Ford - Mustang :: 2001 Won't Shift Into Gear After New Clutch Installed
Sep 2, 2016
This is on an 01 Mustang with the baby 3.8l and a T5OD tranny. I installed a new clutch and now when the car is on, it won't shift into any gear. But I can start the car in gear and let go of the clutch and it moves forward just fine. I took everything back apart and checked the clutch plate and it is in there correctly. The clutch fork is completely on the little pivot ball.
The throw out bearing is the same size and everything as the old one. I pulled up on the clutch pedal to self adjust. Still not going into gear when the car is on.
I have heard that I might have air in my clutch line. But this clutch is cable actuated, not hydraulic. I have no master cylinder. Like I said before, I already pulled up on the clutch to self adjust and still no luck.
View 3 Replies
Advertisement
So I just put a new clutch in my 01 Mustang with the baby 3.8l engine and a 5 speed T5OD transmission. The car will shift through all gears fine when turned off, but when I start it in neutral and push the clutch in, it won't shift into any gear. I can start it in first gear though with the clutch pedal in and it moves forward VERY slowly. The trans has enough fluid, and I already pulled up on the pedal to self adjust. Not exactly sure what else could be wrong.
View 19 Replies
My manual 2004 Ford Ranger XLT (4.0L) has been Buzzing/Rattling. (VIDEO LINK BELOW) She has 112k miles on her. Owned 1 month, no issues when I bought from my paps. Its my 1st manual so may have been a little hard on clutch 1st few days. Noise started abruptly 1 week ago when I engaged clutch to shift to 3rd. Its gotten worse over the few days and happens even when in gear. Its much more prominent from outside passenger window. Don't notice for 1st couple mins of driving & is intermittent but often. Noticeably louder when foot is taken off gas in motion. Does not make noise when idling. Generally only above 1500 RPM . Not coming from the back half so I don't think its the exhaust/heatshield
Heres the sound......
View 4 Replies
I have my suspicion about what is the culprit, and well, the likelihood of it contuing to work.
Occasionally when I am at a stop and try to shift into gear with the clutch depressed to the floor, it does not want to go into gear. So far, I have been able to wiggle the shifter around, try a few different gears then go back to first and it works. Also at a stoplight today, with the clutch depressed to the floor for a few minutes with the car in 1st, after about 3-5 minutes the car started to slowly creep forward.
What are your suspects on this one?
View 10 Replies
My buddy has a 2000 1.8t 5 speed wagon, it got towed the other day and now it is having issues shifting. I doubt that it is related to the towing. If you start the car in neutral, you cant get it to shift into any gear with the clutch pressed. Even if you try to shift with the clutch not pressed, it physically wont go into gear, it wont even grind. it just wont go.
However, it goes into gear with the car off. Your an start the car in gear with the clutch pressed, and can drive as normal....until you need to shift. at which point, it does as described above. He had a shop tell him that the clutch is bad, but it does not slip. I was thinking perhaps the shift linkage, but I don't know a whole lot about these transmissions, I am only well acquainted with mk2/mk3 style 020's.
View 4 Replies
Just went to leave my apartment and I get at the first traffic light and put it into neutral. Light turns green and I try to put it into first and it won't let me... In fact I cannot shift into any gear while the car is started. Put the flashers on and I am stumped. There was also more resistance in the clutch pedal as soon as this happened.
I turned the car off and tried wiggling it into any gear. For some reason while the car is off I can put it into any gear. So I had to put the car in first gear and start it and limp it home. I had to rev the engine to about 2,800 - 3,000 RPMS in order to get the car to bite and take off. Shifting into any other gear while driving was a hassle and it felt like there was a lot of resistance.
Just did some quick Vwvortex recon and some people are saying that it is a broken pressure plate? Pressure plate welds itself to the clutch? Or possibly a throwout bearing? Also what Transmission is in a 2003 Passat 1.8T Engine code AWM.
View 2 Replies
I have a 2001 EX we did a little mudding and now its not shifting into 4th. We have flushed the trans and no shaving or anything. A few told us to change the speed sensor.
View 1 Replies
I just rolled over to 90,000 miles on my 2002 Accord. Its running beautifully, however every so often the car "rumbles" or "shudders" when I'm releasing the clutch after I shift into second gear, or sometimes it'll do it when I'm facing up a hill pulling into first gear letting out the clutch. Its almost as if the clutch rapidly grabs then slips a bunch of times, similar to if it was warped. It doesn't completely slip at all to my knowledge. The car was bought new by my family and has been driven pretty carefully since (although 2 people have learned to drive stick on it, and my dad isn't the most "gentle" driver in the universe). I know that Clutch rebuilding and replacing is a big expensive job and its something I wouldn't even consider doing myself. So, when is it time to really seriously consider dropping down the serious cash to get the clutch rebuilt? To be honest, the shuddering is really annoying (it doesn't happen all the time though) but its something I could live with for a bit.
View 8 Replies
I have a 1966 Ford Mustang 2 + 2 (289 cu. in.) V8 with four barrel carburetor. It has more than 170K miles on it. It starts right away, but when I shift the automatic transmission to reverse or forward it dies out every time. I changed the fuel pump and the fuel filter, but the problem persists. I have had this car for almost 46 years now and I cannot bear to part with it.
View 2 Replies
I have a 2001 Ford F-150 5.4L Supercrew that won't seem to shift out of 1st gear. This morning coming out of stop light on the way to work, the truck seemed to jerk when it was supposed to shift into 2nd gear. I was told by a friend that the speed sensor may be it?
So I took the truck around the block just so I can get a feel for what is going on. So the truck shifts into 2nd, but not past that. It seems that around 30mph the RPM's go up jump up quickly to 2k+ and no shift or increase in speed. I was reading up a bit on it and came across the possibility of a TPS?
View 5 Replies
Just installed new clutch and everything good except pedal doesnt comecall way up now have pull up with foot, ans grabs rt off the floor, i assume just need to adjust? Make adjust rod longer?
View 10 Replies
I have a 2001 ford f150 4x4 xlt and it seems to be shaking violently in first gear when I try to release the clutch slowly. The person i bought it from said he had a new clutch put in this year So i don't think its the clutch. What could be the cause of it before I take it in to be checked.
View 2 Replies
I just bought a f150 2001 5.4L crew cab. It has the O/D switch in the gear shift lever and the black plastic handle is broke. I found a complete replacement lever on ebay but cannot find any tutorials on how to replace this.
View 8 Replies
My 1993 Mustang GT 5.0 will not go in to 2nd gear. It's the AOD and it goes into 1st, 3rd and OD just fine. I've heard there a pressure bolt that set the pressure in the trans and that it may be why I can't go into 2nd. And I've also heard that my TV cable may be stretched.
View 1 Replies
The other day I was driving i was driving down the road when suddenly my truck wouldn't shift out of first gear, then the truck died and the motor wont turn over either. Acts like it is locked up. Its an 01 with v10 and 4r100.
View 6 Replies
I may be going to look at a 2001 F250, 4x4 with a V10 engine tomorrow. I think it is a shop truck for a business. The owner said that the mechanics told him that the trans won't shift out of low gear. It is an automatic. Maybe something as simple as a modulator valve (do they still use them)?
View 4 Replies
I recently had the clutch replaced in my son's 2003 Mustang and when I got it back it had a vibration in 5th gear at 60mph and in almost every gear when you let off the gas and decelerate while it is still engaged. It levels off an then as the car starts to slow down because of the engine and I get a vibration that feels as if is coming from underneath the car. I had them turn the drive shaft 180 degrees but no change. As an example, in 3rd gear while decelerating with the clutch engaged the vibration comes in about 40mph. If you disengage the clutch all vibration ceases.
View 3 Replies
i bought a f250, i rebuilt the 7.3 after installing it the transmission isn't shifting correctly. Reverse perfect, 1st and shifts to 2nd great. wont go into 3rd. i replaced the 2 sensors on the transmission, i replaces the sensor on the 3rd member. the speedometer works but not correctly, i can unplug the sensor on the front of transmission and it shifts into 3rd. but when i plug it back it doesn't. no codes. could it be the ecm?
View 10 Replies
I have a 2006 Mustang (manual 5 speed) that recently has been having a problem getting into 1st gear
Symptoms:1. When the engine is cold, there is no issue getting the car into gear2. Once it warms up (after approx. 20 miles or 30 minutes driving), it is very difficult to get into 1st gear. I have to put it in 2nd then get it to slip into 1st.3. On hot days the problem starts sooner and is hard to get into the other gears4. when the car has warmed up on a cool day. I can get the car into the other gears (2nd, etc) when standing still, but first is almost impossible
Originally the problem showed up when my wife drove the car, but it is getting worse. Why the engine and/or outside temperature would affect how my I can get my car into gear?
View 6 Replies
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission.
I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced.
I have also just had a new hydraulic clutch kit installed.
View 5 Replies
Here's the scoop: 2 year old clutch & flywheel with 21,000 miles on them. Clutch master cyl. is full & not leaking. The clutch slave cyl. moves when the clutch is pressed & is also not leaking. The shifter linkage has been checked at the shifter and moves freely as it should.
I started the car, put it in gear, let the clutch out and there is no movement from the car regardless of the engine revs. The engine runs freely and does not die with the clutch engaged and the transaxle in gear. Putting it in ANY gear (including reverse) has no effect. The car will not move.
After turning the engine off I left the car in gear, left the e-brake disengaged, released the foot brake and the car stayed put. I then put the shifter into neutral, let the foot brake off and the car began to roll. I stopped, put the shifter back into 1st, let the foot brake off and the car was again stationary and did not roll. This tells me that the shifter linkage indeed works and that the car WILL go into gear. So, why won't the car move under power?
View 9 Replies
