Ford - Ranger :: 1999 - Can't Get Transmission To Engage The Clutch


Nov 27, 2013

1999 Ford Ranger 2.5L 5 speed transmission. I am a little confused I can not get the transmission to engage the clutch, I replaced the clutch 3 weeks ago, now I have no pressure in the pedal, I have bleed the system 5 attempts with clean solid flow of fluid. What else can I do to fix this or trouble shoot from here?

View 6 Replies

Advertisement

Ford - Ranger :: 1995 - Clutch Does Not Engage / Pedal Starts To Feel A Little Spongy

I have a 1995 Ford Ranger 4 cyl w/ hydraulic clutch, about 95k miles, and an intermittent problem. Normally, my clutch works fine, but a few times a year, normally during the summer, and normally only after driving for a half hour or more, it starts to act up. First, the pedal starts to feel a little spongy. Then, I'll depress the clutch, and when I release it, the peddle comes up, but the clutch does not engage; a few seconds later, the clutch engages fully instantaneously, which usually stalls the engine if I am stopped.

Then, when I try to reengage the clutch so that I can restart the engine, the clutch is very stiff, and I have to pump it a few times, at which time it will depress easily, and then I am usually back to the original problem where the peddle comes up but the clutch does not engage. When I finally make it home and the truck sits for awhile, the clutch then works fine again. I think it is the orig clutch. I have talked to several mechanics about this problem (including the Ford garage!), and they are mystified. One mechanic thinks that it is a problem with the master and slave cylinder combo, and can replace them.

View 5 Replies

Ford Transmission :: No Clutch / Truck Will Not Engage A Gear While Running

I have a 2001 m5r2 ford f-150 standard transmission. i have replaced the slave cyl., the entire clutch assy., the master cyl. pilot bearing. the trans. will engage all five gears plus reverse while truck is off but will not engage a gear while running. i have bled and bled and bled and still will not engage.

View 1 Replies

Ford Ranger / B-Series :: Clutch Start To Engage / Disengage At Half Way Point On The Pedal Travel?

So I just had my entire clutch replaced while another repair was taking place. What I've noticed is the "clutch engagement" has changed. Where as I would have the clutch start to engage/disengage at the 1/2 way point on the pedal travel is now the last 1/4 of the pedal. Is this a "normal reaction to a new clutch that just takes getting used to or is there an adjustment I can fine turn it with? Do I just have to wait for it to "break in"? When I replaced the clutch on my dearly departed 94 ranger, I replaced the bearings & disc only reusing the pressure plate and did not have this issue.

View 3 Replies

Ford - Ranger :: 2002 - Transmission Damaged By Changing Clutch?

if a 2002 4x2 ford ranger was towed into a shop because the clutch failed is there anyway the #2 syncro or anyother internal part of the transmission could be damaged while the service department repalced the clutch?

View 1 Replies

Ford Ranger / B-Series :: 1997 - Transmission And Clutch Interchange

Will a clutch/flywheel and 5 spd from a 1997 ranger bolt up to an older 1980ish engine that had a 4 spd? What about the starter?

View 1 Replies

Ford Ranger / B-Series :: 1999 - 4x4 Does Not Engage

I drive a 1999 ford ranger and can't figure out why my 4x4 won't engage. I have vacuum all the way down to the hubs and when I turn the switch it sounds like the transfer switch is engaging but the 4x4 still doesn't engage. What do you all think could be the issue? I thought about just putting a set of the manual locking hubs on it and just be done with it.

View 1 Replies

Ford Ranger / B-Series :: 2003 - Hard Shift - Transmission Or Clutch?

The truck: 03 Ranger, 2wd, 2.3L, 5spd, 160k mi

I bought the truck two years ago and it's always been difficult to shift (especially into 1st, 2nd, 3rd). I don't drive it often and only put 5k mi on it since I bought it.

The problem: Someone more mechanically inclined than I once told me that the hard shifting is probably due to the clutch not fully releasing due to low hydraulic pressure brought about by a failing slave cylinder.

I just noticed today that there is a high-pitched squeaking coming from somewhere on the truck. At first, I thought it was the rear end, but now, after pulling it into the driveway, I noticed that the squeaking noise vanishes when I push in the clutch pedal and returns after I release the clutch pedal and drive in 1st gear.

The transmission oil level is good, but I've never changed it and I'm not sure if the previous owner ever did either. I'm hoping I haven't damaged the transmission.

