I have a 93 Ford Ranger I can not get to start. The battery is new, I have replaced the starter and the fuel pump but the truck still turns without starting. I thought maybe the Starter Rely might be the problem but I get spark from it when I do the screwdriver test. I am running out of money replacing all these parts without any success.
View 11 RepliesI recently picked up a 93 ranger sport 4x4 with 2.3L engine and 5spd.. Has run fine for the first 2 weeks of ownership but yesterday morning, it started cutting out on the highway. When I say cutting it is like all loss of power for a brief instant and then it right back without even losing any speed, I could watch tach drop from 2500 to 2k and then right back to 2500 again..
Did it sporadically all the way home about 10 miles sometimes once in a mile other times 6-7 times in a mile. Truck has 126k on it, and within last 26k miles PO replaced timing belt, coil packs, plugs, wires, ICM, and just before i picked it up from him a new EGR and fuel filter.
No check engine light
Fast forward to this AM
Wouldn't start at all, i can hear fuel pump spinning and she cranks and cranks but no start up.... played with multiple things including the ICM but found 2 of 3 heads rounded off so i cant remove it until i can get it in to my garage and dremel those suckers off..
Went and bought a replacement ICM figured i could plug it in run a ground from the bottom left hand bolt hole so i could get it fired up and in to my garage.. plugged the new one in grounded it and it still wouldn't start...
So I decided to replug the original ICM back in and grab my spark plug tester, remove number 3 plug wire on passengers side insert the tester and have my wife crank it over and wonder of wonder it fires up...
shut it down remove the tester and have her start it up again and it fires right back up so i let it warm up for 15 minutes.. grab my autoxray.. shut it down hook up the scan tool and run the KOEO scan.. gives me a passed 111 code... OK lets start it back up and run the KOER test.. wont start back up.. reinstall the spark plug tester to #3 wire and NOW it has no spark..
I have a 93 taurus 3.8L V6 automatic GL. After I start my car up with my foot on the brake it won't shift into gear from park. But if I pump the brakes a few times it will then go into gear. What is wrong with my car?
View 7 RepliesI have a 93 explorer it ran fine then when I drove it today it stalled put it in park it started but wont go into gear when shifted?
View 1 RepliesMy 1993 Ford Ranger XLT w 170,000 miles has been having an issue with not starting. It cranks fine. At first (for the last year), the fuel pump didn't sound right or didn't come on at all; when normal, you hear it for three seconds or so after turning key on. I have replaced fuel pump/relay/filter. Now, in the last week, it also will not idle after initial start, and I have to rapidly pump the accelerator lest it dies again. This whole process can take ten minutes or more to get the stars in proper alignment. This morning, I had to give up and drive my other beater into town. In addition to the parts I mentioned, I also replaced the ignition switch thinking not correct voltage to pump. I finally traced wires and do indeed have 12 volts to the pump (under the bed, after the inertia switch and all harness plugs). It has a new windshield, new tires, cold old R-12 A/C, and it's paid for.
View 8 RepliesThe motor turns over but it just don't seem to have enough power to start. Have not tried to arc check from the plug wires. I believe the coil is internal on this model.
View 1 RepliesMy '93 Ford Ranger died on the road three days ago. The motor simply stopped. Battery is good. the engine will crank but it will not engage. Had it towed to my Shade-tree mechanic he is puzzled. Says that trouble code 5931111111 indicates an air conditioning problem but that doesn't make any sense. The truck is 4 cylinder 2WD.
View 1 RepliesI have a 93 Ford ranger that will not start. It was cranking fine. It would take 2 or 3 tries when it was cold but once warmed up it ran fine and would crank right back up until it was cold again. The last 3 or 4 times I drove the truck it fired right up on the 1st try. Then the last time I drove it, it cranked right up and I drove it between 5 and 10 miles. It sat for about an hour and when I tried to crank it, it wouldn't start. At first it sounded like it wanted to but after a few seconds all it would do is turn over.
After about a week of sitting I was able to crank it up again. It fired right up. I let it run for 15 minutes or so turning it off and re-cranking it. About 4 or 5 times. Then the last time I cut it off and tried to crank it back up it wouldn't start again. I replaced the pickup coil in the distributor, cleaned off the rotor button and leads on the distributor cap (they didn't look bad and were working fine before), I checked to see if I was getting spark but Im not getting it from the spark plug wires or directly from the coil wire.
I checked with a test light to see if I was getting power to the coil and distributor from the wiring harnesses. With the key on power is going into both but I'm not getting any arch when I test directly from the coil wire or the spark plug wires. Ive also switched out the relays and tested the coil and starter solenoid on another vehicle and they work fine. My next step I'm thinking about replacing the computer but don't want to spend on a part a can't return if thats not the problem.
I am starting to work on my 93 ranger when funds are there. But my question is do i need a Cat. for PA state emissions? I have heard you do but then I hear you don't. I have also heard a few things on the fuel millage and power.... Looking for some info on this because I am not trying to cut it off and have to go back and fix it again... I want to do it once and be done with that part!
View 3 RepliesToday on my way to work my 1993 ford ranger would shift fine but would refuse to go over 35mph and shook pretty bad. I don't know where to start...
View 6 RepliesNot only will it not go into gear, truck will not start unless clutch is to the floor, and in neutral (it's only possible place) if you pick the pedal up 1/4 inch off the floor the odometer starts spinning around 1 mile in 5 seconds.... if you lift it any more it kills the engine like you shut it off with the key.... odometer reads 99,004 miles now (the last 2 are mine) I bought this truck like this ....
