Ford - Explorer :: Stop If Don't Step On Gas After Starting - Rough Idle
Nov 25, 2013
1994 Ford Explorer; When I start it, if I don't step on the gas it will stop. If I give it some gas when I start it, the engine will race and then decelerates about 2000 rpms and keeps doing this, it does get better as the engine warms up. But the idle is really rough. It has new wires, plugs, vacume lines, oil change, air filter and battery. If I put the gas pedal to the rug, it will go from 4000rpm back down to 2000rpm and continue doing this as long as I keep the pedal to the metal. I had it put on an analyzer and it didn't read anything.
View 6 Replies
Advertisement
1987 Ranger and the computer will not communicate. I'm trying to check for codes because of a rough idle and stumble when starting out from a stop. Check engine works but won't flash when using a jumper across the data link. Used a OTC scanner but it only times out and comes up "no data". Where to go from here?
View 7 Replies
I have a 96 Mazda Protege DX. 1.5L engine, now with 161,000 miles. 5 speed manual transmission. I had it for 7 years. Originally bought it for $1900 with 121,000 miles.
This has been a problem for about 5 years. When I am at a red light or idling and I step on the brake, my idle gets rough and my engine feels like it is about to turn off. The idle does not bounce up and down. It just goes down to 400-500rpm from the normal 800-950rpm range.
Again, this only happens when I step on the brake while the car is not moving. It does not seem to happen when I coast in neutral and hit the brake to slow down. I raised the idle a bit, but it still does it. I could not find any vacuum leak around the brake booster and I know the brake booster works because I pumped my brakes while the car was off, and when I turn the car on, the brakes soften up.
Also, my brakes feel weak. I usually hit the brakes nearly to the floor board to stop the car. New pads, rotors are good. Brake fluid is at right level. Mechanics say nothing is wrong with my brakes.
Secondly, my belts screech at every start up. Lasts anywhere from 3-20 seconds. This has been happening for the entire 7 years I have owned the car. Mechanics replaced the serpentine belts twice in that time. Replaced a pulley and A/C compressor. I tried using WD40 but it doesn't effect it. Mechanics tell me that the belt tension is correct and they do not know why it still screeches.
View 6 Replies
Grinding feeling, and noise from rear of 02 explorer xlt. only noticed when starting out from a full stop and turning. It feels like something is grabbing like the rear brakes. I purchased this suv of a local dealer lot, because it was so clean and on a short test run seamed fine.
The day after I picked it up I took it for a shakedown cruise to see if I noticed any problems. After going up a few forward grades I noticed a disturbing rattling noise coming from mid under carriage, and got very worried. I immediately took it to a local well revered mechanic. They eventually had it for 4 days in order to diagnose it. After the dealer had done the inspection on the car and passed it, that all rotors and pads needed to be replaced, left front wheel was locked up, inspection sticker month was never punched, both front tires were bad and either the flex plate or tork converter or both needed to be replaced. I took it back to the dealer with the report and he agreed to fix it with me paying for parts. He did and the rattle was gone !
Yet now I have noticed the problem mentioned at the beginning of this piece, plus the rear wiper does not work. I think I got taken for a ride, which may become a longer ride than I thought. All I want is a reliable car. what could that rear noise be ???
View 5 Replies
When I start the truck it hard to start and the idle is rough but when it warms up it seems to get better but still miss fires now and then so i was thinking could it be a bad O2 there is now "CEL" because the battery was dead (installed a new one) and the truck has not been on the road yet (want to get everything fixed first) and update on the door alarm will be working on that tomorrow almost forgot 2002 explorer 4.0L "E" for the vin 4 wheel drive 124k on it.
View 5 Replies
The problem starts after about 5-10 mins of start up and normal driving. First signs usually come leaving a stop light or stop sign. Hesitation, jerkiness, rough acceleration. It's usually slight, just enough to feel it. Soon it really shows up while keeping the truck at a steady speed, say 40 for example.
