once i went it would shift into first gear hard. I took it to a mechanic but he couldn't find a problem.
Then it was fine, no problem but today it was raining an dmy car did the same thing. Anytime I went when a light turned green or his the gas after being at a stop sign. the car would stutter as it shifted into first gear. like it would go , then act like it was stuck and then shift
It has only happened twice and its both been raining. Also my tires are really really bad.
Could it be the tires aren't gripping the road and that's why my cars shifting funny, like the tires aren't caught up?
View 8 Replies
Passat wagon, 2002, 1.8 T engine, 68,000 miles Auto transmission. When I start engine the two warning lights stay on, and then I shift into gear the engine jolts hard. I have parked it for now to learn more about what the problem may be. What is Anti-Slip Regulation and what does it mean when the indicator light stays on?
View 2 Replies
I just recently bought a 95 F150 with a 351. The truck has high mileage, about 190k, and I am not sure how long the transmission has left. It rides smooth down the road, but when I put the truck into reverse it hesitates for a moment then makes a loud clunking sound(as if a door is being slammed) and then jerks into gear. The reverse works great at the moment though. Should I be worried, is there anything I can do to fix this?
View 11 Replies
My surging/running down issue has returned on my '86 2.3l Ranger. I thought it was electrical, when things improved with the new ignition switch, but lately it's hard to get out of 2nd gear before the engine surges then starts to lose power. a poke of the gas pedal starts the who cycle over again. I pulled codes but it's hard to tell what the reader is saying either 33 and 34 or 334. The good thing is all the codes point to the EGR system. Looking for a diagnosis tree to determine if the valve is bad or the sensor is shot? They are both not cheap so I don't want to just throw parts at the problem.
View 14 Replies
I have been having an issue with my 4-5 gear shift under hard acceleration and know that a rebuild is due soon but I was wondering if any high performance kit available with all the clutches and friction discs needed to rebuild.
View 6 Replies
Could my brake issue be related to my transmission problem? Neither are constant. Brake problem= sometimes the brake pedal feels hard, like there's no power brakes (I drove a car once. ..looong time ago. .. that had no power brakes or steering) but it will kick in after a short distance. Transmission prob= seemingly unrelated, is a problem shifting from 1st to 2nd gear. This has happened maybe a 1/2 dozen times, the first time and mostly when in heavy commute traffic and when going between 1st and 2nd gear because of the slow commute speed, but also at other times when not in lengthy slow commutes. When it doesn't shift, the odometer doesn't work (shows only dashes) and an engine light comes on (the sprocket/gear looking one). Usually the transmission will eventually shift and the light goes off.
I read that the brake problem might be a vacuum hose problem? Something about a booster? Is this dangerous? or is it like having a car w/ no power brakes? Going to have my transmission looked at this week. Read on another site about dropping valve seats on this year car. If there's a major transmission problem, I'm wondering if it's worth fixing? I changed, timing belt, water pump, front and rears brakes, tires. 143,000 miles.
View 1 Replies
01 jetta vr6 5 speed. Alright so earlier today I pulled out the driveway. (Hard) was in 1st gear around 3 or 4 grand and I stomped it. Got to 6 grand and hit 2nd. Took 2nd to 6 grand and let of around 60 mph. After that I short shifted into 3rd, 4th, then 5th. I noticed going into fith was hard. Had kinda rev match to get it. I stayed in 5th till I got to my destination roughly 4 miles. When I came back out to leave I had a hell of a time getting it into reverse. On my way home it was extremely hard to shift and now when the car is running I cant get it into any gear. This is what I did.
Car shifts fine with car off.
Car will not shift with engine running.
When started in gear with clutch depressed I can still let the clutch out and stall the car.
When starting car while in gear with the clutch NOT DEPRESSED the car jumps forward.
I can figure it out ove tried re adjusting the linkage. Nothing.
View 6 Replies
I've been having this problem for about 2 weeks now, and I am trying to figure it out. I know the video is only 5 seconds but at least you can hear the sound, it only happens in first gear, on take off, about 2-5 seconds after the take off, and the sound is coming from the rear axle area. I cant figure out if its diff or brake related.
Ford ranger Rear end noise - YouTube ....
