Why can't ford use stailess steel sheet mental screws on the floor trim pice where door meets car. My 2010 Ranger the screws on taht trim piece have rusted already and I have drill them out and replaced them. In order to clean under the floor matting or remove trim piece. .
View 3 RepliesOK for the past few weeks I have been notice water on my floor boards on the DRIVER's SIDE. Now I just did some cab lights and thought ok maybe that's it. About a week ago while it was raining out I dropped the headliner and it was dry as a bone. So I eliminated that as a possibility.
Then I thought well maybe its my 3rd light and the water wasn't showing up until there. So that's been replaced and sealed tight. Now it has been cool here and has not rained in about a week now so everything should of dried out by now.
I left the floor mat out all of yesterday and last night and came out this morning to a dry floor area. I put the mat back in and drove the 15 minutes to my office and pulled the mat back out and the floor was wet again. I have not run my heat or A/C in 4-5 days and have not had any weather other then sun since last Saturday. The water shows up on the back of the floor mat more as like a heavy condensation then anything else. So my question is where is this water coming from?
Pulled out of street this morning and as I was shifting into 3rd my clutch pedal went straight to the floor boards. I was able to keep it in 2nd gear and get it back to my driveway . The pedal will only go straight to floor or goes straight up too the bottom of dash board. It's spring loaded. Am I dealing with a linkage issue?. I had clutch as I pulled out of my driveway and stopped go at the stop sign. Plus I was able to drive it back too my house with the pedal on the floor boards. Where I should look first?
View 4 RepliesFriday, 4/4/14: I have read many of the posts about this issue on this site. Didn't know this was such a widespread problem until I started doing my internet research today. Obviously there are many of us and this has been going on for a few years with this vehicle. I have had soaked floor boards twice and dealing with my third incident today(4 inches of rain last night). Have an appt with my GMC dealership on Monday. How I start this process with GMC to quickly get their attention. Obviously, I need to contact GMC first so that I can get their standard, worthless answer. But I've read I need to hire a "lemon law attorney", post my dissatisfaction on social media, contact the news media, etc. I am 62 yrs old, on disability, can't afford this inconvenience for something GMC should be RECALLING and fixing. Plus I have a small garage and this monster vehicle will not fit in it (didn't know that until after I bought it).
View 2 RepliesOnly had my 07 GS350 AWD for about a week now, and i kept hearing water sloshing around the floor boards. Did some searching on her and the interwebs and found the HVAC evaporator drain blockage TSB. So.... this was step one in getting it handled. I don't think its been wet for too long, only because there is zero musty smell or mildew. I yanked the front carpets back, and parked nose forward on my steep driveway, sopped up 5 full bath towels worth of water, cranked the heat and put fans on it. Boom, cleanup, done!
View 2 RepliesI have a 2003 Honda Pilot with 117,947 miles on it. When I reach 40 mph there is a shuttering sound that vibrates through the front floor boards. Took it to a Honda dealer and they could not duplicate the issue. It happened intermittently. Does not appear to be related to outside temperature or level of gas in tank. What the issue may be for the shuttering?
View 3 RepliesI can't believe how rusty my rear end is with 17000 miles? It's not flaking off rusty but it's not black anymore, is this bad ? I was thinking of painting it , but not sure if it's worth it????
View 12 RepliesI just bought a Lexus R350 2015. I didn't see the rusty from the trunk strut when I bought it. My question is the car is only 1 year old and the trunk strut rusty? Will the rust spread around other part of the car?
View 2 RepliesOk I got the brake pull fixed (I think) on my 92 Ranger 4x2 4.0 extended cab. I still will have to change the driver's side brake hose for prevention and the driver's side caliper just so everything will be new. But it stops straight now with a new brake job, pass caliper and hose on. However, this other problem has been ongoing and it does it on my 1998 Ranger too. It's not the heater core.
I think the evaporator case is filling with water and dripping down under the carpet. So the drain tube must be stopped or the case must have a bunch of leaves stopping it up. But where is this tube you're suppose to check? I don't see a conventional drain tube I only see a blower motor vent tube that doesn't drain to the outside of the car anywhere. I know my 73 Charger has a rubber drain tube that comes out of the evaporator case and drains onto the ground. But where is this one on a Ranger or what else could it be? It's only the passenger side so it's got to be that.
When we have a heavy rain water leaks in on both sides saturating the floor board.
View 2 Replies1997 Ford Ranger w/manual 5 speed tranny
A few weeks back my clutch pedal seemed a bit softer than usual one day. Still it worked fine... no problems shifting. Today after a short ride it went almost to the floor before disengaging. Now I cannot get it in gear without grinding.
So cold out I'm not sure I want to tackle this right now, what to look for and where?
I haven't ever been able to figure out why the middle of my passenger floor board gets wet when it rains or I go through a carwash. It's definitely not a heater core leaking. I don't see or feel any moisture under the seats further back or further up near the cowl, or roof. It's exactly in the middle of the passenger floor. Is there a plug under there? I've yet to pull back the carpet to look. I plan on eventually replacing the carpet but I want to figure out what the water is. It gets a musty smell because of the water. It's not a lot of water, not a puddle, just you can lift up the floor mat and see the moisture on it. So it's under the carpet. Windshield was replaced 3 or 4 years ago.
View 6 RepliesMy buddy called and said his clutch pedal went to the floor on his 04 4.0 ranger. Said no fluid leaks or anything, so I suspect the slave cylinder went. He said the slave is on the inside of the trans and you gotta pull the trans to do the slave, so might as well do the clutch too. How hard is it to replace both these on this truck? I've done it on a 94 cummins, so the trans should be a lot lighter. just wondering how bad of a job it is to do?
