The OEM M+S tires on their 18" wheels have been removed and replaced with 17" rims on which winter tires are mounted.Should I place the stored tires in garbage bags or anything?
View 15 RepliesI purchased a used 2003 Echo last week. The all season tires are on 15 inch rims. I would like to buy snow tires for this car. The question is - snow tires on 15 in rims or snow tires on 14 in rims? I understand that 15 inch rims was an option selected on the original purchase. Without this option, the car would have had 14 inch rims.
View 14 RepliesJust had new tires mounted and balanced on my 2011 Santa Fe. I purchased Toyo Celsius tires. I purchased the tires on line and had Faulkner Hyundai in Harrisburg PA mount and balance them.
When I drove to work 2 days later, I found that the vehicle starts to vibrate above 65 mph. When I get to 80 mph (typical traffic speed on I83 in the morning), the vehicle vibrates so badly that I shake in my seat.
This shaking leads to a feeling of lack of control. I'm hoping the dealer just screwed up balancing the wheels. Faulkner Hyundai uses a road force balancing machine.
My old near bald tires (the factory original Bridgestones) had a tiny vibration around 65 that went away as speed increased. With the new tires, the faster you go, the worse the shaking gets.
My 2011 Santa Fe still has under 30,000 miles on it!
I bought a set of new tires for my 2000 astro van and 1994 Saturn SL2 ::edit:: two summers ago. I bought a "full warranty" with the tires which includes checking the air pressure and free rotation. It seems every time I take the either vehicle back for a tire rotation there is a problem which is not covered by the warranty. For example I was told that each vehicle now has a rim/wheel which is slightly out of round with the implication that this negates any warranty on the tire.
I looked at the tire on my van as the tech spun it around while dismounted as you would a bicycle tire and sure enough the tire "wobbled" a tiny bit when viewed straight on at the treads - like a spoked bike tire would if it needed "truing". I was given a speech about "driving to hot" with steel rims and alloy rims were better as they tolerate heat better, also they mentioned the weight of tools in my van but I pointed out that any two of their hefty employees weighed much more than anything I ever carried in my van. The implication again is that this could negate the tire warranty.
I have driven since the 1960's and this is the first time I have ever had a problem with rims - even through minor accidents. The most I have done with these wheels is to bump them on a curb in a parking lot occasionally.
I have a Ford F150, 2003. I replaced the switch above the master brake cylinder just a few months ago soon after I bought the truck. I put 17" rims and new tires on my truck and now my cruise control works intermittently. It worked fine before then.
Can there be a connection between the intermittent failure of the Cruise and the larger rims and tires? I know my speedometer is off by about 4 MPH at 55 but I expected that.
My wife's 2001 Chrysler Concorde can't seem to keep the air in the tires due to leaky rims. Mechanics say they are pitted and that's the best they can do. They have used rim sealant. Can I just use tire tubes until we get rid of this thing?
View 5 RepliesI have a stock 2012 F250 6.7 Diesel. I was looking at getting new 18 or 20 inch rims for it and was wondering what the largest tire I could fit on those without rubbing on the truck would be. I know there are lots of topics on this but I could not find anything that applied to me. Most topics were on stock wheels.
View 1 RepliesHad my winter tires put on today and the tpms warning light came on. Tire pressure is ok. Never had this issue before with these tires/wheels. This would be the third winter with them. Is there a way to reset the warning light on a 2010? I have read about doing this on later models but nothing on the 2010. I do not have vagcom tools. Hoping I do not have to take to dealer.
View 4 Replies2007 Passat wagon with TPMS. Getting new sensors and a set of winter tires and wheels.
Can I ad the new sensors the my Passat using a VagCom or some other method?
