Ford - Mustang :: Replaced Clutch Now Car Won't Shift Into Gear
Sep 1, 2016
So I just put a new clutch in my 01 Mustang with the baby 3.8l engine and a 5 speed T5OD transmission. The car will shift through all gears fine when turned off, but when I start it in neutral and push the clutch in, it won't shift into any gear. I can start it in first gear though with the clutch pedal in and it moves forward VERY slowly. The trans has enough fluid, and I already pulled up on the pedal to self adjust. Not exactly sure what else could be wrong.
View 19 Replies
Advertisement
This is on an 01 Mustang with the baby 3.8l and a T5OD tranny. I installed a new clutch and now when the car is on, it won't shift into any gear. But I can start the car in gear and let go of the clutch and it moves forward just fine. I took everything back apart and checked the clutch plate and it is in there correctly. The clutch fork is completely on the little pivot ball.
The throw out bearing is the same size and everything as the old one. I pulled up on the clutch pedal to self adjust. Still not going into gear when the car is on.
I have heard that I might have air in my clutch line. But this clutch is cable actuated, not hydraulic. I have no master cylinder. Like I said before, I already pulled up on the clutch to self adjust and still no luck.
View 3 Replies
My manual 2004 Ford Ranger XLT (4.0L) has been Buzzing/Rattling. (VIDEO LINK BELOW) She has 112k miles on her. Owned 1 month, no issues when I bought from my paps. Its my 1st manual so may have been a little hard on clutch 1st few days. Noise started abruptly 1 week ago when I engaged clutch to shift to 3rd. Its gotten worse over the few days and happens even when in gear. Its much more prominent from outside passenger window. Don't notice for 1st couple mins of driving & is intermittent but often. Noticeably louder when foot is taken off gas in motion. Does not make noise when idling. Generally only above 1500 RPM . Not coming from the back half so I don't think its the exhaust/heatshield
Heres the sound......
View 4 Replies
I have my suspicion about what is the culprit, and well, the likelihood of it contuing to work.
Occasionally when I am at a stop and try to shift into gear with the clutch depressed to the floor, it does not want to go into gear. So far, I have been able to wiggle the shifter around, try a few different gears then go back to first and it works. Also at a stoplight today, with the clutch depressed to the floor for a few minutes with the car in 1st, after about 3-5 minutes the car started to slowly creep forward.
What are your suspects on this one?
View 10 Replies
Replaced Troque Converter, Truck runs engine runs fine transmission won't shift out of 1st gear.
View 2 Replies
My buddy has a 2000 1.8t 5 speed wagon, it got towed the other day and now it is having issues shifting. I doubt that it is related to the towing. If you start the car in neutral, you cant get it to shift into any gear with the clutch pressed. Even if you try to shift with the clutch not pressed, it physically wont go into gear, it wont even grind. it just wont go.
However, it goes into gear with the car off. Your an start the car in gear with the clutch pressed, and can drive as normal....until you need to shift. at which point, it does as described above. He had a shop tell him that the clutch is bad, but it does not slip. I was thinking perhaps the shift linkage, but I don't know a whole lot about these transmissions, I am only well acquainted with mk2/mk3 style 020's.
View 4 Replies
Just went to leave my apartment and I get at the first traffic light and put it into neutral. Light turns green and I try to put it into first and it won't let me... In fact I cannot shift into any gear while the car is started. Put the flashers on and I am stumped. There was also more resistance in the clutch pedal as soon as this happened.
I turned the car off and tried wiggling it into any gear. For some reason while the car is off I can put it into any gear. So I had to put the car in first gear and start it and limp it home. I had to rev the engine to about 2,800 - 3,000 RPMS in order to get the car to bite and take off. Shifting into any other gear while driving was a hassle and it felt like there was a lot of resistance.
Just did some quick Vwvortex recon and some people are saying that it is a broken pressure plate? Pressure plate welds itself to the clutch? Or possibly a throwout bearing? Also what Transmission is in a 2003 Passat 1.8T Engine code AWM.
