Ford - Mustang :: 2004 V6 Auto - Rumble-strip Like Vibration At Speeds Between 35 - 55 Mph
Jul 29, 2013
I recently bought a 2004 Mustang convertible V6 auto with 180K miles to be my daughter's first car. The car has a driveability issue. It has a "rumble-strip" like vibration at speeds between 35-55 mph. This is when accelerating or decelerating. If I slip the car in neutral when driving the vibration is gone. Here is what I have done: new plugs, wires, coil. New u-joints. Front end needed a new tie rod end on right side, new transmission filter and fluid (only replacing lost pan fluid). Another thing wrong with the car (possibly related?) is that the ABS & traction control lights are stuck on indicating a system failure with the ABS.
Note that when replacing the ujoints I noted a couple of things:1- there is SOME amount of play at the transmission tailshaft bushing. It seemed excessive to me, but a local transmission shop told me that if it is not leaking fluid that it is not a problem. I did not gage the movement, but it was close to 1/16".2 - The other thing I noticed is that the universal joint for the rear yoke was a little bit stiff, meaning that it did not move as easily as I would have thought that it should. This was the case with both the old rear u-joint and the new, This indicates to me that the pinion trunnion ears are not perfectly aligned, but not sure what I should expect.
View 18 Replies
Advertisement
I have a 2004 Mustang convertible V6 auto with 140K miles. The car has a rumble-strip like vibration that will come and go at any speed. But seems to be most noticeable at highway speeds when the car hits a ruff spot in the road. It will rumble for a short while the gradually go away. It can be more pronounced sometimes than other times.
The car did hit a curb with the right side front tire, enough so that the tire had to be replaced and did scuff up the wheel pretty good also. Had the one tire replaced, all tires balanced and rotated. Front-end alignment done.
Engine and transmission both seem to operate smoothly. New plugs, wires and throttle body cleaned. New brakes all four. I have noticed the ball joint on the front right does have a small amount of play?
View 11 Replies
I am experiencing a slight rumble-strip-like vibration/noise when veering to the right. There is no noticeable vibration when driving straight or to the right - sounds like it's coming from the front. I thought it was my tires but had them rotated with same symptoms/ I first noticed this shortly after I had them rotated in July. So it's probably front suspension.
View 3 Replies
My 2001 Outback has developed a problem in the last few days. When I move the car from a dead stop, I go through a brief period of heavy vibration coming from the back of the car, exactly as if I am running over a rumble strip. It occurs as I am accelerating away from the stop just after the clutch is totally let out. Once I get to a high-enough velocity, I no longer feel it. However, if I maintain a very low velocity I can feel some vibration but not quite as pronounced as it was coming from a dead stop.
I have been able to make this happen in 1st and 2nd gear, I have not tried in 3rd, 4th and 5th. It does not happen in reverse. I tested the clutch by putting the car up against the back wall of my garage, revving the engine and putting the car into 4th and 5th gear and the car stalled, as it should. The clutch did not slip. This clutch has about 60,000 miles on it. The previous clutch was replaced at about 85,000 miles. The problem has been getting worse steadily during a just completed a 700 mile holiday round trip. Could this be the clutch? Could it be something in the transmission?
View 5 Replies
Care finally runs well and passed inspection. So I can legally drive it at speeds. Noticed what feels like widely space rumble strips when coasting 2003 explorer. I am now trying to check all my fluids ... trans seemed a bit low (PITA), rear and front differentials seemed full... but should they be checked with the engine running or off??
View 14 Replies
My '05 Expedition will be driving normal at highway speeds, and when I need to apply a little more throttle to start up a hill I get a shutter thru the truck that sounds and feels like driving over a rumble strip. It doesn't last but just a second or two, but it happens frequently. Is it something in the 4wd? Transmission? or.......?
View 3 Replies
My vehicle had a shudder which felt like driving over a rumble strip. It would usually occur after hitting a small bump at around 35 mph and hearing a clunk underneath. The shudder lasted just a few seconds. Checked the whole steering, suspension, chassis, drivetrain, u-joints, rear e-brake shoes etc. Finally found that the RF axle shaft could be moved up and down excessively in the steering knuckle. Removed axle shaft, R&R u-joint, vacuum hub seal and the torrington bearing in the hub. (used to call it a spindle bearing) ...
