Ford - Explorer :: 2004 - Misfiring On Cylinder 3 And 6
Aug 17, 2016
Changed the spark plugs now I have misfire in cylinders 3 and 6. Do I change the spark plug wires or the coil pack?
View 5 Replies
Aug 17, 2016
Advertisement
Ford F-150 (2004-2008) :: 2005 - Cylinder #5 Misfiring?
Had a miss in the #5 cylinder on a 2005 F-150 5.4 Triton. Had it hooked up to see which code was given and the tech said that #5 was the culprit. Taking no chances, I purchased a new plug and coil pack. I installed them and it ran great until I got up to around 70mph and then it started dong the same thing it was doing earlier. I took it back to the place that checked the codes and it came back as the #5 cylinder misfiring again. I am not sure how this is possible after replacing the plug and coil pack. Is there some way that the plug that fires just ahead of #5 is fouled out and causing the #5 cylinder to get too much fuel transferred to that cylinder? Or is there a possible short somewhere causing that cylinder to misfire and ruin the coil pack? I am stumped on this for the moment anyway.
View 8 RepliesFord F-150 (2004-2008) :: Misfiring On Cylinder 4 - Changing Spark Plugs
2004 5.4L ... Codes indicate a firing issue on #4 cylinder, figure it's the coil pack. They bought truck used a few years ago and plugs have not been changed since they have owned it. I was going to change plugs while I was under the hood. While checking threads on this engine I picked up on plugs being a major job unless you know the tricks. So what tricks do y'all have up your sleeve to keep from breaking plugs?
View 14 RepliesFord F-150 (2004-2008) :: 2005 - Misfiring On Cylinder 7 / Running Lean Bank One
i have a 2005 f150 4x4 5.4 3 valve. it ides good but when it is in on it splutters, and also feels like dead cylinders in passenger gear. i checked the codes the other day and i had a cylinder 5 misfire. so i cleared it and today checked again and had running lean bank one and cylinder 8 misfire, then checked one more time and had cylinder 7 misfire. I am sure it is a bad coil but how do I know which one?
View 2 RepliesGolf IV / Jetta IV :: 2004 - CEL Came On - Cylinder 2 Misfiring
CEL came on and the report says #2 cylinder misfiring. Changed plugs, wires and coil. Last step was to change the #2 fuel injector. I changed the 2nd injector from the left but I'm still getting the same message. I was wondering if maybe they aren't numbered that way. It's a 2004 Jetta with Car engine: 2.0L L4 SOHC 8V. Did I change the wrong injector?
View 1 RepliesPrius (2004-09) :: Shaking When ICE Is Running - Misfiring On Cylinder 1
My Prius started shaking pretty bad when the ICE is running. This morning I got the codes read and it came as Cylinder #1 misfire. I figured the coil pack is going bad (as is known to happen) so I swapped #1 and #2. The misfiring actually got better for about 30 minutes, but it finally happened and the CEL flashed again.
So I took it to get the code read but he said the only code is still #1 misfire. Perhaps the ignition coil is OK then? I bought a new spark plug, maybe the plug has gone bad. The plugs only have 45k miles on them. I'll swap it out and see what happens. What I should do to diagnose the issue? It seems to be slowly getting better...this afternoon it was much better than this morning but still shaking sporadically.
Prius (2004-09) :: Code P0301 - Cylinder 1 Misfiring During Warm-up
I have a 2009 Prius that I purchased 6 months ago and have been really happy with it until the last couple of months. As the weather is getting colder appears I have a misfiring problem on start-up
I have had this problem now for a little while and have been trying to get it understood before paying $$ at the dealer for "maybe" solutions.
It started as the weather got colder. Intermittently the check engine light would come on. Then after a few days would go off.
I have considered water in the line: fuel injection cleaner/antifreeze
I have considered bad gas in the tank: problem persists several fuel tanks later
I have recently purchased a trouble code reader/diagnostic that plugs into my laptop. Trouble code is p0301. Cylinder 1 misfire.
I have taken it in to the shop.They tried:
>>moving the ignitor coil from cylinder 1 to cylinder 4,
>>and also tried moving the spark plug from cylinder 1 to cylinder 2.
>>performed compression test. Ok
The dealer suggests replacing the injector line for $1400+.( They did this with warm engine. They have not diagnosed cold engine yet. That is new, read more,...) I still have 5K kilometers left on the power-train warranty. If it is power-train I would like it resolved before warranty expires.
