Ford - Ranger :: 1990 Will Turn Over But Isn't Firing


Mar 28, 2011

199) Ford Ranger will turn over but isn't firing. We've replaced the battery, positive battery cable, distributor, distributor wires, the selonoid inside the distributor, starter selonoid.

View 18 Replies

Advertisement

Ford Ranger / B-Series :: 1990 V6 3 Cylinders On Driver Side Not Firing

Is there something that would make the 3 cylinders on the drivers side of a 1990 2.9l not fire? I have spark to the plugs and pressure/fuel at the schrader valve on the fuel rail. The passenger side cylinders are firing fine and the engine runs (roughly) on these 3 cylinders. Truck was running just fine, then all of a sudden, drivers side is dead. Is there a fuse or something that controls these three fuel injectors?

View 1 Replies

Ford Ranger / B-Series :: 1986 - Engine Won't Firing

i have a 1986 ford ranger with a bored out 2.9 v6 that is not getting spark sent to the spark plugs disrtibutor has been changed along with spark plug wires any clue what the problem is

View 1 Replies

Ford Ranger / B-Series :: Coil Is Sending Spark But Cylinders 4 / 5 And 6 Not Firing

Al right i have a 94 ranger 4.0 4x4 auto 186k ... The truck has new bosch double plat plugs gaped .054, new wires, MAF, TPS, FPR, O2 sensors, ECTS and I checked the intake air charge sensor and is fine ....

My issue is cylinders 4,5 and 6 dont fire... the coil is sending a spark, i can pull the plugs one at a time and watch them fire (strong blue spark)... All fuel injectors do not leak and spray a perfect cone out of all 4 holes and noid light test is good ...

The truck runs like crap back firing and no power under 4k and i can pull off all 3 wires for bank one and it make no difference and when i unplug the injectors no more back fire....

View 14 Replies

Ford Ranger / B-Series :: 1994 - Sputtering / Back Firing / No Power

Background - I just got done changing a few things... Exhaust Manifold/gasket, battery cables, valve cover gasket, oil cooler gasket and hoses, power steering pump and hoses, and ball joints. Most of this has nothing to do with the issue that came up as I am driving it back to return it to her.

While out on the freeway, I initially notice subtle power losses and surges. These quickly escalate into almost total power loss with back firing, sputtering and much more noticeable surges in power. The check engine light was turning off then on a few times before pretty much deciding to stay on.

So I nurse it back home on back roads due to its inability to maintain freeway speeds. I proceed to check everything I touched paying special attention to the exhaust manifold and surrounding area. The new manifold came from the j/y and was barely used so I had initially just stuck with the O2 sensor that came with it; I changed this to the one the vehicle had previously been employing as it was not exhibiting these symptoms until after the job was done. I also double checked all the hoses, intake tube, wires and connectors; everything is connected.

From here, I research the method of pulling codes on OBD-1 vehicles by making the check engine light flash. It flashed a 111 and a 172 at the same time; the information I could find said the 111 means everything is normal, and the 172 suggested O2 or MAF. I am reasonably sure the O2 is not the problem so I focused on the MAF. Disconnecting it while running seemed to improve the way it idled so via the process of deduction, which also included the consideration of typical symptoms of MAF sensor failure, I proceeded to replacing the MAF sensor which amounted to little improvement.

At this moment in time the check engine light has not returned but it is clearly not in a drive-able state of being. It actually seems to have ever so slightly improved though.

Additionally, the symptoms only exist when the engine is hot and has been driven; it drives normally for 5-10 minutes until it gets to operating temperature then it starts to crap out. After changing the MAF sensor, I let it idle for 20 minutes and it was fine until about 2 minutes into the test drive.

Speculation - I am thinking spark plugs could also be a culprit as its has been forever since a tune-up but the sudden onset of this condition make me doubt this a little; it also has 8 plugs so even if one or two crapped out it should still run better than this I would think.

View 14 Replies

Ford Ranger / B-Series :: 1988 V6 Starts And Runs But Shuddering - Cylinder Not Firing?

'88 Ranger 2.9L V6 starts and runs but shuddering. Most noticeable when shifting and revving the engine. Will a dead cylinder cause this? How do I check?

View 2 Replies

Ford Ranger / B-Series :: 1987 Truck Won't Start / Ignition Firing While Key On Engine Off

I've got an 87 ford ranger 4x4. The truck won't start. The ignition is firing off with the key on engine off. When I got the truck the transfer case was blown. The people I got the truck from drove it to here it sat. I check the wiring but the transfer case to make sure it diet get damaged causing a sort. When I got the pcm was missing. Took one out of a bronco 2 and changed the relays on the fender. Here what I've done so far

Relays
Pcm
Complete tune up.
Distributor and ignition module
Replaced and repair some grounds.

View 1 Replies

Ford F-150 (2004-2008) :: P1299 Code - Won't Start - Turn Over But Not Firing?

Just went out to start the truck (2006 4.2L) and no start...turns over but isn't firing.

I checked codes and got a P1299. She was stone cold and ran perfectly last night - never overheated.

I suspect ground or other wiring...where should I start?

View 4 Replies

Ford - Ranger :: 1990 - 5th Gear Kicks Out

90 Ranger with 5 speed manual, Every thing works as it should untill you put it into 5th, lift the clutch pedel and you fine, the tac responds and I asume your now in gear, but press on the gas pedel to give it a load. whhhhhiiiinnnkkk and the gear selector kicks back to netrual.Also I did remove an inspection panel from bottom center of the tranz and could see no sighns or damage, rounded or broken teeth.It's been sugested that it's just time to re do the clutch, if so why do all the other gear selections work without any problems?