After reading a few threads, it seems the problem might be the input shaft bearing. To replace it, I'd need to drop the transmission and borrow a couple of tools I don't have (feeler gauge and bearing puller). If the ISB is the problem, it seems like it would be a good idea to change it now before it seizes and leaves me stranded somewhere.

View 12 Replies

Passat (B5) :: 1999 - Clutch Does Not Engage

I traded for a 99 passat 1.8t aeb based on the assumption the slave cylinder was out. My 3rd b5 5 speed. Kid told me clutch pedal had no pressure and fell to floor.easy fix! Get the car to my house from 2 hours away and this is not the case.Pedal is fine. Decent clutch pedal starts with clutch pushed in. But clutch does not engage. Even when motor off or on goes into all gears without clutch pushed in. no engagement. So I put in new slave and bleed out.

Car no longer stuck in neutral shifts fine. Put in reverse barely crawls but is MOVING! Put into first and start to pull forward..stops moving. No clunks or booms just back to ALL neutral. starts with clutch but wont engage. So try bleeding again nothing.. I think it is the clutch but i dont want to spend 1400 if i dont have to though the car is worth it. Going to replace dual mass as well. The cv joints are fine. so thinking throw out or pressure plate. i work on this car like crazy but im definitely not going to do the clutch. Not enough time or a warm dry location. I haven't checked clutch master yet but with slave bleeding out,no leaks and a firm pedal i dont believe she is the culprit..

View 6 Replies

Ford Ranger / B-Series :: 1999 - Four Wheel Drive Will Not Engage

I bought a 99 ranger few months ago cant the 4x4 has not worked in the truck for about 4 years. Bought it off my dad. He hasn't figured it out the t case locks in the drive shaft spins but hubs will not lock in. Has new hubs in it and still not working. Trying to get it fixed so I can park the diesel for the winter and run the ranger.

View 3 Replies

Ford Ranger / B-Series :: 1986 - Transmission Overhaul - Hard To Get Clutch Into Gear From Neutral

Rebuild on the Mazda 5 speed transmission. My 1986 Ranger 2.3 Four cylinder has 280,000 miles and the clutch has never been replaced. It's not slipping but I'm having trouble getting it into gear from neutral. Was told that the release springs on the clutch plate have weakened causing the clutch to not release completely so figured it's time to replace it. It's done well the last 280,000 miles. The question I have : overhauling on one of these Mazda trans and how difficult was it. Any special tools required, etc...I see Autozone has a rebuild kit which appears to have bearings, seals and gaskets. Figured while it was out I would go ahead and rebuild it myself if I can. Rebuilt a few engines but never touched a trans.

View 4 Replies

Honda - Cr-v :: 1999 - Total Clutch Failure / Does Not Engage Fully When Let Out

Our 1999 CRV has had the clutch fail several times in the past year. The pattern is that you notice it slipping a bit now and then, but trending worse over a few days. Then it gets dramatically worse in a period of minutes: it does not engage fully when let out. The pedal feels fine, the engine is running fine, but power is not transmitted to the wheels.

On two occasions, we were able to take it directly and the mechanic resolved the problem with some adjustment to the master cylinder, or something like that (my wife spoke to the mechanic and it was many months ago).

Last winter, I was driving as the problem was recurring and I found myself nursing the slipping clutch up a steep one mile grade. At the top of the hill, totally flat ground, the problem continued to get worse for the next half mile, till there was no power at all! Engine fine, pedal action fine, but effectively the clutch was permanently disengaged. I left the car there over night. The next morning, before calling for a tow, I tried again and the clutch was working! I could tell it was still slipping a bit, but it was no problem to drive to the mechanic, who fixed the problem again for just a hundred bucks or so.

Yesterday, my wife again found that the clutch failed completely over the course of a few miles driving. She had to be towed. Today the mechanic says they can't reproduce the problem!

View 5 Replies

Ford Ranger / B-Series :: 1999 XLT V6 - No Clutch / Can't Shift

When I got home today I went to back into my parking spot and couldn't get my truck in reverse, or any other gear for that matter.

I've been suspecting something was going to go wrong because the last few weeks or so when I push the clutch in it sounded like bb's rolling around in a metal coffee can. Since I have owned it (2 yrs) the clutch has seemed funny anyhow, as in I really have to feather it so it doesn't grab and stall out.