View 2 Replies1999 ranger 3.0, 5 speed stick. I was backing out of my driveway but there was a car coming so i pushed in the clutch and waited for the car to pass, when I let clutch pedal up off floor i heard a grinding noise, a little while latter did the same thing in first. Is this a first and reverse gear scyronizer or something else. What causes this and how to fix it ?
View 10 Replies1999 Ranger xlt, 4 cyl. 2wd reg cab, automatic. Getting a rumbling noise with some vibration in the floor ( nothing in the steering wheel, does not seem to affect handling ) runs consistently and relative to speed of vehicle......can not isolate or determine origin of noise.........
When initially driving car after sitting for awhile, the noise does not kick in until 50 to 100 yards have been traveled but is consistent thereafter,.....except for.. completely disappears during taking of left handed curves at good speed but reappears when road straightens...... right-hand turns have no affect positive or negative.
Have thrown into neutral at speed and sound and vibration is unaffected,.... brand new tires ( needed them ) with balancing had no affect either Struts, shocks, springs?
Installed a new clutch and slave today. Kept the same master cylinder.
The problem I am having is that the clutch pedal will not go to the floor, and therefore the truck won't start. The slave is moving back and forth roughly 3/8 inch, maybe more. I am pretty confident that there is no air in the system.
If I loosen the pressure plate a little, the clutch will go to the floor. But tighten it back up, and it again only goes down about 75%. This is a late '95 so it has the self adjusting clutch. I did get the correct kit for it, as well as slave. It's like the self adjusting part is too far adjusted and won't let my slave travel as far as needed.
In troubleshooting, I did notice that I failed to get the dowels in the flywheel aligned in the pressure plate. I am old school and not used to dowels in the flywheel! The dowels are not hitting anything and are not preventing the pressure plate from seating on the flywheel. But it is something I'm going to fix if I have to pull the trans again.
For reference, I replaced the clutch because the slave cylinder was hanging up and preventing the clutch from getting fully released. Aka clutch slipping.
in my 2008 ford Ranger Sport with a V6. The smell reminds me of one winter when I had stepped in dog and didn't know it until I was four miles down the road and the heater was on full blast. The smell floods the cabin when the heater is first turned on and warms up, but dissipates after a while. (And I don't have dog on the floor boards or on my boots.)
The smell does not come out the AC vents or when the AC was operated this past summer.
acts like abs sensors could be bad. but the brake pedal goes almost to the floor, after it does it's pulsating. But the abs light does not come on. I already changed brake booster, no change!
View 5 Replies2000 ford ranger, 2.5 2wd
Been having a little problem whenever it rains, the carpet on the passenger side gets soaked through and I'm not really sure where the leak is coming from. the only part of the floor that gets wet is the flat part where the passenger would put their feet, but the parts that slope up towards the dash and towards the middle of the cab stay dry. I've pulled up this part of the carpet, and the rubber grommets are intact and in good shape, and there is no rust or anything on the floorboard. from searching here it seems people have had similar problems, one thing being a leak into the seals around the third brake light above the rear window.
a couple things i should mention is that the air conditioning condenser has been broken for about two years, so could water get blocked up and leak in? since its winter here in PA i haven't used the air con since last summer though. I'm not really sure how long the leak has been happening since I've always kept a floor mat over that spot, and the carpet drys in a few days anyway.
Another thing i should mention is that the weather stripping at the bottom of the window on the drivers side door is not perfectly tight and tends to come out of place when the door is closed hard. this has been happening since i got the truck almost three years ago and a new piece was just put in a month ago (the leak had been occurring before the new piece was installed) when the truck was hit and went in for body work. possibly a drain routing to passenger floor? I should add that I'm sure it's not coolant, it has no odor and feels like water.
Might be a good idea to pull up the whole carpet on passenger's side and sit in the cab during the next storm...
I'm going to work with my cousin change his oil pan on his 2002 passat 1.8T and I would like to know what torque the screws from the oil pan should be? Is the anything specific that I must know about doing this? Anything to make the job easier, faster and to not make mistakes.
View 3 RepliesWhenever it rains a substantial amount, like all day I go out to my 92 Ranger and get in and notice the passenger side rubber floor mat has a puddle of water on it. I look under the floor mat and only the center of the carpet there is wet. I see it's getting the edge of that side of the headliner wet and ruining the new headliner had redone. I didn't realize there was water leaking until I got my headliner redone and put back in. It very well could have been leaking causing the headliner cloth to all tear. It's wet along the top passenger side where the grab handle is and the plastic trim. I thought it was the rain gutter on top of the roof so I put in some black silicone and some of it stopped but not all.
So I thought it was still leaking at the front corner so I put more silicone in. Don't know yet if that was what it was for sure but I'll find out tomorrow because it's raining pretty good right now. But just in case where else could it be getting this much water in. If you go through a carwash, or hose it down for awhile, or even drive while it's raining bad it won't get water inside. I'm not convinced it's the rain channel 100% because on the driver's side the putty filling the rain channel on the roof looks worse than the passenger side and there's no water coming in on the driver's side. There is no water coming in the back or on the back carpet or headliner.
I don't see any evidence around the windshield. I can't understand why only the middle of the passenger side carpet is soaked and not the top or under the seat, unless it's just soaking through the rubber floor mat and not drying out. It's getting so frustrating because I can't visibly find any evidence, I have to wait until it rains and then I can't see why it happens. It's ruining my carpet and my new headliner. I want to replace the carpet but want the leak stopped first. Where are common trouble areas on these 92 Rangers for water leakage?