Now. Some new info as of yesterday:
Up till now I was not using the diagnostic monitor real time. but that started yesterday,... Last night when I got home from work while the engine was still warm I connected the diagnostic monitor and went for a drive. Every few minutes I would pull over and refresh the cylinder misfiring data. I had hardly any misfires across all the cylinders at all. Maybe 1 or 2, here or there over the span of a 10 minute warm engine ride. Up and down hilly terrain. Nothing that came close to triggering the p0301 trouble code. I parked the car outside and let it rest overnight.
Ford - Ranger :: 2002 - Misfiring In Cylinder 1
Had a misfire in cylinder 1 so I put new plugs and wires. Still misfired. Changed fuel injector. Still misfired. Changed ignition coil and misfire on cylinder 1 is gone now cylinder 2 and 3 are misfiring. I double checked wires and they are properly installed.
View 11 RepliesFord F-150 - 1997-2003 :: Misfiring Cylinder 3 And 8
Trucks throwing codes for cylinder 3 and 8 misfire. I pulled the plugs and both were covered in oil and cylinder 8s electrode was literally gone. so I replaced the plugs and within 5 miles it was missing again. so I replaced all plugs, all wires and coil packs. cylinder 8 plug had fouled out. Its a 4.6l 99. I have a mild exhaust leak where the manifold connects to the downpipe. but not bad enough I feel it should matter. it runs rough until about 3k rpm and then it kinda straightens out.
View 14 RepliesFord Escape / Hybrid :: CEL Came On / Cylinder 4 Was Misfiring
I had a misfire and my CEL came on had it read and it said cylinder 4 was misfiring and that there was a misfire in the first 1,000 RPM's. I replaced the COP and plug and now I'm getting terrible MPG. I tried to reset the PCM by removing the Neg. battery connection and it seemed to work for 4 days now my MPG has gone bad again. It seems to run smooth/good.
View 1 RepliesFord - Ranger :: Stalling Out When Cold - Cylinder 4 Misfiring
I've got a 2000 Ford Ranger, manual 4 cyl. When cold, she's been stalling out. It happens very reliably when I come to a stop and put it in neutral (or put the clutch in). Only when she gets warmed up does it stop. Check engine light has been on (for a long time) saying the TPS sensor is out and the 4 cyl. is misfiring. I replaced the TPS sensor and it had no effect on the problem. A friend recommended changing the oxygen sensor.
View 5 RepliesFord Ranger / B-Series :: 1998 - Which Cylinder Misfiring
I got this 98 Ranger 2.5 that I've done a tune-up on less than 30,000 miles ago. I changed plugs, wires, and both coil packs. Timing belt, thermostat, fuel pump, fuel injectors are all recently changed too within a year or two. Fuel filter and air filter I change every 30,000 miles. The truck runs as great as a 4 Cylinder will run. It's at 344,000 miles but the engine was changed once so it probably has over 100,000 miles on it. There is just a slight miss you can hear through the tailpipe but it's not severe enough to be picked up by the Check Engine Light. In fact, even when the coils were totally gone it never put up the Check Engine Light. I can tell when a coil pack is going out on this because it's done it several times so I usually just change them with the tune-up. It's only a slight miss some people may not even notice it. I was just wondering is there any way to track down where the miss is? I tried looking under the hood in the pitch black and there's no plug arcing.
View 1 RepliesFord Ranger / B-Series :: 2002 - Rough Idle Codes / Cylinder 2 And 3 Misfiring
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 RepliesFord - Explorer :: 2000 - Misfiring And CEL Came Back On
My neice bought a 2000 Explorer Sport back in November. Soon afterwards it developed a misfire and the CEL came on. I put on a new set of wires and a new set of plugs. I noticed when I replaced the plugs that the #3 plug was missing the ceramic near the electrode. I figured it was just a cheap Bosch plug and didn't give it much thought. The vehicle ran great.
Recently the misfire came back and the CEL came back on. When I pulled the plugs #3 had a cracked ceramic around the electrode, #4 was wet with fuel and not firing at all, and #6 was completely missing the ceramic around the electrode.
I replaced the plugs again, replaced the coil pack and cleaned the MAF sensor and it's running great again.
My question is, what would cause the ceramic to disintegrate on the plugs? There didn't seem to be any pinging or detonation. I replaced the coil pack because I thought maybe it was erratic, loading up on fuel and then causing a big bang and then destroying the plug. Are my thoughts way off? I want to make sure this is fixed so that it doesn't tear up anything else.
Ford - Taurus :: Check Engine Light Keep Flashing - Code PO302 Cylinder 2 Misfiring
I have a 1996 ford taurus lx v6 3.0 dohm..my check engine light flashing. then it stop flashing..i did replace spark plug,wires,coil pack..when it start to flash i put it gear the car start to shake and sputter.i really don't know why its doing that the car has about 150000 miles on it..i do get a code p0302 Cylinder #2 Misfire..the new plugs and wires and coil pack is about 2 weeks old..
View 11 RepliesFord - Explorer :: 2007 - Misfiring / Sputtering And No Power
2007 Explorer Sport Trac was misfiring when first started and then would settle down. Now it is misfiring and when I try to drive it, it does quiet a bit of sputtering and has no power. Took it to mechanic he said it would be hard to tell if it was fuel injectors or what.
View 5 RepliesFord - Explorer :: 2000 XLT 4.0 SOHC Does Not Start / Misfiring
I just bought a 2000 ford explorer which didn't start... I put a new fuel filter, spark plugs and air filter in it...still not starting ...gonna do a a compression test tomm. and see if it the timing chains or tensioners... Sounds like its misfiring actually, it doesn't start with starting fluid sprayed in it....where is the ignition pickup located on these things? I still need to put a new ignition coil and wires on it. plugs were in horrendous shape and i thought that was the problem.
View 13 RepliesFord - Explorer :: 1997 - Misfiring Constantly Most Of The Time
My 1997 Explorer 4.0 is giving me a run for my money. About a month ago, it started misfiring and threw a P0300, 301 and 306. It didn't misfire constantly though only most of the time; sometimes it would run perfect which leads me to believe the issue is electrical. I've had trouble with the coil before so I changed it and no difference. The next time I scanned it, there was only the 306 code. Next I made sure that cylinder six was misfiring and the rest were firing by pulling the wire off the coil.
All checked out but one and six. I've already checked the wires, they're both good. I swapped the plug on cylinders 5 and 6 in the hopes that the problem would follow the plug; nope. Fuses are all good. So I know the coil, wires and plugs are good. That leaves me with air and fuel. I can't imagine anything is wrong with the air intake seeing that it still runs. That leaves me with fuel. It has 200k on it and I've never done injectors. Maybe its injectors but why would they only be faulty part of the time?
Golf IV R32 :: Misfiring On Cylinder 2 And 5
Happened a few times on me lately. While pulling towards the top of 5th, I'll start to see the check engine light briefly blink as if the car wasn't sure, then at the top of 5th, she'll start misfiring on cyl 2 and 5. It's only during the long haul pulls that this occurs. My plugs and coils were all changed about 1k miles ago.
View 17 RepliesFord F-150 - 1997-2003 :: Truck Is Misfiring / Blown Head Gasket Cylinder 6 On Driver Side
Ok I got this truck from my mother-in-law for free with a blown head gasket cylinder 6 driver side. I did the replacement had the heads machined put it all back together by the book. Now I can't get it to fire on all 6 cylinders only 5 I think. Thought maybe bad gas (it sat since late November) put 5 gallons (over double the gas) fresh gas and half a bottle of b-12 chem tool. Dubble checked all plugs wires connections (coils plugs wires all new). I drove for about 10 miles oil pressure and temperature stayed perfect but no change in running truck shakes a lot and no real power. Don't sputter or backfire no engine codes other than imcr bank 2 open. Engine is 4.2l v-6 170k miles.
View 2 RepliesLS / MKZ :: 2001 V8 Shuddering And Misfiring On Cylinder 2
Going up a hill this LS started shuddering and misfiring and set the po302 code. A small push on the accelerator sometimes seems to temporarily remedy the issue. This started about a week ago. fuel mileage : 26 mpg highway
Here's the readings I got at idle:
Fuel pressure is KOEO - 0 (That's what it read.); KOER - 30.
MAF - about 70
LT FUEL TRIM 1 - 5.5
ST FUEL TRIM 1 - STAYS NEGATIVE
LT FUEL TRIM 2 - STAYS NEGATIVE
ST FUEL TRIM 2 - STAYS NEGATIVE
ST FUEL TRIM 11 - STAYS NEGATIVE
ST FUEL TRIM 21 - STAYS NEGATIVE
O2 1 - NORMAL FLUCTUATES PROPERLY
O2 S12 - STAYS ABOVE .500
O2 S21 - NORMAL FLUCTUATES PROPERLY
O2 S22 - STAYS ABOVE .500
Not familiar with this vehicle...