View 3 Replies
Ok so I'm having a problem that seems to have been getting worse. 1999 7.3, auto, 4 door, long bed, 6" lift. When I got the truck a while back I had a slight problem where if I was accelerating hard I would hear a clunk when it shifted into 3rd gear. I'm not hard on the truck that often so it took me a while to realize that the noise was the driveshaft hitting the floorboard right at the joint at the transfer case output.
The carrier bearing was flopping around a bit so I replaced that first. No better... kept driving the truck since it was only a problem while being really hard on it. But it's gotten worse so now when I tow (usually not more than 7-8k lbs) I have a bad vibration on takeoff at low speed. If I try to take off from a stop very hard with any load the driveshaft jumps into the floorboard. So I just replaced the transmission mount and checked the motor mounts, no better. Only thing I can figure at this point is axle wrap...?
View 14 Replies
2000 ranger 3.0 auto 4wd hard to shift. Are the cables known to stretch?
View 6 Replies
I have had my truck for about 4 years bought it used. I've replaced the motor due to #1 cylinder blowing up. So after I replaced the motor, it wouldn't start. Replaced O rings on HPOP (High Pressure Oil Pump) and started. When moving back to Colorado where I am stationed. It started getting harder and harder to start.
Then it got to the point where it wouldn't start so I would have to wait until I could start it or use a shot of starting fluid and yes I hate that. But I don't have a choice. I've bought new O rings replaced them and my IPR with upgraded screen. It fixed it for a week then the hard start came back. Tried unplugging ICP Sensor still hard start problem. ICP was reading 85%. When the truck is cold it fires right up no problems till it gets hot! Then driving down the high and hitting an off ramp it will shut off. When I try revers it will also shut off. The truck only has 111,252 miles.
View 14 Replies
My car has the clunk whenever I shift into gear (I have a manual) at low speeds and in low gears. Brought the car into the dealership and they think it's the front axles. Had one replaced (as they thought it was the passenger side axle) and clunk is still there. Went in to have the second one replaced, but part was not right. Waiting on the new part to arrive this week.
Axle? I honestly think it's tranny or gear related. Other than that, the car has been ok. I am going to work on sound deadening this week, getting my front strut bar installed and doing some research about the rear suspension.
View 8 Replies
I bought a 2003 Ford Ranger, 2.3, 5 speed manual. It is hard to shift after it warms up. I test drove it when it was below freezing, so I didn't notice it at first. The warmer the day and quicker the truck warms up, the worse it is. It goes into gear with no problem when the engine is off or if I'm still moving, but if I'm stopped there are times it is hard to get into gear. This really sounded like a clutch that wasn't fully disengaging to me, so I decided to pull it apart. I didn't check the movement at the slave before I started, but I did find the master was a little wet at the rod in the cab.
So, I did the following:
- New clutch master cylinder (system bled out of truck to eliminate air)
- New slave cylinder and bearing
- New pilot bearing
- Changed transmission fluid - Mercon III ATF
I inspected the clutch/pressure plate and it was in good shape and looked like it might have had 10K - 20K miles on it. The last owner said it was recently replaced and it looked it. So, I put it back in. After I was done, I checked the movement at the slave/pressure plate and it is moving about 3/8" - 1/2" when the pedal is down. I was happy and thought this would solve the problem since the old pilot bearing seemed stiff and I saw the leak on the back of the master cylinder.
I drove it and all felt fine at first, but it was a cool day and I didn't drive it that long. When it was warmer over the next couple of days, it started getting hard to shift again. It's not been quite as bad as before, but still doesn't shift right.
View 12 Replies
I have a 2002 ford ranger edge. swb, 3.0L, 5spd. I have been noticing it is getting harder to shift gears, put in 1st at a stop light lately. There is no grinding just seems harder to engage. Checked fluid level and it is clean and full. Recently i have developed a vibration under power. Let off the gas and smooth as can be, apply throttle and starts vibrating. Not sure if flywheel is "hot spotted" or perhaps broke a spring on pressure disk. Just seems odd it's only under throttle. Yes already checked rear end and U-joints.
View 2 Replies
My 97 Taurus shifts hard going into 2nd gear only. It started as just a cold problem but now does it all the time and there are no computer codes stored.
View 2 Replies