2.9 v6 w/95k and I don't know the history.

View 5 Replies

Ford - Ranger :: 1990 - Grinding Sound

My 90 Ford Ranger 4 banger is my construction beater. I had replaced the starter because the old on had refused to fully engage into the flywheel. After replacing it it worked fine for a few months and started doing the same grinding sound again. I took that starter back thinking it may have been defective. After replacing s new one again It did it again after one day plus it kept on going after turning off the key. To stop the grinding I quickly disconnected the battery. I still kept on going when ever I reconnected the battery. what is going on?

View 5 Replies

Ford - Ranger :: 1990 - Headlights Becoming Dimmer

I have a 1990 Ford Ranger with 216K miles. Over the last few years, the headlights have become dimmer and dimmer.

View 7 Replies

Ford Ranger / B-Series :: 1990 - CEL Only On At Idle

I recently acquired a 4.0 Ranger 4X4 Auto for my use in Costa Rica. It runs fine but it'll illuminate the CEL within a few seconds of starting and whenever revs fall below approx 1000. When pulling off the line or accelerating, the light will go out but comes back on when the throttle closes. The previous owner has replaced the MAF and idle air valve. I've corrected a lot of issues with the vacuum system and think it's back where it ought to be. I know I am going to need to pull the codes but I'm back in Dallas now and can't do it yet. Need general list of affected parts that I could buy here and take back down.

View 14 Replies

Ford Ranger / B-Series :: 1990 - Overheating While AC Is On?

I got a 1990 Ranger 4x4 2.9l that loves to get hot only when the ac is on. The engine was rebuilt by me about 2000 miles ago and I made sure to have the block boiled in order to clean out any crap that could've been built up in the water jackets. So far the radiator, cap, thermostat, and fan clutch have been replaced. The fan shroud is intact and the condenser has a few bent fins but not many.

Here in Vegas we're looking at 100+ from 10 am - 4 pm so the ac is a must. I could be sitting at a light all day with the ac turned off and the truck doesn't have an issue. When I turn the ac on though the truck almost immediately begins to get hot. The engine drops maybe 100 rpms and the voltage gauge also drops a little. At night if I'm running the ac the voltage drops to what looks like 10 volts.

While the ac is on there is an immediate loss of power as well. In my head I'm thinking a failing compressor, water pump, and alternator are at fault. It doesn't matter if the truck is moving either, the temp still climbs.I know the rangers are funky with their cooling so when I burped the system i turned the heater on and lifted the front end about 1 ft off the ground with the cap off.

View 14 Replies

Ford Ranger / B-Series :: 1990 - No Spark And Not Starting

1990 ranger 2.9 ... I have put about everything new on this ranger. It has no spark, ran fine til i went across a set of railroad tracks, it died 6 months ago and never started again .. Many dollars and many hrs has gone into this thing and still no spark. It will spark when you turn the key on. Crank it and 3 more sparks and thats it. Every electrical piece has been replaced. I've checked and bought relays ,fuel shut off, new distributor pickup coil, rotor, cap, wires, plugs, coil and still no start?

View 6 Replies

Ford Ranger / B-Series :: 1990 - Can Convert 4x4 Transmission To 2x4?

I have a 90' Ford Ranger, rear wheel drive.

I can not find a 2 wheel drive automatic transmission and I was wondering if I can convert a 4 wheel drive transmission?

View 3 Replies

Ford Ranger / B-Series :: 1990 - TC Lockup Was Working Now Won't Lock

Just picked up a 90 Ranger last night, 4.0 EC, good ole A4LD, from a recipt I found has 70K or so on rebuild, was driving it today and the TC unlocked, and now it won't lock back up. I checked fluid and it was a little low, topped it off and drove it, and it was the same thing. I'm kinda new to thease A4LDs I know they can have issues, but can be good too. Just want to know whats going on so I can fix it! No codes were found when I scanned it. Trans otherwise shifts fine, you can feel it go into OD but no lockup.

View 13 Replies

Ford Ranger / B-Series :: 1990 2WD - Speedometer Stopped Working

I have '90 Ford Ranger 2wd standard cab long bed. A few days ago the speedo stopped working. What is the more likely cause? The gauge itself or a relay/cable. And if it is the cable/relay are they hard to remove & replace.

View 1 Replies

Ford Ranger / B-Series :: 1990 - Hesitates At Start Up Like Not Getting Fuel?

Mine has a strange issue. 1990 xlt 2.9L manual 4x4. When first start of the day, after start I push accelerator and it has a hesitation like not getting fuel. Where start?

View 1 Replies

Ford Ranger / B-Series :: 1990 - Front Transmission Seal Went Bad

I've got a 1990 ford ranger 4.0 auto trans front transmission seal went bad, I've got everything unbolted abs ready to come put but the trans won't come over top of the front cross member, what could be the problem on why it won't come out?

View 3 Replies

Ford - Ranger :: 1990 - Voltage Gauge Will Flicker And Jump Around When Starting

We have a 1990 Ford Ranger - 2WD 4cyl - sometimes when we try to start it, it will not kick over the final time for several tries. When it finally catches the voltage gauge will flicker and jump around. When the gauge flickers, the truck will shut off...then the same issue with trying to start it again. Some days it runs just fine and others it will stall out 3-5 times in a 15-20 minute drive. We have been told it's the DIS Module OR the Crankshaft Position Sensor OR the Voltage Regulator OR .....

View 2 Replies

Ford - Ranger :: 1990 - Replacing Washer Pump Pull Reservoir?

1990 Ranger 2.3 liter. Need to replace washer pump, do I need to pull the reservoir to do this?

View 1 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved