Ford - Focus :: 2001 - Stalling / Becoming Harder To Start And Maintaining Steady Idle
Jun 27, 2013
My daughter's automatic DOHC SE Focus had suddenly been stalling, becoming harder to start and not maintaining a steady idle. I took it to our semi-trusted repair shop and was told it needed an EGR valve, plugs, coil, and ignition wires. $580! These all seemed like repairs I could do and so I have worked through all of these. I replaced the EGR valve and that seemed to make the problem actually worse. (so I put the old one back in) I put in new plugs and that improved the idle a small amount. Then I put in the new coil and that seemed to steady the idle a bit more. But here is what I have discovered through my many test drives after making these incremental repairs: The car starts now from cold very well and runs great for the first 20 minutes or so but...when it gets hot after 15 minutes or so of 50 mph driving, the idle drops and the engine wants to cut off. At low revs it seems to stumble and lose power. I think this is what my daughter was experiencing originally and none of my early test drives were long enough to surface the original problem. I have read that the Idle Control Valve might be a culprit in this sort of behavior.
View 5 Replies
Advertisement
my 2000 focus se, 2.0L SPI, with 82k began to recently run rough at idle then progressed to stalling at longer lengths of idle. The condition starts once the engine warms after 2-5 minutes. I 1st tried gas treatment. I replaced the ignition coil as suggested in the other threads, but it has not improved the problem. I had the fuel pump recall-replaced 2 years ago. I would guess that a bad fuel pump would exhibit loss of power at all engine speeds? Before I proceed to replace plug wires and plugs.
View 14 Replies
I have a 2008 Ford Focus - 4 Door Sedan SE 60300 miles.
I've gone to 3 mechanics now and no one can seem to figure out whats wrong with my car. Here's whats happening:
About 1 1/2 years ago I took my car to get an oil change at Jiffy Lube (Yeah never again). When I left, my car was idling funny... Silly me didn't take it right back and have them tell me what was wrong.. so I let it go, well about a month later it started idling even weirder. Basically it feels like my car is shaking when it gets under 1000 RPM and I notice my RPM dial start falling and bouncing back, acting like its going to stall, but never does. I notice a loss of power when this is happening (on speed up and just accelerating in general). All of this is random, I can't seem to put a pattern to it as to when it happens. One day I'll start it up and everything is perfect... Then I'll shut it off and restart it later, and it starts vibrating and puttering again... No signals as to if its hot/cold or wet/dry, no environmental variables seem to cause it to happen anymore than others. And there is no check engine light on, everything "looks" normal.
What I've had done to it so far is:
Air filter changed / reseated
3 oil changes (keep getting told it will work)
Throttle cleaned
Computer reset for idle sensor data rebuilding
Now I'm told that I need new engine mounts, and that could be the reason for the vibration. I'm thinking that the vibration caused the mounts to wear out, more so than the mounts being the cause. Mainly because I don't see how bad mounts could cause loss in power/bad idling.
What could be wrong?!? Really bugging me and don't want to keep throwing money at it for phantom solutions. Seems like mechanics I go to can't figure it out unless there is a check engine light on with some diagnosis code to tell them exactly whats wrong.
View 8 Replies
I have a 2001 Ford Focus ZX3 (2D Hatchback) that has been randomly stalling since we bought it. There is no engine light, the dealership couldn't get it to stall and just gave it back. Another garage got it to stall and thought it might be the "idle-oxygen sensor" (not sure if I'm remembering the name correctly), but that didn't stop it from stalling either.
My wife is ready to dump it, but even spending a couple thousand a year on repairs is less than the grand total of a year's payments on a new car, insurance, etc. But it would be nice to fix it.
View 8 Replies
My 2004 Ford Focus Hatchback has 152,000 miles on it. At the end of last year the engine started dying/stalling as soon as I started it - I would have to keep my foot on the gas to keep the engine going. I took it to the dealer and they put in a WHOLE NEW THROTTLE BODY. They also told me I needed a new battery and updated the car's software. Total $700. About a week to 10 days later, the car started doing the dying out after starting thing again - intermittently - didn't matter if the engine was hot or cold, fuel high or low, weather rainy, cold or clear and warm.
This morning I worked for 20 minutes to keep the engine going, made sure the engine was warm, and it STILL stalled out. I called in for a tow, called the dealer and said I'd be coming in, went back out to the car ... and it started right up without stalling. Drove it to the dealer and they've now told me they can't find anything at all wrong with the car. They are keeping it overnight to see if they can duplicate the stalling tomorrow morning. Any thoughts? The new throttle body cost me about $500 in December. (Don't know if it matters, but the defroster fan was super loud this morning, but once the engine was able to idle, the loudness disappeared ...). It's been a great car, but maybe it's time to start looking.
View 3 Replies
I purchased a 2001 Ford Focus 7/17 from a Ford dealer. While my daughter was driving, at a left turn, the engine light came on, the car stalled, and the steering wheel and gas pedal locked up. A friend did a computer scan and said the code came back that 2 sensors, the crank shaft and cam shaft sensors, needed replaced. So we had them replaced.
About 4 days later, while driving home from school, on a right turn, the car broke down again on my daughter. She said the symptoms were the same, engine light came on, car stalled, the steering wheel and gas pedal locked up. So we had it towed to a local Ford service department. They said the ignition coils needed replaced and the valve cover gasket would eventually need replaced (per the mechanic, this wasn't directly related to the issue but a small leakage was found). So we let the Ford mechanic replace the coils and the valve gasket cover. They ran several tests and put 20 additional miles on the car without failures or issues, scans came up clean.
So while driving to school this morning, on a u-turn, my daughter experienced the issue again....car stalled, engine light came on, steering wheel and gas pedal locked up. After sitting a few minutes, the car started up so she drove it home and hitched a ride from dad to get to school.
View 6 Replies
My coworker is giving me a clean 2001 Santa Fe with 151000 miles. It was running fine then all of the sudden it lost power but was able to stutter home. I went to check it out it started fine but idled a little rough. When I revved the engine it rose to about 2500rpm and stuttered then stalled. Kind of like it was rich and choking out. It then had difficulty restarting.
View 10 Replies
2003 Ford Escape V6 ... So . . . my car runs fine almost all the time and I love it. But every couple of weeks when I start her up she won't hold a steady idle. Unless I hold my foot on the accelerator pedal she dies right out. I have had to limp home as she dies at each stop light. I have tried disconnecting the battery to reset the computer but it never seems to work. On the drive home, there will be episodes of misfiring after which the computer will reset itself. (The dash instruments go to zero and then back into normal range while I am driving down the road!) After a couple of resets, the car drives fine the rest of the way and continues fine for a couple of weeks (except for some misfiring at idle).
And at cruising speed there is a chatter behind the dash which sounds like its from the computer--very intermittent and only at around 45-60 mph--it only lasts a few seconds and goes away when I changed speed. The car is great in every other way after 104,000 miles. In the past 12 months, I have changed the thermostat, the plugs, the PCV, the fuel filter, and the air filter. A year ago both Brake Sensor rings cracked so I replaced both CV shafts. The crankshaft position sensor code came on twice and I replaced it twice. I do all my own work but I am stuck in a rut right now.
View 2 Replies
I have a really weird issue with my 2003 Ford Focus. Manual transmission, just over 50,000 miles. I've been noticing a stumble or hesitation (like the engine is cutting out) at steady speed, but ONLY when it is snowy out, more if it's windy as well. I don't recall that this happens if it's rainy or foggy. All maintenance is performed as specified, to include air filter changes.
View 9 Replies
I recently bought a 2001 Ford Focus (about 4 months ago) and it recently began having a rough idle, check engine light, and stalling. One night, I started and it immediately stalled. When I tried to drive it, it made a grinding noise. Eventually, I made it home and got it to a shop the next day. I was told that it was likely the pistons by a mechanic. He later confirmed it was the pistons, had them replaced, sent my engine off to a machine shop for "smoothing". 2 days later, I had it back and it seemed to be running great. Took it to work and went up a small grade hill (not even labeled) and it began chugging, making a grinding noise and the check engine light began flashing.