So I've visually inspected what I can so far. Master cylinder fluid is at a proper level and I pulled the inspection cover on the transmission. I didn't see any fluid and reached inside and there wasn't residue in there either. I observed the throwout bearing pushing the clutch cover fingers in when the pedal is pressed and that is about it.

Just wondering about some additional checks I can perform to pinpoint the problem, as well as how to fix it and get rolling again.

1999 Ford Ranger 4x4 XLT
3.0 V6
134,xxx miles
No modifications

View 6 Replies

Ford Super Duty (1999-2016) :: Transmission Will Not Engage In Drive Or Reverse After Replacement

I have a 1999 F250 super duty that blew a front seal on the transmission two weeks ago. I sent it to a shop and they replaced the seal, and torque converter. However when they put it back in it will not engage in drive or reverse. After working on it several days we replaced the transmission with another one from a service company. This replacement came with a 90 day warranty. However once it was installed it does the same thing and will not engage in drive, or reverse. I am not sure what is going on but with two doing the same thing it makes me thing maybe electrical or something else.

View 1 Replies

Ford Ranger / B-Series :: 1999 - Clutch Slipping - Replacement?

My clutch is weak and slips sometimes and I need to replace it. ,I have replaced the clutch disc in other trucks but never a Ranger.

1999 3.0, 5 speed stick, Extended cab....

View 11 Replies

Ford Super Duty (1999-2016) :: 2015 - Delay In Transmission To Engage When Start And Put Shifter In D

2015 F-250 4X4 CC gas truck. 6R140 Transmission..

My truck has 6500 miles on it and since day one when I put my shifter in (D) there is a 3-4 sec delay in the transmission to engage every morning when I start out, rest of the time there is no delay even when the truck sits all day at work (about 9 hours). I have read in 2011 (?) that the transmission was loosening it's prime and would cause this problem, so how it's got me thinking.

View 9 Replies

Ford Ranger / B-Series :: 1999 - Grinding Noise When Let The Clutch Up Off Floor

1999 ranger 3.0, 5 speed stick. I was backing out of my driveway but there was a car coming so i pushed in the clutch and waited for the car to pass, when I let clutch pedal up off floor i heard a grinding noise, a little while latter did the same thing in first. Is this a first and reverse gear scyronizer or something else. What causes this and how to fix it ?

View 10 Replies

Ford Ranger / B-Series :: 1999 - Clutch Safety Starting Switch Going Out

I have a 1999 ford ranger and I believe my Clutch safety starting switch is going out. Some times I push my clutch in and truck starts fine other times it will not turn over so I stomp clutch and then it starts. My question is, is there any way to bypass this switch?

View 5 Replies

Ford Super Duty (1999-2016) :: Transmission Shifted Into Drive Takes 5 Seconds Or More For It To Engage Hard

I have a 2006 F250 Lariat super Duty / 6.0 L engine / 143000+ miles / once started and transmission shifted into drive it takes 5 seconds or more for it to engage hard or if I build up the RMS then it jumps into gear hard, after it gets going it feels like I am driving on a washboard until it get warmed up good 10 mile or so. Is it the transmission filter and if so which one, I understand there is a small one on the outside of the transmission if so where? I can't find it.

View 14 Replies

Ford A/C :: Clutch Won't Engage

I have a 1999 Winnebago Motorhome on a F53 Ford V10 Chassis and the A/C clutch will not engage when turning on the A/C. I have check the Freon 134A and it appears to be fine (in the red zone) and actually put a jumper across the pressure switch connector (harness side) and it still will not engage. Is there a fuse within the circuit if so, where it may be located?

View 1 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 - Transmission Work Slowly - Hesitates To Engage Drive After Reverse?

I have a 2002 7.3 e350 quigley 4x4 Sportsmobile with 312k miles. 2nd owner. Bought it with 295k miles 2 years ago. From what I gathered the tranny is original.

After reversing at a downhill angle, stopping, and shifting the lever to Drive, the tranny doesn't seem to put Drive in gear and depending on the angle of the slope, the van will roll back or barely creeps forward even with throttle. Put it in 1st gear, and the tranny engages that in gear and drives forward no issues, then I can shift to 2nd, then Drive and the tranny shifts fine after that.

No weird tranny noises or clunking. Noticed this issue about a month ago or about a couple thousand miles ago. Did tranny service (drain, filter, fill) at the ford dealership at 305k months ago.

I can only replicate this issue when Reversing on a down slope. On a flat surface van Reverses and engages Drive like normal.

View 7 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved