Ford - Ranger :: 1998 - Check Engine Light Came On / Misfire Monitor Malfunction
Apr 1, 2012
I have a '98 For Ranger. After 256,000 miles, I recently had a new (rebuilt) motor put in my truck. After about 2 days of driving with the new engine, the Check Engine light came on. I went to Auto Zone and had the codes checked, and these two codes came up:
"Misfire monitor malfunction"
"Oxygen circuit slow response bank 2 sensor 1"
The guy at Auto Zone couldn't tell me what they meant. Is this something serious that needs to be checked out immediately or have anything to do with the new motor that was put in?
View 3 Replies
Advertisement
OK, got a check engine light today when I fired up the Ranger. Like I posted previously it is running kind of rough so guess I know why now.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use? Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
View 6 Replies
I just bought a 1998 ford ranger with 228000 miles on it seems to run fine has the 2.5 4 cylinder with auto trans. Check engine light is on and code is a PO171. I've cleaned the mass air flow sensor and fixing to install new fuel filter. what the problem could be?
View 12 Replies
1997 Ford Ranger with 190K miles has check engine light on with P302 computer code, meaning misfire on cylinder 2. Engine runs rough at idle only once it warms up, which only takes a minute. It is usually fine while driving, but it's a lot easier to feel a misfire at lower RPMs than at higher ones. Added fuel injector cleaner to gas for a couple tanks, no change. My mechanic has checked spark plugs, fuel injector, o2 sensor, and everything is ok. Dry compression test shows good compression. He thinks it may be a valve sticking, which means a valve job: expensive. Is there anything else that can be done? Why is there no misfire when it is first started?
View 9 Replies
I have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 Replies
Got a 1996 Ford Ranger with the 4.0L in it that has a misfire on the #3 cylinder and giving check engine code: P303. Have tried new plugs, wires, distributor, switching out the coil pack with a known good, checked injectors for pulse, checked injectors, moved injectors and still the misfire remains on #3. Removed the valve covers and all appears to be well.
View 14 Replies
At a stoplight earlier today, my ICE was running though I thought it should have shut down. I checked the engine monitor display on the dash, and it didn't indicate that the ICE was on, even though it very obviously was. The same thing happened a bit later. My worries are: 1) there was clearly an error in what the dash display was showing, since the engine was on and it indicated that it wasn't, and 2) maybe the engine really should have shut down, but for some reason it didn't .
View 5 Replies
I’ve got a 1998 Ranger with 166,000 miles and it’s starting this weird idle at stops where the engine drops about 150 RPM’s and then fluctuates. The problem is intermittent and no pattern as to cold or warm engine. I changed the plugs and wires at 100,000 and the plugs again at 150,000, so the wires have 66,000 and the plugs 16,000. I really don't want to shotgun the plugs, wires and coil pack. I understand that vacuum might have something to do with my problem?
View 14 Replies
I had recently thrown a code for a 'misfire detection monitor disabled' , never did address the issue. But just the other day the service engine light went off, the light had been on all this time and now it's off. My question is, how do I know if the light is just burned out. Is there something safe I could do to make the light come back on just to see if the light is actually still works.
2000 f 150 4.2 v6 232,000 miles ....
View 6 Replies
So when I bought the car, it had a check engine light. I had it checked it said cylinder 5 misfire. I assumed it was the glow plug so I bought it and replaced the glow plugs myself. Check engine light went away for about a day then came back on. Got it checked again and still said cylinder 5 misfire. This is my first diesel and I'm clueless as to what's wrong.
2001 7.3 Limited with 232k miles Bergen County NJ.
View 2 Replies
I have an old 2000 Ford Taurus that has been having some misfire issues. I replaced the wires and plugs about a year ago and hooray! it worked... until about a month ago when the check engine light came one. Misfire in cylinders 1 and 3... again. I ran some SeaFoam through and it did okay until this week, when the warning/flashing check engine light came back.
It is idling very hard (expected) and feels like it is trying to stall, even before the misfire came back (also to be expected??). So here is the question: is this a coil pack issue, or something more sinister (and expensive)?
View 9 Replies
This morning, I tried to start the 2003 Prius and got a 'check engine' light and nothing. The cabin lights were bright so the 12V looked OK. After three tries, I used the VOM and measured 12.55 V on the battery. But the traction battery level looked unusually low.
So I tried again and it started. Using the ScanGauge, no codes were displayed. So I turned the car off and on three times and cleared the "check engine" light. Then I connected the Auto Ingenuity and read out:
P1636 - HV ECU Malfunction on the HV ECU to ECM bus.
C1213 - HV ECU Communication Circuit Malfunction between HV ECU and Brake ECU
P3002 - HV ECU Communication Malfunction on the HV ECU to Battery ECU
So it looks like there was an HV ECU problem that 'cleared while testing.' Certainly it makes sense to inspect the HV ECU connectors and re-seat them and clean out any debris.
View 2 Replies
So I have been having some troubles with my 2003 F150 4.6L ... Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:
"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "
So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors??? I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?
View 6 Replies
I have a 99 Ford Explorer - w/217k miles. (2nd owner) .. I got an oil change 3 weeks ago, tune up 2 mos ago, and new brakes/tires within the last 6 mos, oh, and Brother-In-Law just recharged my a/c last week.
Runs well, and I hope to keep it for another few years, but having problem lately.
Check Engine light keeps coming on - I've taken it in, and they read the code, and it comes up with a misfire. Mechanic resets it, and it will stay off for a few days/weeks, and then comes back on.
View 3 Replies
I have a 2005 f150 with 96,000 miles. Long story short, last August I was headed to the mountains going up a steep long hill and the engine light come on. once i was over the pass the light went off. During my 4 wheelin' trip it never came back on until I was headed home and going over another pass and then it stayed on for a couple of days. I had it checked and it was a cylinder 5 misfire. I did some research and found that replacing the coil cover might fix the problem and if not the spark plugs would need to be changed.
I changed the coil cover, problems solved... until I headed to the mountains. light came on and then eventually went off later that day. I didnt think much of it. then a few months later i was headed to the mountains again and the light came on in the same place on the steep incline hill. I. took it back to the shop, same reading. I decided it was time to replace the spark plugs anyways so I would invest. I have new plugs and everything is good however, I had no plans to go to the mountains in the near future. Now, a few months later I headed to the mountains and crossed my fingers it would not come on but it did.
I've done the research again and it seemed like the coil cover and spark plugs are usually the cause of the problem...however I have changed mine. The light is now off again. I don't understand what is triggering the problem and what is really happening and if it is safe to keep taking to the mountains with this happening. I did notice that everything was fine at 60MPH but once i hit the hill and steeped on the gas to go 65 and hit 4-5RMP that is when the check engine light came on...
View 12 Replies
I have a 2001 Ford Windstar Sports SE with 155K miles. I did a tune-up eight months ago. With the tune up I had to replace the fuel pump because it was defective. Later, I found that there were misfires occurring since I was getting slow acceleration. I had the spark plugs on the guilty cylinders replaced again and the spark plug wires.
Periodically, I have had to return to the shop to have the vehicle checked. I sometimes get a blinking check engine light while trying to accelerate, which now occurs only while it is raining or I am exiting the car wash. The shop is at a loss as to what it is (spark plugs and wires are fine, no lose connections noticed). I am wondering if I should take it to someone else. Of course, taking it somewhere else will cost me $100 to check on someone's else work.
The shop replaced the ignition coil. Distributor cap is fine. They keep saying that the engine is running fine while in the shop and do not get any codes. I had them drive it while it was raining and they discovered that cylinder 4 is misfiring. They worked on the cylinder. The vehicle runs well, until it rains or I wash it.
My questions to the group, "If everything is OK, how come it is misfiring? What are they missing? What is the connection to the moisture?"
View 14 Replies
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 Replies
So when I bought the car, it had a check engine light. I had it checked it said cylinder 5 misfire. I assumed it was the glow plug so I bought it and replaced the glow plugs myself. Check engine light went away for about a day then came back on. Got it checked again and still said cylinder 5 misfire. This is my first diesel and I'm clueless as to what's wrong. Any way to check what's wrong myself?
Also just to double check, the cylinder number is 1, 3, 5, 7 for the passenger side front to back right? And 2, 4, 6, 8 for drivers side? And front to back means when looking at the front of the car? 2001 7.3 Excursion Limited with 232k miles...
View 6 Replies
I have a 2008 FX2 5.4L F150. Recently it began to lose power on a friend driving it out of town. He got a check engine light then it just progressively became unable to produce power. It ran but he got down to 10 mph before he could get to a firestone. I got it to a local Ford dealer and they say i need a new engine. They gave me codes for cam sensor and timing and #5 and #6 misfire. (344, 345)
No oil in radiator, no water in oil. The crazy thing is it runs like the day i bought it in Park. But once in gear it begins to cough and then eventually shudders and dies. I haven't changed plugs ever. I know... At about 75 miles it began to idle rough at times and in reverse. But once I revved up it went away.
I replaced both cam sensors but no luck. Today i put it on a tow truck to get a second opinion from a local engine shop. I actually backed it down my driveway, and pulled up to the tow truck with no issues. weird...
View 2 Replies
Yesterday, I was driving home in EV mode, PHEV on, about 80°F, no hills, not accelerating, SOC about 4 bars, about 1/2 mile out, when it dropped out of EV mode, and then I got the red triangle and the check engine light. Today I grabbed the code with an OBD2 reader, and got this:
Freeze Frame Information:
1. DTC for which Freeze Frame was Stored - P0A92.
2. Engine Coolant Temp - 138.20 °F.
3. Engine RPM - 1,888.00 Rpm.
4. Vehicle Speed Sensor - 14.91 Mph.
5. Intake Air Temperature - 96.80 °F.
6. Time Since Engine Start - 101 Sec.
7. # Warm-ups since DTC Cleared - 74.
8. Distance since DTC Cleared - 706.50 Mi.
9. Control Module Voltage - 13.69 V.
10. Ambient Air Temperature - 80.60 °F.
11. Accelerator Pedal Position D - 30.98 %.
12. Accelerator Pedal Position E - 46.67 %.
13. Time since DTC Cleared - 30 Hr32sec.
Does this happen because it's in EV mode? Do I just have to put up with it every so often? (This is the second time it happened.)
View 4 Replies
So this little gem of an SUV has been good enough to me over the year that I have had it, but it is one of those used vehicles that has me scared to look underneath cause there is always something a miss.
I have been having some power problems and the OBD check engine light has been coming on. The engine like to putter like if it's not getting enough fuel from a clogged fuel filter when it gets going, hot or cold. Have confirmed that the fuel pump is with proper voltage and pressure. Though haven't noticed a big difference with the new filter. The check engine light cycles a code of 21, which is refinanced to the O2 sensor, both upstream and down stream. That tells me that there are TWO O2 sensors for this model. And research has confirmed this. One ahead of the cat and one behind the cat.
Here's the kicker, I only have one O2 sensor at the head of the cat and the location of where the second one would be located is only a solid section of pipe from cat to muffler. I haven't been able to track down the plug connection for the second sensor and these codes and problem only came after I gave the Jeep a tune up.
1994 Jeep Grand Cherokee Limited V8
View 5 Replies
