Ford - Explorer :: 1999 Will Not Idle Unless Put It Into Gear
Jan 14, 2012
1999 Explorer starts then will not idle unless it is put into gear. It only happens once in a while...
View 2 Replies
Jan 14, 2012
Advertisement
Ford - Explorer :: 1997 - Stay Idle Kick Into Gear And Jump Start - O/D Light Flashing?
I have a 97 Ford Explorer. I bought it in 07 and it was nice until like 2 years ago when it started to give me doubts. It never died on me,yet, but everyday when I first start it for the day, if I put it in gear right away, it will stay idle for a while and then kick into gear and just jump. I would drive but it keeps kicking off and on until it is warmed up, I guess because it goes away. Also the OD light would come on also.
View 2 RepliesFord - Explorer :: 1999 - Stalls Low / Rough Idle
99 explorer 4.0 automatic, lately been running weird. Starts up but will stall out unless you let it warm up. And idle drops below 500 rpm. And is really rough feeling. To like 2 or 300 rpm, then will stall but will start right back up. When I changed spark plugs and wires problem stopped for about 2 weeks and now is back. And has no engine code.
View 7 RepliesFord - Explorer :: 1999 - Rough Idle At Start Up?
What can cause my 99 explorer xlt to have a rough idle on initial start ups?(Its worse in the winter time) And sometime after driving places when i put it in park the truck will cut off. It has the 6 cylinder SOHC if that's useful.
View 1 RepliesFord - Explorer :: 1999 V8 - When Changing Into 3rd Gear RPMs Will Keep Rising
its a 99 explorer xlt AWD 5.0l v8. It has the AODE/w tranny. When I take off with it (normal accelerating) it shifts fine from 1st to 2nd. But when it is suppose to change into 3rd gear the rpms will keep rising as i give it gas. When I let off the gas it goes into neutral. I plan on changing the fluid and filter in it. But need to know if there is anything to check in the valve body before putting new fluid back in? This problem has come at a bad time for me.
View 4 RepliesFord - Explorer :: 1999 V6 Noisy And Idle Will Decrease After It Warms Up
Since we bought this car, it has had an issue where, after it warms up, it begins making a noise which I've seen described as "moosing" on the internet. In addition to the sound, the idle will decrease and will sometimes kill the engine.
I've seen this attributed to the IAC, and so I replaced it (twice). I have tested the IAC connections as well, and all is good. I have even run the car without the IAC plugged in, to try to reset the computer, to no avail. I feel like I have eliminated the IAC from being the problem (but maybe not.)
I have replaced the PCV valve.
I have replaced the water temp sensor and the thermostat (someone suggested this might affect the computer and rpms...)
I have cleaned the MAF and tested it per the Chilton's manual. (tested fine)
I suspect that because of the idle and the engine seeming to be choking out when it dies, that there is a vacuum issue somewhere. I just don't know where to start with this.
Ford - Explorer :: 1999 - Misfiring - Shaking - Rough Idle - CEL Flashing?
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesn't stall very often at all. Accelerating I notice way less power and the engine studders. That's when the engine light comes on flashing. Then remains on solid afterward. I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as the O2 censor.
I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gaping. Thought I had fixed the problem. The vehicle ran perfectly. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it. Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
Ford - Explorer :: 1999 - Misfiring / Shaking / Rough Idle - Engine Light Flashing
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesnt stall very often at all. Accelerating I notice way less power and the engine studders. Thats when the engine light comes on flashing. Then remains on solid afterwards.
I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as O2 censor. I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gapping. Thought I had fixed the problem. Vehicle ran perfect. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it.
Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
Ford Ranger / B-Series :: 1999 - Shaking When At Idle In Gear
I just got a 99 2.5 rwd auto and it shakes when it's at idle in gear. I'm pretty sure its because the AC pulley is engaging drawing power. I was thinking about turning the idle screw up a blonde-one because when I hold the brake and give it slight gas it goes away.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - High Idle While In Gear / Stay At 800 RPM
So finally got my truck running due to a fuel issue. Anyways been driving it for a week or two now, and I have a strange problem idk if it has been covered here or not.
Driving around tow etc if you come to a light or whatever and stop the rpms stay at 800rpm. Now if you shift it out of gear and back into drive the rpms settle back down around 650. Where is should be.
My guess is the torque converter is not disengaged all the way when it stuck at high rpm (800-900) for this situation. No cel, slippage, or crazy noises
2002 7.3 power stroke all stock right now @160k black crewcab
Previous owner had a tunner on it but not anymore. Could it have smoke the trans???
Ford Super Duty (1999-2016) :: Low Idle In Gear / Occasional Stalling When Going Into Neutral
My '05 (134k, rwd, V10) has had an occasional issue with stalling when going into neutral. The normal idle speed in park or neutral is 700. In drive or reverse it dips down to 350 or so and then evens out at 500. The stalling is not all the time, perhaps 2 out of 10 shifts. It is slightly worse with the A/C running. Every time it stalls, it records a P0506 error which I then clear out with my ScanGauge II.
I have done some research and have replaced the air filter (super dirty), fuel filter (not sure on how old) and cleaned the MAF tonight. For the MAF, I pulled it from the air tube and gave it a bunch of squirts of MAF cleaner. I did this 3 times letting it dry in between cleanings. I have run a bottle of SeaFoam through it, as well. The idle seems to be very smooth and it pulls my 7k travel trailer without issue. That did get a little better with the new air filter and fuel filter.
I went for a ride tonight and the problem persists. I'm taking it in to have the A/C recharged next week and will have the shop diagnose it. I came across this post which details my issue exactly. The steps are to reprogram the PCM and TCM, and possibly replace the throttle body. Is the reprogram something an independent shop can/should do?
P0506 idle lower than expected on 05 ford f350 v10
Ford Super Duty (1999-2016) :: 2006 F250 - Phaser Knock At Idle In Gear
Ok I bought this truck with a bad engine 5.4 3v had rod knocking. I rebuilt engine got it all back together and in truck. I did replace cam phasers and solenoids. After driving 20 mins or so it would start the phaser knock at idle in gear so I put a oil pressure gauge on it and cold had 55 psi after running 10 mins or so had 15 psi at idle then would drop to abought 9 psi. I am thinking I got bad cam bearings or something for some reason don't know why. I did it but I took oil cap off where you pour in the oil. Had to force it off it was pulling that much vaccum ones cap was off oil pressure jumped up to 25 psi. What could be causing this.
View 2 RepliesFord Super Duty (1999-2016) :: Shift Very Hard After Idle In Gear (stop At Signal) Occasionally?
So, in my 99 Bounder RV (F53 chassis), V10
I think it has a 4R100 transmission in it (I have not verified this).
I had the oil and filter changed about 10K ago.
Runs and shifts fine .... then I stop and idle with it in gear (say stopped in traffic for a few minutes).
Now the thing shifts super hard! I actually get rubber in all gears.
So I pull over, shut it off. Restart the unit and everything is fine again.
It does this very consistently!
I went to the local transmission shop. They said with 110K in an RV it could be anything and I should think about letting them rebuild it.
Now that is something I would do ... not diagnose a problem and just rebuild it. I thought a "professional" would actually look for the problem first.
I don't want to rebuild the transmission if there is small item that will fix this.
Ford Super Duty (1999-2016) :: 2011 F250 - When Start To Accelerate In First Gear Truck Goes To Idle For About 2 - 3 Seconds
I have a 2011 F250 with the 6.2 gas engine. I have been having a problem that the dealership says there is nothing they can do and have never heard about.
After the truck sits all night I get in and drive it for 10-15 min. It gets warm and I get out turning it off. When I come back about 15-45 min later I start it up and go to leave. As I pull out and start to accelerate in first gear the truck goes to an idle for about 2-3 seconds. I push the gas pedal and get no response. After a couple of seconds it picks up wherever you have the gas pedal. If you have the pedal to the floor it jumps you forward. This is not putting on any lights and the computer is not throwing any codes. According to the dealership the computer is telling them there is nothing wrong.
This has happened 12 times in the past 6 months. It has happened since I bought the truck. I have just started documenting it as of 6 months ago. It is not something I can make it do on command. After it happens once it doesn't seem to do it again for a week or two. I have 31000 miles on the truck. The dealership has had it for 4 days now and can't seem to get it to happen for them.
Camry :: 1999 - Idle Very Low Then Stall Completely If Try To Put It In Gear
We've brought our 1999 Camry to our mechanic twice for a starting problem to no avail because it never happens while it's there. So cliche right? About half the time it has trouble starting and the rest of the time it starts and operates fine.
These troublesome starts: * typically idle very low then stall completely if you try to put it in gear * sometimes, but very rarely, stall immediately * sometimes giving it a tiny bit of gas seems to prevent stalling * eventually, after 1-2 minutes, the engine begins running normally (usually i just sit there and wait and can feel the obvious/sudden change from idling low to a normal idle
It just passed the CA smog test and the mechanic couldn't find any problem. What should I do?
Ford - Explorer :: 2000 - Idle Goes Down To 900 And Then To 600?
I have a 2000 Explorer, 4.0 V6 SOHC w/ 135K miles. All of a sudden it has an idle issue that's driving me nuts and the dealership can't fix. It has been in the shop 4 times for this problem so far.
It accelerates and cruises great, but when I come to a stoplight, the idle goes down to 900, then suddenly drops to 600 and idles rough. The "Check Engine" light is NOT lit. There is no hesitation, backfire or any other running problem. I have had plugs and wires, PCV valve, IAC valve and MAF sensor replaced. Technicians have checked for vacuum leaks and intake air gasket leaks and have found nothing.
I can "power brake" it and smooth it out some and even turning on the a/c or defroster boosts the idle and works a little. Shifting to neutral or park does not raise the idle like previous cars I owned. I only drive this car back and forth to work, about 1000 miles a month, and I'd like to make this Explorer last at least 200K miles. We just got a Ford Escape and I do not want another car payment right now!
Ford - Explorer :: 1997 - Idle Too Low?
After replacing a faulty spark plug wire on my '97 explorer, I started the engine (4.0 liter pushrod) and noticed the idle much lower than it was previously- to the point it now borders on stalling. The wire I replaced was on the right side (if facing engine from front) closest to the firewall. I thought I may have worked a vacuum hose loose when feeding the wire under the intake, but I checked and checked and saw nothing amiss. What I may've did (if anything) to cause this problem?
View 7 RepliesFord - Explorer :: 1993 Won't Go Into Gear After Starting
I have a 93 explorer it ran fine then when I drove it today it stalled put it in park it started but wont go into gear when shifted?
View 1 RepliesFord - Explorer :: Engine Creaking At Idle
Background info: Had a blown head gasket and a mechanic used a sealant on it to patch it up. Car went from not turning on to running ok
Problem: at idle the engine creaks. It isn't a ticking or knocking but definitely more of a creaking sound. Can't figure out if this is safe for the car to be driven and what could be causing it.
I have a video of the sound .... Potentially a head gasket that was partially fixed maybe??
Ford - Explorer :: Air Conditioning Only Works When Car Is In Idle
Friend of mine said that the air conditioning on her 2001 Ford Explorer only works when her car is in idle. She said that when she steps on the gas the fan continues to work but doesn't blow cold air. If she stops at a stop sign it works... and so on.
She has taken it to a shop that specializes in air conditioning and he checked and cleaned off a few connections (whatever that means) and thought that would do it but it didn't. She is going to go back this weekend.
I told her that I would think that a specialist would see the idle/drive issue as a good clue as to what the problem is.
Ford - Explorer :: 2000 - When Cold Won't Idle / Tries To Die?
2000 Explorer with the 4.0 SOHC.
It starts fine under all conditions but when cold, like in the 30s or lower, it doesn't want to remain idling, yet no CEL comes on. New fuel pump. The throttle body is cleaned, as are the injectors. It runs super once it gets past the cold startup issue.
I was thinking a sensor is getting weak but not weak enough to set the CEL.