View 2 Replies
I just rolled over to 90,000 miles on my 2002 Accord. Its running beautifully, however every so often the car "rumbles" or "shudders" when I'm releasing the clutch after I shift into second gear, or sometimes it'll do it when I'm facing up a hill pulling into first gear letting out the clutch. Its almost as if the clutch rapidly grabs then slips a bunch of times, similar to if it was warped. It doesn't completely slip at all to my knowledge. The car was bought new by my family and has been driven pretty carefully since (although 2 people have learned to drive stick on it, and my dad isn't the most "gentle" driver in the universe). I know that Clutch rebuilding and replacing is a big expensive job and its something I wouldn't even consider doing myself. So, when is it time to really seriously consider dropping down the serious cash to get the clutch rebuilt? To be honest, the shuddering is really annoying (it doesn't happen all the time though) but its something I could live with for a bit.
View 8 Replies
I have a 1966 Ford Mustang 2 + 2 (289 cu. in.) V8 with four barrel carburetor. It has more than 170K miles on it. It starts right away, but when I shift the automatic transmission to reverse or forward it dies out every time. I changed the fuel pump and the fuel filter, but the problem persists. I have had this car for almost 46 years now and I cannot bear to part with it.
View 2 Replies
My son has a Mustang GT 5.0 that is overheating. I replaced the radiator with a heavy duty 3 core radiator. It had underdrive pulleys so I replaced them with stock pulleys. I put dual electric fans on it. I flushed the block and put a new thermostat and replaced all the hoses (made sure the bottom radiator hose had wire in it so it wouldn't collapse). I put a new water pump and drive belt but it still overheats when sitting in traffic and overheats when driving with the A/C on.
View 14 Replies
My 1993 Mustang GT 5.0 will not go in to 2nd gear. It's the AOD and it goes into 1st, 3rd and OD just fine. I've heard there a pressure bolt that set the pressure in the trans and that it may be why I can't go into 2nd. And I've also heard that my TV cable may be stretched.
View 1 Replies
I had the car worked on a while back. They replaced the clutch and the viscous coupling in the transmission. ('03 Subaru Legacy manual transmission) Things seemed fine, then I realized my reverse light was acting like it was going out. Fuses are fine. A while later the car decided the clutch didn't need to respond as smoothly. Then: "Nope, you're funny to think you can drive me. I'm not budging." The car started grinding gears. I have to slam it into gear for it to work so I can drive it home and let it sit. The car will go into gear when off, no problem. New fluid has been put in. Bled. Then some sort of SUPER LUBE was put in and it still grinds. What might be happening? I really don't have the fundage in order to buy a new car at this time. But at the same time I hate feeling like I'm chasing a rabbit down a hole..
View 4 Replies
I recently had the clutch replaced in my son's 2003 Mustang and when I got it back it had a vibration in 5th gear at 60mph and in almost every gear when you let off the gas and decelerate while it is still engaged. It levels off an then as the car starts to slow down because of the engine and I get a vibration that feels as if is coming from underneath the car. I had them turn the drive shaft 180 degrees but no change. As an example, in 3rd gear while decelerating with the clutch engaged the vibration comes in about 40mph. If you disengage the clutch all vibration ceases.
View 3 Replies
I have a 2006 Mustang (manual 5 speed) that recently has been having a problem getting into 1st gear
Symptoms:1. When the engine is cold, there is no issue getting the car into gear2. Once it warms up (after approx. 20 miles or 30 minutes driving), it is very difficult to get into 1st gear. I have to put it in 2nd then get it to slip into 1st.3. On hot days the problem starts sooner and is hard to get into the other gears4. when the car has warmed up on a cool day. I can get the car into the other gears (2nd, etc) when standing still, but first is almost impossible
Originally the problem showed up when my wife drove the car, but it is getting worse. Why the engine and/or outside temperature would affect how my I can get my car into gear?
View 6 Replies
I have a 2003 Mach 1 Mustang, ( 4.6 DOHC 32 Valve)....