I took it back to the shop where the mechanic couldn't even keep it running and he determined that it was a broken hose. He replaced it, free of charge and the car ran great for a couple days. Next thing you know, it begins the rough idle and random stalling but no check engine light. I took it back in and he asked to keep it for a few days. He said that he determined the machine shop didn't do things correctly and sent it back in. I got it back this morning and it seemed to be running fine for my husband, but once I got in it, there was a loud rumble and a slightly rough idle. Then, there was the smell of burnt rubber. My mechanic wants it back, but isn't open again until Monday and I work the next two days. By the time I got it home from work, it had a very rough idle, issues accelerating and I'm still having issues going up hills.
Clearly, my mechanic is really focused on the issue being related solely to my pistons and is only focusing on that. I think something else is wrong and is being missed, but I have no clue what.
View 3 Replies
My wife has a 01 ford focus zx3 3 door automatic wont start she was driving and it lost power and shut down I replaced the plugs, wires, pcv hose and pcv valve, coil, fuel pump good 40psi, compression 150 to 180, even drop the converter still wont start could the injectors play a role.....
View 11 Replies
My car stalls when I come to a stop but only in warmer weather (50 degrees or higher) and only after I have driven the car for 20 minutes or so then come to a stop. There is no check engine light on, no high temperature warning. I can start it back up (not a battery problem) easily, but as soon as I take my foot off the gas to put it in drive, it stalls. However, when I've let the engine cool, it's drivable again (until I come to a stop again).
I have taken it in to the repair shop after it has done this twice. Their computer check shows everything working fine and there ar no errors. Of course, by that time, then engine has cooled and they can't reproduce the stalling. I am dreading the upcoming warm weather because it's just a matter of time before I am stranded again. I don't know what to do if I can't get a diagnosis and repair!
View 4 Replies
I have an 01' f150 that everything is going out on. I've replaced the GEM module thinking that's what it was to no avail. First thing to go was all four windows which have currently been stuck halfway down for 2 weeks. It's stalling out during idle like it isn't getting enough fuel to it. Brake and engine light on dash are staying on. Radio, interior lights won't come on. Will not come out of park once in. I have to do the old forward, back, middle key trick to get it out of park into neutral so I can start it and go. I've also checked all fuses and relays under dash and under Hood.
View 3 Replies
Why my 03 focus zx5 will stall in reverse. I have had the tranny serviced. I can drive it and then let it sit for about an hour and then try to reverse in it and it dies. I have change the mac, tps, iac sensors. I am at a loss for why this is happening. I also changed the pvc hose that runs from the back of the motor to the pvc valve.
View 14 Replies
A couple weeks ago my 01 7.3 with 265,xxx started ideling rough and stalling. I had driven in all day Sunday and the next day it started out of the blue! It would barely start idle rough and stall out no CEL. I have singed changed the icp, fuel filter and I have checked oil level. Also used fuel cleaner. Still had no luck. When I changed the icp sensor the check engine light came on and was no change I then got a ford oem camshaft sensor and my truck fired right up but still sounded like it had a little miss here and there drove it for a few weeks fine now back to the same thing it will start up and idle fine for 10 seconds then start the rough idle but won't stall out anymore just idle rough. I am stumped I can't get any codes to pull up and if oriellys uses there scan tool while the truck was running it would shut the truck off! I can't find any answers.
View 8 Replies
New here. I have a 2001 F150 which i love but lately has been an issue. I started it up a few weeks ago after it set over night. i threw it in to reverse and notice it hesitating while reversing and it has small trouble accelerating but does buck and jerk while trying to maintain speed. So I took it to my well trusted mechanic and he ran compression test and ran the highly prolific OTC scanner on it and nothing. I have changed my mass flow sensor and I dont show any misfires or any codes pending. I did replace a busted catalytic convertor a couple months back. Im running out of places to turn.
View 6 Replies
Almost every time I start my 2001 Ford Focus, it won't start. The starter functions but the engine won't start. I have to pump it, give it gas, and once it starts, it's perfectly fine, no stalling, no problems after that. That is until I turn the engine off. When I go to start it again, say after doing an errand or two, it may or may not happen again throughout the day, the problem only occurring when I attempt to start it.
View 1 Replies
I'm a diesel mechanic and know my way around Powerstrokes, this 4.0 is not what I would usually work on, but I have a friend who has 2006 explorer 4.0L SOHC, someone told him he needed a motor with out explanation why, so I didn't want to see him get ripped off. The problem is it idles very rough, hard to start, and stalls. There's no DTCs , if you hold the accelerator slightly it will stay running, but once you let off it will either idle really bad and misfire or cut off, once pushing the accelerator the rpms raise very smoothly up til 3500 which is what I assume the rev limit is in nuetral.
I've done checks with focom and forscan, I was thinking possibly a bad fuel pump, while monitoring fuel pressure I see a range of 289 - 326 kpa with 26% fuel pump I guess duty cycle would be the correct term(once again I'm a diesel guy, and use to dealing with IPRs and Hpops) not sure if the desired fuel pressure is relevant on these but it always stays at 269kpa. I believe that equals out to 40-48psi while I believe this system is supposed to have somewhere in the range of 60 - 70, but I wouldn't expect to get a rough idle with no load with almost 50 psi of fuel pressure.
So with no DTCs Im baffled, and don't want to start wasting money just throwing parts at it. I've thought everything from fuel pressure sensor, to coil pack(replaced 4 months ago) to crank and cam sensors.
I did end up getting a code p106, but I believe this is because I didnt tighten the intake hose after checking the throttle bottle, I just slid it back on. out of the 4 days of testing first time I seen a code pop up besides unplugging some sensors here and there to make sure the pcm would actually register a dtc.
View 3 Replies
I have an '01 Blazer that's had a strange vibration for some time now. Here are the particulars:
It's a low frequency rumbling It happens only between 45 and 60 mph It tends to come and go It usually starts after about 5 minutes of driving first thing in the day It generally goes away after awhile and may not happen the rest of the day It happens only when I'm accelerating or maintaining speed on an incline It happens when it's hot, cold, wet or dry
What I've done lately: replaced all the brake pads replaced one rear rotor and caliper slide pins (one pin was frozen and the rotor was badly worn Checked the U-joints, which are sound
View 6 Replies
1997 buick lesabre, 4 door, v6. It was having problem stalling out. This weekend a friend and I lifted the car and replaced the fuel filter and fuel pump. Drove great Saturday and Sunday. Today I get in the car, starts up without a hitch. I start heading down my street and realize I am having to push my brake pedal in ALL THE WAY to get it to stop and even then it's slow to stop. So I back up, pull the hood and check the brake fluid. Sure enough, it's low, so I run to Advance, grab some fluid and fill it up the max line and think i'm ok. Start the car up, pump the brakes a few time and notice nothing new. I get out and realize I have a very steady leak in front of the right rear wheel of fluid. It's a steady drip in two places. Is there something I could have done to have caused this. The only line we messed with on Saturday was the emergency brake line and it's clearly working (I tested it).
View 1 Replies
Trying to get my daughters Santa Fe going. Engine stalling. Idles very slow. 2001 model with 2.4 engine, auto trans.
Code P0102 is active. Cleared with scan tool and it comes right back.
Replaced the MAF and no change.
Checked the intake for leaks / vacuum leaks and none found.
Checked for debris up-stream from MAF and all is clear.
Air filter is clean and dry.
Checked harness plug and found the pin 5 has 4.6 volts on it from PCM. This is the signal wire from MAF to PCM. 4.6 volts is KOEO.
IS THIS NORMAL OR IS PCM BAD ??? All other pins / voltages on harness plug are normal.
View 4 Replies