There was a little bit of wear into the stub shaft where the spindle bearing rides. That removed the play from the axle when it was all re-assembled. I was very happy until about a month later when it started doing it again, but not as bad as it was originally. I think maybe the stub end of the axle shaft needs to be replaced due to the wear in it. I don't want to just throw a somewhat expensive part at it without some info about "superduty shudder".
View 1 Replies
Today and yesterday day mark the first time since I have owned my truck, that I have really taxed it with a load or serious work.
I have 8126, miles to date, and hadn't felt this annoying and somewhat pronounced shudder at throttle- tip in. Only from a dead stop. I'm doing some work to my house, so as I type this I have about 700-800lbs in my box. I've never felt this shudder empty as I do with a load, and starting out on an incline.
It feels like the rear is rolling over a "rumble strip" for the first few feet of throttle input, between 5-10 mph and then smooth everywhere else.
Rob- if your reading this, I can't remember if your shudder was similar, or if yours did it empty or only when towing or hauling a load.
View 14 Replies
I have a weird problem with my 2008 Elantra GLS 86K Miles on it. I did a couple of searches on this problem but didn't find any threads. About a month ago I noticed that when I braked hard at highway speeds 65 to 70 Mph I would get a noise that sounded like I was driving over the rumble strips on the side of the road. The rumble was the same frequency no matter what speed you are going, it doesn't get faster or slower. The problem slowly got worse to the point that it would happen at 25 to 30 Mph. The noise sounds like it is coming from the front but I can't tell which side. I figured that it was probably rotors and time for a brake overhaul so I replaced the rotors, pads and hardware on the front and the back. I used synthetic brake grease on the slides and guides. I also replaced the brake fluid with synthetic DOT 3.
When I did the back brakes I found that the wheel bearing on the passenger side was leaking lots of grease so I replaced it with a Timken bearing. (I live over an hour away from the nearest dealer so I did the repairs myself.) While I was working on the bearing I pushed the rear shock up and out of the way and it stayed in the up position for quite a while, aren't the shocks under pressure and usually push right back down? (Just an off subject thought) Well after replacing the bearing the rumble strip noise went back to just happening at speeds from 45 Mph and up. I was also thinking of pulling the fuse on the ABS and seeing if the problem goes away but will pulling the fuse hurt the car in any way or trip a code? I know what the ABS sounds like and this is not the same noise you get when sliding on ice.
View 22 Replies
When my 2004 jeep liberty sport goes between 40 and 50 miles an hour it sometimes shakes like it is going over a rumble strip if i release the gas pedal it stops was wondering if it was some sort of trans sensor that was starting to go bad ...
View 3 Replies
Have a 02 v10 125xxx miles have had grinding noise on drivers side sounds like driving on rumble strip took out the unit hub everything looks good changed out the needle bearing because it was frozen still have sound after needle bearing replacement sound goes away if hubs are locked so question is it the unit bearing or stub shaft...
View 2 Replies
My wife drives a 2006 Honda Civic. She just drove back from Vermont - we live near Boston - and on her way back the idle was unusually rough and twice she said it felt as if she was driving over rumble strips, even though she was on smooth pavement. The first time she was going 40 and the second time she was barely moving. She also noted that once, at a stop sign, the car wouldn't slowly move forward when she took her foot off the brake, as it usually does. She had to give it gas. The thing is, the problem is very intermittent.
She says the only thing that is constant is the rough idle, but the engine check light is NOT on.
The last work that was done on the car, about a month ago, was the replacement of the calipers and shoes on one of the brakes. My wife had driven for some time with the squealing noise that indicates you need to change your brake shoes without telling anyone about it. She used the radio fix.
View 7 Replies
I recently had u joints and left front wheel hub assembly replaced at a local mechanic. Ever since I have a vibration between 40-45 and 52-62, the vibration can be felt in the steering wheel, the seat and the floor. The mechanic claims I need a new driveshaft as some of the counter weights were starting to rust. I indexed and removed the drive shaft and had it rebalanced at a local machine shop. This did not solve the vibration problem. There is also a transmission leak starting from the extension housing. How I can start to trouble shoot the problem. 04 F150..
View 2 Replies
I have had a 2004 Extended Cab F150 5.4L for a few months now. It just started vibrating at speeds between 15 and 30mph on accelerating or deceleration. Doesn't matter if I'm turning or going straight, just those speeds. It's fine otherwise. I put it in gear and held the brake down and brought the rpms up to 3000 to see if it would shake with a load, thinking a possible misfire, but nothing abnormal.
