Ford - Explorersporttrac :: Power Steering High Pressure Hose Failure Leak
Apr 25, 2013
Just had dealer repair shop complete power steering fluid flush in Jan 2013. Vehicle now has lost all power steering fluid (April 2013) and dealer repair shop has told me it is due to high pressure hose failure - need to replace & then verify pump condition (dealer repair shop not sure if pump bad until hose replaced to test) for repair bill.. I was told this was not related to repair shop power steering flush because this hose not removed for flush or part of that procedure (at which time a transmission flush & spark plugs replaced (minor tune-up) . Just wondering if any pro mechanic can respond with advice about the relative close time frame these two events & if there may be a probable related reason?
View 4 Replies
Advertisement
My high pressure power steering hose just blew at the "B" nut at the pump. Meaning, the fitting is still in the pump but the line is out. Do I need to replace the whole line or is there a retainer I can swap out?
View 14 Replies
I have a 2004 with the 4.6l. The high pressure hose is leaking from rust. From other posts I have read, it looks like I should rent a puller and remove the pulley first, and then I'll have access to where the hose connects to the pump.
Question: The leak occurred while driving home from vacation today. Went we stopped for gas, we noticed a shutter in the steering. I added about a 1/2 quart to the reservoir - there was still some fluid but foamy. I made it home, and I when I checked again the reservoir was empty.
Should I go ahead and replace the pump while I am at it? I wondering it if could have gotten damaged from low fluid. The truck has 190k so it's not like the pump owes me anything. Will it make any of the repair easier to toss out the pump too?
View 9 Replies
How to remove the "high pressure" power steering hose. I have drained the fluid, disconnected from the pump, and also from the rack. Removed the center clamp, and got it all "loose". However, I cannot seem to figure out how to "fish" the hose out. There is a long piece of metal tubing that connects into the rack, and it seems to be resting above some cross member that is not removable. Went to the library, and searched the AllData Online manuals. On the "How to replace the High Pressure Hose" page, it only showed a diagram of the power steering system, with no written description on how to remove the hose. I am not on a lift, but jacked up and supported and on my back under the car with the right wheel removed. I am stumped, and the new hose is due to arrive soon.
View 2 Replies
I have a really small leak coming from the lower end of my power steering hose, it's super small, I was wondering if I could fix this by wiping it down really well and dry, and then layering it with plasti-dip. I think the leak is small/slow enough for me to get in a few good layers. Would this be an okay fix, or would the plasti-dip separate fast?
View 2 Replies
I have an 07 Camry with a hard to turn steering wheel. I had to replace the high pressure hose from the rack due to a leak. After that I basically bled the system as one would do under normal circumstances. With the cars front wheels off the ground I turned the wheel hard left and right. The wheel did give a bit but not to the point of perfection. After many turns I put the vehicle on the ground and repeated the process. The fluid no longer leaked but the stiffness was still there.
The hose was replaced at 110,000 miles. It's currently at 112,000 miles
View 14 Replies
I think I've tracked my power steering leak to some type of sensor on the pressure line, close to where it connects to the steering box:
I assume this is a pressure sensor? I got no CEL or anything like that when the fluid had leaked down to the level that the pump started whining pretty badly though. As far as I can tell by looking at pictures, the parts store replacement pressure lines do not have this sensor, or any provision to connect a sensor to it: Advance Auto Parts: Power Steering Pressure Hose by Powercraft - Part 71878
I may just put a replacement line on there and leave the sensor plug hanging and see what happens...
View 11 Replies
My uncles 1999 v10 started to leak from the high-pressure hose on the gearbox. Replaced the hose which lasted for a short time but is now leaking at the same spot. The hose swivels, is this normal, seems like a dumb design for a pressure hose. Also is there a certain trick to doing this hose? He also insists on using PS fluid instead of the ATF it calls for. Could this cause a problem with the seal?
Edit: Also the truck has been lifted on 35s since 16k miles and its now roughly at 170k. He tows with it as it is his work truck. But the truck is well taken care of.
View 3 Replies
I have an 03 Accent. The all metal high pressure power steering line had a leak. So I bought a new one for around 70 dollars from Hyundai. This part has a curved shape and fits around the radiator. The old one was difficult to get off, but the new one is proving impossible to get on. I cant get it into place.