I finally heard what I would describe as a puffing air sound and figured vacuum leak.. finally! Nope.. it's coming from the rear underneath of the vehicle. I can't hear it in the engine, or the tail pipe.
2002 Ford Explorer xls 4.0 125k miles, I've replaced the air filter, egr valve, pcv valve, cleaned the maf and covered about every hose I can reach with carb cleaner checking for a vacuum leak. I've yet to try some of the other things due to hearing that puffing sound.
View 8 Replies
I have some major problems with my explorer. The idle is rough and accelerating is rough also. If I nearly put it to the floor it almost seems like it studders the power. it will feel great for a second that feels like it's less power for a second then more and less and more and less. When I'm sitting at idle, it will idle fine then after a minute or so it will bog way down and shake the whole vehicle. when that happens I give it some gas and it comes back to normal idle then it does it again after sitting for another minute. I've replaced spark plugs, wires, alternator, oil change and some tires. I've been told by many mechanics it could be the IAC Valve or the fuel pump or the fuel filter or a vacuum leak.
View 8 Replies
My explorer has been running a little rough, particularly at idle. When I take off from a rough idle, it'll run rough until I hit 25-30mph. I ran by O'Reilly's hoping to pick up a pack of spark plugs and be done with it, ended up leaving with a new MAF sensor. It ran better for about 10 miles (I'm a delivery driver, so I did a lot of stop and go immediately), before it ran even worse than it did before, but at least my CEL finally came on. Took it back to O'Reilly's and they read a MAF sensor code and a catalytic system code (didn't ask for the codes, and now realize that was a mistake).
So today I took it to a muffler shop to have the catalytic system diagnosed. They looked at it for 10 minutes and told me they didn't think it was the converter. They said it seemed more like the EGR valve or solenoid, or the IAC. He scanned the codes again and got multiple "running lean" codes (0171, 0174, etc). The guy said I didn't have a vacuum leak, so I think I can rule that out. Unfortunately, the truck idled fine the whole time so he didn't feel comfortable giving me a definitive answer. He told to to leave the EGR valve hose unplugged for a few days and see if anything changes. I'm thinking about running a bottle of fuel cleaner through it or taking off the IAC and/or EGR and cleaning them myself.
View 6 Replies
99 explorer 4.0 automatic, lately been running weird. Starts up but will stall out unless you let it warm up. And idle drops below 500 rpm. And is really rough feeling. To like 2 or 300 rpm, then will stall but will start right back up. When I changed spark plugs and wires problem stopped for about 2 weeks and now is back. And has no engine code.
View 7 Replies
What can cause my 99 explorer xlt to have a rough idle on initial start ups?(Its worse in the winter time) And sometime after driving places when i put it in park the truck will cut off. It has the 6 cylinder SOHC if that's useful.
View 1 Replies
Bought a used 2003 Explorer 4X4 that runs like crap.... All I know is it has new upper and lower radiator hoses, new battery, new brakes, 2 new tires and new belts... suspension seems great and body is nice too. It obviously needed a new radiator and complete exhaust, so I did those. Now it is running better ( I can actually get the RPMs over 1500) but still running rough and will stall if I let off the gas. It will surge and dip in RPMs. Very suspicious of vacuum leak.
Unplugged the MAFS and it roared upon start but within a minute started the sputtering etc. Currently pulled the IAC and check continuity between pins and it was 10 ohms so that passed but there is no continuity between either pin and the case. So this seems to indicate I need to replace the IAC which I will do tomorrow. I would love to find a diagram that displays the vacuum system so I can make a thorough check of it. Also seems to have an oil leak on drivers side valve cover gasket.
View 14 Replies
2009 Ford Explorer - 6cyl -4L - 36K miles. This morning driving it, I came to a stop sign and as I was braking, the idle starting going up (and up and up) to the point where I had to shut off the engine. When I restarted it, everything was fine and of course, I can't reproduce this. I have the shop manual and couldn't find an IAC valve on this vehicle which I'm assuming it doesn't have. I'm sure I didn't accidentally hit the gas (as opposed to the brake which I know I was pressing down on when it was happening). Years ago I had a different Ford which had the exact same symptom and replacing the IAC solve the problem.