It's an automatic transmission. I started off in 1 and 2 and it seems to lack power until it shifts to 3rd gear - which is about 30mph. It also seems to lack power in reverse ... no slipping, but seems to have to give a lot of gas in order to go over the slightest incline backing up.
View 1 Replies
My 07 AT 2.0 has a weird problem - when auto downshifting after a long drive at highways speeds, the whole car thuds. This happens after driving about 20 miles or so at 60MPH+. 5 or 10 miles are not a problem.
What happens is that when it slips down into 2nd, it sounds like something jams (no grinding). The force/feeling is similar to running into something at a slow speed - like bumping a car while parking.
If I slip into Tip and downshift manually, it doesn't happen. Outside of this the car has 22K miles and drives great.
View 8 Replies
I have a 2007 F150 (2wd) with 80k. My truck recently was vibrating under braking so i took it to my mechanic to have the brakes fixed. All the rotors needed to be replaced. In doing so, the front rotors were changed out with the kit that converts the front rotor/bearing assembly into two separate pieces to cut down on maintenance costs in the future. With this being said, after getting this work done, the truck didn't vibrate anymore... that is until i got it out on the highway. Now the truck vibrates from about 45-50 and 70-80 pretty bad. The steering wheel shakes back and forth too. I have gotten the tires balanced in hopes to fix this problem which it didnt. What could this problem be?
View 4 Replies
I recently had the clutch replaced in my son's 2003 Mustang and when I got it back it had a vibration in 5th gear at 60mph and in almost every gear when you let off the gas and decelerate while it is still engaged. It levels off an then as the car starts to slow down because of the engine and I get a vibration that feels as if is coming from underneath the car. I had them turn the drive shaft 180 degrees but no change. As an example, in 3rd gear while decelerating with the clutch engaged the vibration comes in about 40mph. If you disengage the clutch all vibration ceases.
View 3 Replies
I hooked up the boat and went out for a tow. I ended up getting a pretty good vibration and thought maybe it was time for balancing the trailer tires. As it turns out I needed two new tires as they were at the wear bars (cheap crappy bias ply tires) so I ended up buying 4 trailer tire radials and had them balanced.
As it turns out I have what I guess is a shudder at slow speeds and also can feel it at other speeds as well. A way to explain it is that it sort of feels like you are driving over the rumble strips on the side of the road but really small ones.
View 14 Replies
I have a 2014 V6 Mustang. Recently I've begun to smell that special scent of burning metal intermittently, more often at slower speeds or when stopped completely. In addition I've noticed that my mileage has been dropping a bit and that the car doesn't pick up quite as fast as it used to. Today on a hunch I put the car on a non-incline surface and let the clutch out relatively quickly. I was shocked to discover that it didn't stall - it absolutely would have when it was newer. The brakes also don't appear to be shedding dust so I don't think one of them is locking up.
Normally these would be signs of a clutch going bad. I'm suspicious because my car only has 25,000 miles on it. It has been driven through two Michigan winters and thus subjected to some abuse, but even if I were riding the clutch daily (I would never) I would be surprised to see it go out so young. Should I be looking at something else, or should I just break down, go to the dealer, and fight with them until they replace it?
View 10 Replies
On my 07' I bought it home mid AUG. It has been getting much worse to a point there is a rear driveline vibration at all speeds above 40 and up to 70. I used to change intensity whether you are on or off the gas, and would almost vanish if in neutral. However now it is all the time.
I cannot feel any play on the u-joints, the yoke has a little play in the xfer case but is is normal like on most other trucks I have owned, and the pinion flange is nice and tight. Could this be **tight** ujoints or the driveshaft itself? It looks rusty, but there are no dents on it.
View 4 Replies
First, details about my truck. 2007 F150 SuperCrew, 2wd, 5.4, 203,xxx miles on it, leveled with Hell Bent Steel 2.5" kit last year, has been aligned professionally since then, tires are good and balanced.
The issue I have is a vibration, kind of the same feeling when driving on a road surface that has had the top level of asphalt removed before it's resurfaced. It's mostly noticable at highway speeds. Its not a violent type vibration, but you can feel it. There is also a sound, similar to tires with a deep off road type tread.
The sound and vibration more noticeable when making lane changes or when wheel turned towards left, at highway speeds, not as much to the right. I've checked front wheel bearings, they are good, zero play, no loose suspension parts, u-joints are good, no leaks anywhere.
Since it makes the noise and vibration a bit more when moving wheel, could it be a power steering pump? The pump is the original.
View 1 Replies