View 3 Replies1993 ford ranger 4 CLY 2 WD getting spark gas to injectors will only start when fluid is sprayed in air intake. have replaced fuel pu,p. fuel filter air intake regulator. ran okay till ran out of gas.
View 2 RepliesMy '93 Ford Ranger suddenly died while I was driving, no sputtering or bucking, it was just as though I had turned the key off. When i tried to restart, the engine would turn over but not engage. It's as though the engine is either getting no gas and/or spark. My shade-tree mechanic says he got a diagnostic code that was #539 followed by #1 seven times at two second intervals. he says he ran the test 6 times and got the same result every time. What this means?
View 10 RepliesI have a ranger as said in title. No a/c. I noticed my belt was cracked very badly so I bought a new one. Dayco made for Ford and Mazda 3.0L V6. Looked the same length as the old one so I put it on and all was good. Then about 2 days later it started squeaking very loudly, not all the time, just 1500 rpm and higher. The hotter the motor got (not overheating just to running temp) the higher rpm it took for it to squeak. I put a stethoscope on all the pulleys/pumps and alt. It sounded the strongest on the idler.
So I replaced the idler and bearing (which the bearing was bad, but not the source of sound) it wasn't that. So I thought I'd give the belt a couple days, maybe it was too tight causing a bearing to get too tight and squeak. And the more I drove it the louder it got with less rpm needed to make it squeak. So I tried belt dressing, and still no fix. So today I put the old belt back on to see if that was the issue. Sure enough, it started up and squeaked just the same, but I tried the belt dressing on the old belt and it went silent, even at 3000 rpm. So I assume from this the new belt was a smidge too big. Right?
How do you remove this clip holding the wiper linkage to the back of the motor? I can't see what kind of clip it is to know how to remove it. Ford says to remove the wiper pivot and let it drop. Is that necessary? I can't barely get to the back of the motor so I'm having to feel the clip and remove it but since I don't even know what kind of clip it is it makes it so much harder. Does the cowl cover not come off or is it just this access panel?
View 3 RepliesI'm new to the whole Ranger truck thing since buying a 1993 Ranger 4x4 for my 14 y/o son. It has a 4 inch suspension lift and a 3 inch body lift running 33x10.5x15 tires. The front sway bar is not hooked up. I know that i will need drop brackets for the sway bar but my question is about the end links needed for this truck. There are 2 tabs with provisions for a horizontal bolt on each side of the twin I-beam where the end link would attach and the sway bar has a single horizontal hole on each end. Searching for replacement links at various auto parts websites only seems to yield the standard end links that consist of a straight bolt with a nut on each end and the rubber insulators. That clearly is not the correct end link for my application. Not sure if the front suspension is the factory installed unit or if it was swapped some time in the part.
View 4 RepliesI am trying to replace the key lock cylinder (where you insert your key to start the truck) in my 93 Ranger. Using the Haynes manual, I have removed the steering wheel cover (I don't have airbags), pulled the steering wheel, removed the 3 plastic decorative shrouds and looked at a naked steering column assembly. The manual says there is a 1/8" hole on the bottom of the steering assembly where you can push up the actuator pin to release the lock cylinder assembly.
I looked and looked (even with a flashlight) and could not find a hole. I looked at the new key lock cylinder assembly and found the little actuator pin so I sorta know where the pin would be in the installed assembly. The entire key lock assembly is enshrouded (is that a word?) in the cast aluminum steering assembly.
There was a small metal plate - but that plate is just for access of the release of the steering wheel lock actuator (so I carefully bent it back!!). I know all this is for theft protection, but the truck is co safe I can't even replace the lock assembly.
Where the modulater valve is on my A4LD tranny. I have a 93' ranger XLT extra cab 2wd with 4.0 engine. I have looked all over the tranny and thought it would be somewhere I could see it. I know I had one on my old full size Ford truck with C6.
View 7 RepliesWhere is the location of the fill plug for a 93 Ranger transfer case? The damper is off and I see the drain plug. Is the fill plug behind the electric motor that shifts the case? I can see what may be a plug there that looks plastic with a very small hex head in the center of it. Is that it?
Also, my Haynes manual says to use Mercon ATF in the transfer case. I see where Valvoline has a Mercon equivalent. What do ATF brand people here recommend?
I have a 1979 Ford Thunderbird with a V8 5.0 liter engine. Here's the mysterious problem... the engine turns over when I turn the key but stalls when the key is released. Thinking that the alternator died, I replaced it with a new re-manufactured unit and the car's symptoms stayed the same. Also checked the fuses and the fuel filter and found that plenty of fuel is getting to the carburetor. This issue with the car not starting appeared literally overnight after I attempted to install a new radio. Prior to this the car ran reasonably well – always started easily and ran without a problem. Wondering if there is a possibility that I fried some part of the electrical system when I fussed around with all the wiring under the dash. Someone else had attempted the radio installation previously so the wiring there was already a mess of cuts and re-connections and was hard to sort out.
View 7 RepliesSo went today and bought a 1993 ranger 4x4 ext cab 4.0! Runs good some bad handy work that i need to fix but truck has plenty of power and good handling...
issue 1- 4x4 not engaging. the light by the push buttons does not come on and you dont hear the "clicking" of the relay trying to engage. so whats the problem and how do i fix it?
issue 2- when clutch is fully depressed and you go to shift (this is only sometimes) you can feel and hear it grind just for a quick sec. and forget about down shifting you cant do that without slowing down. so maybe new clutch?
issue 3- at 65 the vehicle does shake a little otherwise but pretty smooth. any tips on how to smooth it out? maybe new ball joints? tighten some stuff up maybe?