View 2 Replies
2001 F150 Supercrew 5.4L ... Dealership unable to locate replacement pressure hose for power steering . I've returned 3 wrong parts. The hose in pic goes all the way up to the reservoir.
View 13 Replies
Just replaced power steering pressure hose while engine out as PM. New hose wasn't correct shape so I bent the tubing to fit. I later realized that I bought a hose for power steering without variable assist and the hose for variable assist looks correct.
Is there any harm in leaving the "w/o variable assist" hose in now?
View 1 Replies
The Power Steering Reservoir has a small leak that makes the area under it looks oily and messy, so i followed a member's DIY PS flush, I used Walmart Supertech ATF Dexll/lll fluid but now I am thinking about using Mobil1 Synthetic ATF once I get the reservoir out.
The new red color shoes the leak is coming from the edge of the connection between the top and bottom plastic parts of the reservoir.
so my questions are:
1- How do i remove/pry or pop the reservoir out of its bracket?
2- Can i use JB Weld epoxy to glue/reinforce them parts together or just pick a used one from junkyard?
and last question: What size ID/OD is the PS fluid low pressure hose?
View 7 Replies
I have a 1989 Honda Accord DX with less than 120k miles. I have two problems.
1) the low pressure hose for the power steering has worn out and is leaking by the fittings (badly) and I can't find the parts to fix it. The high pressure hose was also leaking but we found and replaced that part, and
2) I accidentally topped off the power steering reservoir with brake fluid (this was after I already knew the leaks existed).
View 4 Replies
So, I have a 1995 Jeep Grand Cherokee (Orvis edition) with about 270,000 miles. It still runs great and has been really useful in the snow this winter. A couple days ago the power steering pressure hose blew. My mechanic wants to replace it, but I can get a replacement hose locally. Is there any reason I shouldn't just do this myself. Do I need to worry about the fluid sprayed around the engine? The serpentine belt is only a few months old and squeaked only a little on the three mile drive to get it home.
View 8 Replies
I've got a 2006 Sonata LX, that has been leaking PS fluid for a while, but has gotten quite a bit worse lately. I finally put it up on ramps, and crawled underneath, and from what I can see, I think it's leaking from the pressure hose someplace.
The hose is covered with some type of a silver wrap. I wiped everything down as much as I could with a rag, waited for an hour, then crawled back underneath. There was some new fluid on the hose wrapping right above where it goes into the steering gear box (the driver-side leg of the hose).
Does this sound like it could be the hose? Would it be ok to remove the protective wrap to make sure? it's only wire-tied on to secure it, so I don't see why not.
View 1 Replies
I have a 2006 RX 330 with 116,000 miles. I noticed that i had a leak and the power steering oil level was low. I went under the car and looks like the power steering hose is leaking. The dealer wants $352 for hose and $325 for labor. I called auto parts stores and they say its a dealer item only. Someone told me I could have a hose company rebuild it for a lot less.
View 5 Replies
I just recently had a new pressure hose (had a leak) replaced on the power steering pump but there is a slight squeaking noise when I turn the wheel. the mechanic says it'll go away after a week or so because of the new fluid that was put in? Is this correct?
View 4 Replies
Truck has a high oil pressure leak, only leak i have found is in the high pressure rail, I cannot get to it till sat, or sunday. So I have to let the oil cool before I can start. Any way testing to find the right temp for Oil to thicken enough to Build? I've been here for hours and its went from 180's to about 100 now...
View 3 Replies
I have a High pressure oil leak somewhere, and where it can be. I tore the oil rails out and replaced the nipple cup seals last night. I got it all back together and air tested it and sure enough a leak is present. I have no problem paying for your time (I always provide good beer). I can rebuild gas motors all day long, but these diesels has me thrown for a loop. The frustration I am experiencing is crazy at this point. All the injectors are new, and the dummy plugs and standpipes were replaced as well.
View 11 Replies
I just replaced my 3rd HP power steering line last night( 3rd in 300K, always blows the same point....fitting comes apart where it attaches to the pump.
I'll start, mine have gone about 100K plus or minus 10K, almost thinking about making it a 100K maintenance item.
View 14 Replies
My 03' 6.0l hpop only makes about 1700 psi at wot, at hot idle the ipr is 25.1 and the icp is about 580. It runs pretty good but it seems the crank time to start is getting a little longer sometimes, other times it fires right up. It makes no difference if its hot or cold. Do pumps get weak or do you think I have a leak?....
View 1 Replies
