Hard start like it's not getting enough fuel then kicks in and runs great with no hesitations or issues and with plenty of power. Replaced fuel filter, nothing changed.
View 3 RepliesYes, another thread on an explorer that occasionally has trouble starting. One cold morning the fuel pump would not operate. When turning the key to run the volts to the pump (with plug disconnected) was 8.6 for a second, then dropped to the 6v range. I took the inertia switch from the firewall and back probed the wire going to the fuel pump, getting 12 volts. I went back to the fuel tank and measured the voltage with the key in run position, and read battery voltage. The car started, and has not failed in 3 days. I know it will quit again. I was thinking of replacing the inertia switch and fuel pump relay.
View 5 RepliesIt is a 2006 Explorer with the 4.0 and around 89,000 on the odometer. Around a couple weeks or so ago the wife said the explorer was hard to start one evening and it has been like that ever since. It cranks for about 5 seconds and then fires. So far it has started every time since this issue began. This is really the first issue we have ever had other than the radiator replacement a few years ago.
View 3 RepliesI've replaced the fuel pump and filter, plugs and coolant temp sensor. It starts after I spray starter fluid in after a few times and cycle the key on to prime the line but is still hard to start. It runs fine and it seems that as long as the engine is warm or (guessing) fuel is still pressurized in the line it starts fine.
View 3 RepliesI am having a random hard start condition. it will happen once a week or with no rhyme or reason. It turns over real nice but does not start until the second or third trythe last time on third try i push accel pedal to floor and it started. This hasn't happen in a few day so I cant tell you if the accel pedal will always work.
View 9 RepliesWe have a 94 ford explorer and every now and again it has issues on the start up. It will sound like it will want to crank over but just won't. If we wait 20 mins it will start up no problem. We have changed the fuel pump, fuel filter, ignition coil, and fuel pump relay but it still has this problem. Also occasionally the a/c blower wont turn on. Tonight it happened again and I pulled the fuel pump relay out and it was really hot, after it cooled down and was put back in the car started. I am beginning to think it maybe an overheating issue that is affecting the relays but am not sure. I was also wondering about changing out the relay box...
View 6 RepliesI have a 2005 Ford Explorer 4wd with 4.0 SOHC 6 cyl Flex Fuel. For months the vehicle has idle rough and increasingly becoming difficult to start. I decicded to replace the spark plugs and wires hoping to solve this issue! gap set to 052. When I started the vehicle it went into engine fail safe mode and wrench light came on. I then replaced the TPS on the throttle body and had no diference (I may have installed incorrectly! when I put it on the armature felt like it broke free inside the sensor). DTC codes read P0223, P2106, P2110 and with P0122 pending, P0223 pdg, P2106 pdg, & 2110 pdg.
With the old tps installed and wiring harness disconnected the truck will start in fail safe mode, but will not start at all with wire harness connected. A volt meter reads at computer end of wire plug 3.69 volts at pin one (gray/red wire +) and pin three (gray/white wire -) with key to on but not running.
After sitting engine cranks longer than it usually did before it starts. idles a little rough. engine light comes on after it been running about 30 sec for 1 min. after that seems to run fine.check codes po446 and p1633 always come up. if you let sit a bit with key on starts right up.replaced gas cap checked evap lines, and changed filter no luck. Did notice with lines off evap solenoid key off or on i can blow through it. that doesn't sound right.
Checked fuel pressure. key on jumps to 90psi then falls to 55psi and stays. turn off key and leaked off 10psi in 5 min.start engine while watching gauge does the same as when the key on except it falls to 30 to 35 psi and bounces between them. i think this is way low. What is the correct pressure? Shut off engine and drops to 20 in 5 min. Next I plugged line on test tee going to fuel rail and tested same results as key on. the convinced fuel pump was bad since regulator and check is there. replaced pump. problem still there.
I'm a diesel mechanic and know my way around Powerstrokes, this 4.0 is not what I would usually work on, but I have a friend who has 2006 explorer 4.0L SOHC, someone told him he needed a motor with out explanation why, so I didn't want to see him get ripped off. The problem is it idles very rough, hard to start, and stalls. There's no DTCs , if you hold the accelerator slightly it will stay running, but once you let off it will either idle really bad and misfire or cut off, once pushing the accelerator the rpms raise very smoothly up til 3500 which is what I assume the rev limit is in nuetral.
I've done checks with focom and forscan, I was thinking possibly a bad fuel pump, while monitoring fuel pressure I see a range of 289 - 326 kpa with 26% fuel pump I guess duty cycle would be the correct term(once again I'm a diesel guy, and use to dealing with IPRs and Hpops) not sure if the desired fuel pressure is relevant on these but it always stays at 269kpa. I believe that equals out to 40-48psi while I believe this system is supposed to have somewhere in the range of 60 - 70, but I wouldn't expect to get a rough idle with no load with almost 50 psi of fuel pressure.
So with no DTCs Im baffled, and don't want to start wasting money just throwing parts at it. I've thought everything from fuel pressure sensor, to coil pack(replaced 4 months ago) to crank and cam sensors.
I did end up getting a code p106, but I believe this is because I didnt tighten the intake hose after checking the throttle bottle, I just slid it back on. out of the 4 days of testing first time I seen a code pop up besides unplugging some sensors here and there to make sure the pcm would actually register a dtc.
I have a 2000 Explorer W/4.0 SOHC engine. With summer nearly over and fall on the way, I need to figure out what is going on with my engine. This problem has been going on for the past 2 years. As the outdoor temperatures get cooler, the harder it is to start and keep the engine running. This starts happening around 65 ambient temperature, and gets worse as the temps drop. By 30, I can barely keep the engine running.
Odd thing is, all I have to do if the engine starts is, keep my foot on the pedal to keep the engine around 2000RPM, put it in gear and start driving. After about a mile or two, the engine runs normally, and will do so the rest of the day. So far I have cleaned the air flow sensor, replaced the IAC, replaced all the injector "O" rings, and cussed a lot. I smoke tested the engine and the only vacuum leak is a very small one at the EGR valve.
Ok so I have a 1997 Ford Explorer with the 4.0 SOHC .. The girl that owns it went out and started it to warm up and went back in the house , when she came back out it had died and wouldn't start .. I hauled to our shop and started diagnosing it .
It has spark
has fuel
Timing is good
Fuel pressure regulator is good
Crank sensor is good
About 62 PSI fuel pressure
No CEL
Seems to be getting WAY too much fuel and fouling plugs !
Replaced ECM ...same thing .
Used NOID light on injector wire and I have never seen one get so bright !
I have a 2000 4.0 Explorer that sometimes will not start. It has happened on cool mornings as well as hot days after I shut it off, for example, shutting it off to fuel up. I always turn the key to the on position and wait a second or two before cranking, and when I do that, I can usually hear the fuel pump. It's when I don't hear the fuel pump that I know it won't start, and sure enough, crank and no start. My question is, is the fuel pump going out? Or another thought I had was maybe the inertia switch starting to fail? It runs great when it starts, just has a problem starting sometimes.
View 8 Replies2000 explorer XLT, 4.0L, OHV (VIN "X")---sitting for 15 months, engine turns over but no start unless 10 cc's of gasoline into intake manifold, then runs for 4-5 seconds. Fuel pressure of 5-6 PSI at fuel rail AFTER replaced fuel pump assembly and fuel filter. I can hear fuel pump come on for about a second with key on. Doubel checked fuses and relays for fuel pump and PCM, then again checked that engine would run briefly with gas squirted into intake manifold. Questions:
1) Could fuel lines be clogged after sitting for over a year?
2) Area driver's side next to spare tire, underneath jack storage, where return fuel lines are clustered (nuts are rusted and need to be sawed off)---some type of fuel regulator here? I thought fuel pressure regulator was on fuel pump assembly.
My parent's bought a 2002 Explorer 4.0 V6 very early, either late '01 or early '02 when it first came out. Besides the dash blackout (which I found a fix for, need to do) it's been plauged latley (since Nov/Dec 2010) with the intermittent issue of when... You turn the key on to start, you dont hear the fuel pump enguage, thus no start. Get towed, it works like a champ.
It's blown a fuse 1 or 2 times cause of this, had the fuel pump recently replaced (dec/jan this year) and just did it again. Our local Ford dealership figured the fuel pump went bad from sitting, the vehicle only has about 33k miles on it (dad dont drive much). What appears to be a bad fuel pump, only to have it get towed, or sit overnight and start like nothing ever happened?
Dad's ranting about not trusting the vehicle anymore, he's 80yrs old so I can't blame him for wanting to feel comfortable with knowing his vehicle should start, but it is a machine, they do break but we cant seem to get this fixed.
I have an 04 Ford Explorer XLT 4.0 Flex Fuel. There has been loss of power to fuel pump. Relay and fuse both good, replaced the inertia switch...still nothing. Could a FPDM (fuel pump driver module) have anything to do with this issue? Or what should I check next? I am definitely at a loss as to what the issue could be! I know it is fuel related because I used starting fluid and it started right up and run for just a few seconds, so that should rule out ignition I think.
View 3 RepliesSometimes after running my 94 Limited, it doesn't want to start - it does crank - like it's not getting fuel. I have found the work around and want to know if it would be fixed by replacing the fuel pump relay.
The symptom is just after starting, it starts to run poorly, and then dies out, then will not start at all. I use to keep trying to start it for 20-40 minutes and suddenly it seemed to work.
It seems the work around is to turn the key to on for about 5 seconds and then turn it off - then it starts and runs as good as ever.
So, is this a symptom of a bad relay? I thought I'd start there because of the cost of the relay is fairly cheap. 1994 Explorer Limited 4x4?
I have a recently rebuilt 400 with a mild cam and Tmeyers flat top pistons. The carb is a 600cfm edlebrock that was bought new and installed a few months ago.
The issue I'm having is if I'm driving around and shut it off to run in the store its hard to start when I come back. I end up having to floor the gas to get it to start. When it's cold I tap the gas and turn the key and she lights right off. Could this be an issue with vapor lock? Why does it go away if I floor the gas?
Only other thing going on is when accelerating the engine runs noticeably smoother above 2700rpm. It's a little boggy below that. Probably two different problems but I figured I would throw it out there.
I've got a 2002 Ford Sports Trac that won't start ! It will crank till battery dies but is not getting fuel. I have had it towed 4 times in the past year. of the 4 times,this last time it wont start. Every time that I have had it towed back to my house and dropped in the driveway it has started up with no problems. It will run for a few months or more.This last time it would not.
Could this be an electrical problem.Maybe loose ground somewhere or something else. Would like to rule out some things before investing in a fuel filter or fuel pump. Would hate to buy new FuelPump and that not be the problem. Can't find free wiring diaghrams for this issue.
I have a hard starting condition after warm up. It starts up fine when it is cold.After running diagnostics and coming up with no error codes, I noticed that I smell raw fuel after the car was warmed up and sitting for about 15 minutes. I believe this is the cause of the hard starting condition after warm up.
How do I test the fuel injector for leaking? I think it may be leaking fuel into the throttle body after sitting for a few minutes, causing a rich or flooded condition which makes it difficult to start after it has been warmed up.
My 302 runs pretty good when all warmed up. It has some cold start issues every now and then, but is easily dealt with. My question is how to best "tune" the carb. It's a 600 cfm 4150/60 style Holley single pump, vac secondaries and electric choke. About as basic as you can get. I think I have the fuel level set correctly. I also think I have the "idle mixture" set right. I used a vacuum gauge and moved back and forth between screws till I got the highest vacuum. Is there a better way than that? I have the idle set correctly. the fast idle is a little high, but I can fix that.
Now, my real question is how to fix the hiccup and stumble I get many times when I step into it pretty good. I assume that this is the point the carb is going from idle circuit to main circuit. It stumbles when I get on it real hard from a standing start. I can roll slowly and step into it and it stumbles as well. I also like to blip the throttle when I down shift (it has a manual tranny by the way), and many times I'll blip it and get nothing. Now, it runs fine after the stumble all through the rpm range. That's the only time it stumbles. so, do I need more accel. pump shot?? To compensate on the transfer of circuits.
I also notice when I on it real hard, during the shift right when I jump on it, under the heaviest load, I hear a bit of spark knock. It's not running hot, and the timing is good. Do I need a bit bigger jets? I'm thinking it's going a bit lead during that time, but I don't have any real way to measure it.
While the owner of 2 Ford Trucks, I also have a 2004 Ford Taurus with 28K on it. For a while now the vehicle is hard starting, cranks but acts like it is not getting fuel, however, I can hear the pump come on. Other times it starts right up, but a clicking sound can be heard coming from the firewall area. At times the gauges will not immediately respond when the Vehicle is started and then all at once they will begin to work. Now, my check engine light is on, but my hand held obd will not read it. All the terminal pins look great, obd tester works on my other two vehicles, cigar lighter working, the fuses i checked are good. Vehicle runs great. Can this all be related to a bad module?
View 1 Replies