Ford - F250 :: Rough Idle - Misses For About A Mile Or So Until Temp Rises
Jun 21, 2016
2004 ford f250 superduty v10, truck has a cold run miss, no matter the temp. (0deg. or 100 deg.) when i start truck it misses for about a mile or so until temp. rises, after that it runs fine all day even if i park it for a few hours,next day same thing. I have changed all 10 plugs, gas filter, air filter, cleaned mpf censer, throttle body. Also it shows no codes, and there are no codes in history.
View 3 Replies
Advertisement
My 95 4.0 has had a periodic idle issue for quite a while. It seems it may be getting worse. Here is when it may only happen:
Vehicle is fully warm. I shut it off for about 1 hr or so and when I restart it, it shakes and misses in idle. It will idle fine after I drive it around or if I rev the engine for a while when still parked.
This never triggers the "check engine light". New fuel filter, plugs and wires.
View 1 Replies
I did an engine swap for a junkyard motor my 4.0 ohv had a very bad rod bearing so I got one from the junkyard with 117,000,or so they say.Anyhow, after its all said and done it runs perfect except the temperature gauge seems to not get as high up on the gauge as before after sufficient driving(it used to run about middle of the gauge) it drops low at idle then goes up and stays up then goes down.it still has good heat, doesn't seem as good as before tho.I changed the thermostat also.
View 8 Replies
When I put my foot down in 4th 5th and 6th gear my clutch slips badly but when the temp rises all is fine?
I only have 135k and no oil leaks, however my VF mounts are done could it be the engine moving a lot and slightly depressing the clutch?
View 1 Replies
I have a 1992 Chevy 1500 5.7L V8 with 167,000 miles that is running hot. When I drive the vehicle the temperature quickly rises to just about 250 degrees and hovers just under the "red" zone. It never fully overheats, even on longer drives (50+ miles). It seem to run just fine otherwise. It is not leaking coolant and I have not had to fill the radiator. My first thought was that the thermostat was bad, but wouldn't that be an "all or nothing" issue? Where should I start looking for the problem? It has been going on for about 3 weeks, and I want to get it resolved quickly.
View 10 Replies
I have a 2003 vr6 with about 60,000 miles on it and it overheats. I can drive between 35-40 mph and make short trips no problem but when going any faster or accelerate faster than an old lady in a buick, the temp gauge slowly rises(or fast if i accelerate fast.) Until the "stop, check coolant" warning comes on(which i don't let get to that point.) it blows heat all the time, all the hoses get hot, I am no professional by any means but i have dealt with many different overheating issues with other vehicles but I am kind of stumped at what to try first so i don't end up replacing something that doesn't need to be because i do not have the extra $ to do so. The problem started when someone put dirt in my coolant, I flushed out the system twice, the second was just to see if anything else had loosened up that I may have missed the first time..
View 2 Replies
2000 Ford F150 1/2 ton 2x 5.4L... Last year, I started having a problem where when the temp dropped below 50 degrees outside, my F150 would idle really rough and sometimes stall out. The CEL came on and reported some codes that I don't remember but pointed to bad air/fuel mix. I consulted a friend and he suggested changing out the IAC. I did that just towards the end of the cold weather spell we were having and the engine ran great so I assumed it was fixed.
Well, the temps have been below 50 for 8 days now and ever since the temps dropped the problem has come back. I took it to AutoZone to have the codes read and they gave me the following:
P1151 - Lack of O2 switches -bank 2 sensor 1 : ECM could not adjust fuel trim because of a lean or rich condition
AND
P0171 - Fuel trim bank one condition : The powertrain control module uses the oxygen sensor to calculate the Air/Fuel ratio of the engine. The computer recognized a rich or lean condition on one engine bank only.
Both printouts that they gave me mentioned the following:
Poor fuel pressure
Bad or Malfunctioning MAF sensor - Dirty/defective
Oxygen sensor defective
Fuel injector problem - Leaking or fuel pressure high/low
Vacuum leak on engine
I again called my mechanic friend and he suggested cleaning the MAF and if that didn't work replacing the MAF. I cleaned it and the problem was better but still not fixed.
View 3 Replies
I have a 05 6.0l. Egr deleted. And my truck has a rough idle and power loss. Ive tested the ipr and the icp and they are reading at specs. I've also replaced the Hpop about 1500 miles ago. It has a real rough idle until it's at running temp. And it has power loss, I'll be driving down road and theres no where near has much power has there should be. And the idle will jump between 1500 rpm and 2000rpm.
View 9 Replies
'03 6.0 Powerstroke. Rough idle AFTER it warms up. Runs fine cold. It seems to studder and miss at mid range acceleration. Egr deleted and new oil cooler installed. New lift pump. Replaced ICP sensor. Have 48.5 volts at the FICM. Replaced the fuel pressure spring to the blue one. All new filters. Does not smoke. Does not throw codes. I need to fix this truck one last time. It has a date with the bottem of a very deep lake! It has been nothing but a pos since it hit the ripe old age of 25k miles!
View 14 Replies
My new-to-me 2001 Ranger 2.3L runs great except for this one problem: At under 2000 rpm, if I give the gas more than the gentlest tickle it misses and bucks until I back off. It also misses at idle. There is no CEL but I did pull a P0442 code which points to the evap purge valve. At above 2K rpm, it runs like a champ and I can floor it, except when under load such as climbing a hill.
Could this be the problem, or should I look elsewhere also? I'm not one to just throw random parts at a problem. The previous owner thought it was old gas or an injector, but I would expect it to run poorly all the time. The service writer at the Ford dealer thought it sounded like an electrical issue, but coil, plug wires and plugs are new.
View 8 Replies
I have a 2000 3.0l ranger. I have been battling an ignition problem. every time the engine is cold it runs terrible like only 3 or 4 cylinders running terrible. if u put a timing light on the wires the pulse comes and goes on random wires. and when it quits that it has a random sputter at idle and misses around 4k when u get into the throttle ...
I have replaced plugs twice and the coil with motorcraft parts and the wires are new autolites. I have also replaced the thermostat and fan clutch it was getting hot in the middle of this other issue ...
Every time I replace something it runs great for a few days then back to running terrible again. am I missing something else do I need to look at a computer or map or tps sensors, or something like that ...
View 5 Replies
I have a 1999 passat 1.8t and its having problems accelerating. When you hit the gas pedal the idle rises and drops constantly. What this is?
View 3 Replies
I have 2007 6.0, rough idle starts, rough and no power till engine reaches running temperature, runs great after that. If the engine is off for half hour, and restarted, runs rough again till engine temp is back again.
View 3 Replies
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
View 7 Replies
I have a 2006 f250 with a 6.0 with sct livewire, arp studs&gaskets, oil cooler, blue spring mod, sinister egr cooler and it had been giving me some real troubles lately. Started off as a code for injector #8 so I replaced that and while I was in there I rebuilt the oil rail with new nipple cups and orings, replaced standpipe and dummy plug in that bay(also updated the arc fitting less than a year ago), new exhaust back pressure sensor tube because it was right plugged with carbon, and a new egr valve because that was right packed with carbon as well, all backed together and torqued to spec from the Haynes manual and the truck still sounds like its missing at an idle with some light smoke(just smells like unburnt fuel). From there I went to test the ficm which is also only a couple years old and it seems to stay at a constant 48v so at this point...
View 11 Replies
I have a 2007 F250 4X4 6.0 diesel. When first started it idles extremely rough to a point it sounds like a old gas engine missing. But after it warms up for about 15 minutes it runs and idles like a new truck. I'm thinking it's the injectors if so is this something I can change/clean .... It's 98* on a cool day , when "cold" I mean just started for many hours.
View 13 Replies
I recently purchased a 1999 6.8L. Runs great when cold but after warming up the idle gets rough. Truck has new plugs and coil packs and fuel filter. Checked the fuel pressure and the idle is right at 30 psi. I read that the good pressure range is 30 to 45 psi. Is 30 psi acceptable or should I replace fuel pump or regulator? Any next step to solving my idle woes.
View 3 Replies
I am new to the v10 I only ever owned 7.3 this is my father truck it's a 99 with 200k on it. The problem is it will idle fine when cold but when it is warned up very ruff idle no codes and when I go back at the end of this week I will check the O2 sensor with AE but I really don't know much about it.
View 2 Replies
My 2003 7.3 f250 has trouble starting whenever the temperature is less than 65 degrees. If it is less than 50 degrees I have to plug it in for it to start. Once it starts it runs rough. I let it warm up and it still runs rough. Once I start down the road I'll get on it a bit and it takes off like something lets loose. It then runs geat for the rest of the day but does seem to still crank a little more than it should when I restart it through out the day.
The pickup has 152000k
List of repairs I have done to the truck:
-new gpr
-new glow plugs
-new uvch both sides
-new valve cover gaskets
-new blue cps
-new fuel filter
-new batteries everstart maxx 65n
The truck has an afe air intake, straight exhaust, and a super chips tuner set on mileage saving. It blows white smoke when first started but clears up pretty quick.
View 13 Replies
I have a 99 f250 5.4l 2v with 165000. just two weeks ago i went to start up the truck on a job site to take lunch and it was running really rough. I talked with a mechanic at my shop and he said that it sounded like the aic or that i needed plugs. I went and bought aic and plugs and installed them all in one day. I unhooked the battery before i did any work and have changed the coil packs about 3-4 months ago when it was jerking at highway speeds. I am at a loss.
Read so much on the site about could be this or that and cant afford to through money at it like the govt does. I replaced the ait(air intake temp sensor) and the ect(engine coolant sensor) after i got a code from oreillys that said p0113 which is high input on it. I have read it can be so many things and it seems to be running rich because i am getting about half of mileage i was getting before problem started. i need a fix soon as i must drive the truck to work everyday which is a 52 mile trip total.
View 14 Replies
Truck has been doing this and now getting worse. 06 f250 6.0 147,000 miles. Runs like crap when you first start and truck has trouble shifting when I first take off in the mornings until it warms up then it idles fine and runs like a champ no problem shifting. Not in a cold climate 40F at the least. Not trying to take it to the dealer and get raped. Been doing research some people say get the inductive heat flash, some say needs new injectors, some say could have a bad gasket on the injector idk. I'm trying trying to get it resolved....
View 4 Replies