When I start my car in the morning. Idling the car sounds normal and perfect with my SLP exhaust. But when I start to go on my merry way, when I’m in 1st and 2nd gear and I accelerate past about 2.8K rpm's. I hear a really quite noticeable pingy/tingy sounds from my engine (Yes sounding like that annoying AMMCO commercial with people making noises). This will continue for a little while when i get into my normal running temperature, the sound isn’t as "Loud" so to say but still present.
I can comfortably say that there is nothing loose within the engine compartment. My spark plugs are tightened to the proper amount. I experience no performance lost as well. This has just been a nuisance since I have purchased the car, it currently has almost 60k mileage and has followed the proper maintenance.
View 9 Replies
I have been having an issue with my 4-5 gear shift under hard acceleration and know that a rebuild is due soon but I was wondering if any high performance kit available with all the clutches and friction discs needed to rebuild.
View 6 Replies
I replaced the fan clutch and thermostat on my 1999 5.4. Do I need to "burp" the system or anything?
View 1 Replies
I replaced the clutch, slave, flywheel and pilot bearing. Now it sounds like gravel bouncing around under the truck.
Everything works beautifully, but there is horrible noise especially at idle. If push the clutch it will quiet a little. If I change the rpm it will get worse then quiet out then get loud again, there is a sweet spot.
What the heck did I do wrong. It's a horrible gravelly grinding sound.
View 7 Replies
I recently purchased a 2000 Expy 5.4 with AWD. The issue is when in Drive it is only in 1st. I can manually shift it to 2nd. If I get it up to 40 and shift it back to drive it just reeves if I am going 30 and do that it throws it back in 1st.
So I searched a lot of the forums, I asked the previous owner some questions. Been 80 to 90k since the last tranny fluid change. Said he tighten the shift cable when it first noticed it was not shifting right and then it started to shift hard (squeal the tires). I ordered a rebuilt valve body assembly, came with plate, solenoid, accumulator and valve body. The supplier indicated this was the fix for my symptoms.
I dropped the pan. A bolt from the solenoid was in the pan. No magnet. The oil smelled more like axle grease, but did not really see signs of metal sludge in the pan or filter. Dropped all the components, yeah that accumulator plate is not for the faint of heart, I found all the rubber fortunately.
I found a couple decent pictures showing where they go in the tranny, the plate pictures were missing to many of the 'other' holes to use that as a guide. I saw a comment to use petroleum jelly to hold in place, I used that trick and it seemed to work. Put everything back together, torqued all the valve body nuts and bolts to 8 ft lbs, figure that is approx. 96 inch lbs and in the 80 -100 recommendation, new filter. Added 8 qts of oil back into the pan.
With it still on the stands started it up and went thru the gears down and up stopping in each one. Set it down and went for a test drive. Same exact behavior. Drive is first, can manually upshift to 2nd, put back in Drive at a slow speed and it goes to first, at a high speed it acts like it is in neutral. What I missed, do I have a clutch problem, or ?????
View 9 Replies
My Ranger had been shifting hard for quite awhile. I recently opted to go ahead and replace the clutch, throwout bearing, had the flywheel turned and replaced the pressure plate.
This just seemed to make the problem slightly worse. I thought it was possible that my master cylinder needed to be replaced (the slave was replaced two years ago and didn't appear to be leaking when I had the tranny off). I replaced the master cylinder and now the clutch won't disengage at all. I've spent several days trying different things to bleed the clutch, and I just can't get it to bleed. I took it back off and bench bled it, then put it back on and bled through the whole system. This isn't working. I've tried numerous suggestions-jacking up the back end of the truck, jacking up the drivers side of the truck, I even bought a vaccuum bleeder and used it for 2 hours just having an assistant fill up the reservoir while I sucked fluid out the bleeder valve. The best I could ever get was some resistance on the pedal, but not enough to push the disc away from the flywheel.
I took the pickup to Ford, they said they bled it and charged me 90 bucks and still couldn't get the clutch to release
View 3 Replies
I have a 76 f250/460 engine. I have replaced the hoses, belts, water pump, fan clutch, flowed the radiator and it still overheats.
View 4 Replies