View 3 Replies
I have a weird intermittent problem. Sometimes when I start my explorer it will idle down and die immediately, I restart and it will idle about 400-600 really rough, sounds like it is missing. When I drive it it is jerky and the acceleration is sluggish but after I get it up to about 20 mph it clears out and then drives and idles fine until I shut it down. Plus these things only happen about every third time (on average) that I drive it. Lastly it's not giving me any codes. What this could be?
View 2 Replies
ok, 3 times now I've been extremely close to being hit head on by oncoming traffic due to a seemingly uncurable stalling problem. It idles rough sometimes, and other times it seems fine. BUT when sitting at a light, waiting to turn left after the oncoming traffic has a quick opening, I start to go, I get halfway across the intersection and then without warning, it dies completely. Now its too late to stop and back up- and the cars are flying head on towards you locking up they're brakes. One time I would have been killed by the 18 wheeler that was coming if I hadn't gotten it started and moving again just in time.
I replaced the IAC, the plugs, filters and wires, and the EGR valve. I checked everywhere for intake leaks and found nothing. Changed the O2 sensors since they had plenty of mileage on em. It idles like crap still, even after 30+ tanks of every kind of injector cleaner they make. We used the snap on scanner tool to monitor things and it never acted up then. The TPS seems to move smoothly, and fuel pressure was checked and found to be around 25-30 psi. Don't know if that's normal. The intake air temp was reading a constant 120 degrees F. I also checked the fuel cap to make sure it was closing completely. The dealer checked the TB for excessive clearance and said it was ok.
It seems to only stall like that after driving on the highway and then stopping at the first light after that.
View 12 Replies
I have a 2004 Explorer with the 4.0L SOHC V6.
I was having some rough idle and a P0401 code for Insufficient EGR Flow. In the process of investigating the EGR valve, I had to remove the throttle position sensor to remove the EGR. After re-installing everything, I had a worse rough idle and I again removed the EGR valve; however this time instead of removing the throttle position sensor, I removed the entire throttle body assembly.
After re-installing everything again, I now have very rough idle and no pedal response. I have the following two codes:
P2104- Throttle Actuator Control System Forced Closed
P2112- Throttle Actuator Control System Stuck Closed
I did not unplug any harness, and all connections are secure. I did not remove the battery cables while working on it, but I did remove the negative cable for about 45 minutes after getting the P2104/P2112 codes hoping a reset my fix things.
View 3 Replies
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesn't stall very often at all. Accelerating I notice way less power and the engine studders. That's when the engine light comes on flashing. Then remains on solid afterward. I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as the O2 censor.
I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gaping. Thought I had fixed the problem. The vehicle ran perfectly. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it. Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
View 1 Replies
My truck is a 1995 Explorer 4.0 150,000 miles, 5 speed.
Problem - Rough idle : when cold it's worse and will stall and choke a little. When warmed up it just has a rough idle but will not stall and stays at a pretty constant RPM. It's very tolerable when warmed up but still not right. It drives fine once off idle. No black smoke that I can see. Power may be just a little off but I would not bet on it. MPG seems about normal but haven't been on a long enough trip since problem started to tell for sure. Also longer than normal cranking on occasion.
Diagnostics so far : Fuel pressure is at 32 PSI, vacuum off regulator it's at 40 PSI. Not sure about key on only as I don't trust the autozone loaner gauges. You have to fiddle with it each time before it will read. Leak down after 30 minutes was about 4 PSI
No Check engine light ever. KOEO test shows no hard or on demand codes, I get the 111 pass. From CM I get 336 and 45.
336 is EGR related and my looks pretty rusty. I put a vacuum pump on it while running and the EGR held vacuum but had no effect at all on idle, I was expecting it to get worse as I opened the EGR so it may be stuck.
Searched high and low for vacuum leaks by ear, visual and with starting fluid all turned up nothing.
Actions so far : Replaced plugs, wires, IAC, and fuel filter. Cleaned MAF sensor and throttle body plus ran lucas fuel injector cleaner through it.
Next steps : I've got the EGR but it's so rusty I am sure I'll break the tube it bolts to plus I don't know it that alone will cause the rough idle. Will the DPFE sensor and/or EVR create a rough idle yet not turn on the CEL?
Thought about changing the fuel pump and/or regulator but the numbers are not terrible. Agree?
Thought about changing the intake gaskets but don't see any leaks.
View 8 Replies
Explorer with 4.0 has a rough idle, just put new plugs & wires, air filter looks good. i did get a new fuel filter as well but haven't gotten to that yet. It has 102k. I have read some info about motor mounts could come lose casing the motor move a little more, not sure about that one. its the wife's haven't driven or looked into it yet, its on the to do list weekend. She also informed that it seems to lose power a little while driving sometimes, thinking possible fuel pump now?
View 4 Replies
I have a 2004 FX4 5.4 with about 113,000 miles on it. Lately, when towing the camper (around 7000 lbs), truck runs great. However, when I come to a stop, it idles horribly and even stalls sometimes. When I rev it up, runs fine again. It only does this after towing when engine is under load for extended periods of time.
The only code it has ever thrown was for bank 2 camshaft over retarded. My thought was that it could be VCT solenoid for bank 2...
View 2 Replies
2003 Ford Explorer 4.6 liter AWD. Having some kind of VERY STUBBORN idle / emission problem. When it started it was an intermittent rough idle, mostly going too low or making a periodic "drumming" sound that could be felt and heard at the air cleaner box. CHeck engine codes were PO 442 evap system leak. I first cleaned and inspected throttle body, mass air flow sensor and idle air control valve. I inspected hoses for leaks, including spraying cleaner to see if I could detect idle changes / leaks. I then replaced Idle Air Control Valve. Did not seem to cure problem . SO took it into Ford Dealership and they smoke tested and said needed Vapor Management Valve and Vent Solenoid. I replaced VMV myself. Idle no longer "rattled" but when driving and braking the idle would drop down very low and sometimes not "kick up" and would die. I then took it back to dealership to have them replace the vent solenoid and reprogram the PCM. Still doing it. They said I might have a defective (new) Idle air control and to replace it- otherwise they dont have a clue.
View 2 Replies
I'm a diesel mechanic and know my way around Powerstrokes, this 4.0 is not what I would usually work on, but I have a friend who has 2006 explorer 4.0L SOHC, someone told him he needed a motor with out explanation why, so I didn't want to see him get ripped off. The problem is it idles very rough, hard to start, and stalls. There's no DTCs , if you hold the accelerator slightly it will stay running, but once you let off it will either idle really bad and misfire or cut off, once pushing the accelerator the rpms raise very smoothly up til 3500 which is what I assume the rev limit is in nuetral.
I've done checks with focom and forscan, I was thinking possibly a bad fuel pump, while monitoring fuel pressure I see a range of 289 - 326 kpa with 26% fuel pump I guess duty cycle would be the correct term(once again I'm a diesel guy, and use to dealing with IPRs and Hpops) not sure if the desired fuel pressure is relevant on these but it always stays at 269kpa. I believe that equals out to 40-48psi while I believe this system is supposed to have somewhere in the range of 60 - 70, but I wouldn't expect to get a rough idle with no load with almost 50 psi of fuel pressure.
So with no DTCs Im baffled, and don't want to start wasting money just throwing parts at it. I've thought everything from fuel pressure sensor, to coil pack(replaced 4 months ago) to crank and cam sensors.
I did end up getting a code p106, but I believe this is because I didnt tighten the intake hose after checking the throttle bottle, I just slid it back on. out of the 4 days of testing first time I seen a code pop up besides unplugging some sensors here and there to make sure the pcm would actually register a dtc.
View 3 Replies