Not long ago I fitted after-market rims to my 2006 Passat 2.0 FSI HighLine, I changed from 215/55/16 to 235/45/17 with Falken ZE912 tires, all new. The center hub of the Passat is 57.1(as far as my knowledge goes) and the wheel hub seem to be 66.6, the shop who installed my rims inserted a 57.1 to 67.1 poly-carbon hub rings which needed some force to fit into the wheel, the vibrations did not stop. All 4 wheel&tires were balances 2 times on one machine then a third time on a different machine just to be sure, still the same. I didn't preform a front alignment yet as i didn't believe it's needed, although right now ill try anything...
Anyway i then measured the rim hub diameter which seems to be 66.6. I bought a set of 57.1 to 66.6 poly-carbon rings, they also needed a bit of force to fit in the wheel, still there is no improvement and the car vibrate under acceleration. I would like to add at this point that i had no vibrations what so ever with the old rims and tires even though the tires were quite worn. I am thinking maybe i need the 57.1 to 66.1 size? Or perhaps i should use aluminum rings instead of plastic?
Is a size difference of 0.5 can make that much of a difference? I know an aluminum ring wont fit unless its the perfect size, and plastic are a bit more elastic meaning like in my case, they can fit in a smaller rim with a bit of force. Should I aim for a ring that fit perfectly without the need of applying force? Can it be that a 66.6 ring, fitted in a 66.1 rim is not eliminating the vibrations just because its off by a 0.5 mm and needed a bit of force getting inside?? I though that as long as the ring fits inside the wheel it will work but obviously its not..
Yesterday, I swapped my OEM 18" setup for new 17" winter wheels and tires (set at 37.5 PSI at 55 F)). Today I drove 30 miles and then my TPMS light came on (Temp=36F). Pulled over, checked pressure - all tires at 36.5 PSI.
View 6 RepliesI have a 2007 King Ranch F250 that had 18" rims on it. I just put a new set of 2008 KR 20" tires & rims on my truck and now the ABS light is on. Does increasing the tire/rim size mess with the ABS? If so how can I remedy this?
View 1 RepliesI just got new rotiform BLQ rims and nexen tires. I have the hub rings and the setup was balanced and aligned (double checked).
Before this I had 3 bent TSW rims and got a pretty bad shake in the wheel around 65-70 mph. Before or after that speed everything is smooth now.
Why would this shake still occur.
I Just did a little work on my 2013, lowering springs, BBS rims and Kuhmo tires....
I now get a Check Tires warning every-time at start up.... Clearly it has to do w/ the lack of tire pressure monitors...
Can this error be whipped/cleared? OR do I need to get TPM's? OR do I live w/ it?
Current Situation: I got my winter tires put on last week. I use the same rims for both sets of tires.
Problem: Driving out of the repair shop I noticed a sound coming from the front right of my vehicle which wasn't there before. I kept it off the road and made an appointment. They saw it today and said the right front wheel bearing is shot.
History: I got both axles replaced last year due to super worn out CV boots.
Possible complications: The first shop I went to (Auto Express in Amherst MA) did a crap job, and the clip holding the axles in place came off while driving. I didn't trust them at this point, so I had it towed to XYZ to get it put back on. No problems since.
Question: How likely is it that the mechanic at XYZ did something to cause the bearing to wear out suddenly? The noise started immediately after the tire change and was clear and noticeable. It was not there before.
Car: Toyota Camry with 147k miles on it.
I had terrible issues driving in the snow /ice last month. The car literally would not move forward. I bought 4 new Michelin Tires (Weatherwise II) but am thinking I should put on Snow Tires. Can I put them on the front only since the car is FWD? Also, which tire to choose?
View 11 RepliesThought I would check and see if it's possible to store a Carburetor. Have a Holley 4160 that I rebuilt and would like to keep as a backup. Thought since the carb has not been installed the gaskets and seals may not be an issue. Other option, swap the Carb on my truck every few months.
View 4 RepliesAfter setting the climate to 70F, Auto, and driver controlled for all occupants, start-up volume adjusted, e.t.c, I press the "STORE" button under the user profile settings. The key has been synced.
Every time i start the car up, it maintains these settings. If I press the big round knob on my name, it goes to these settings (my name, and assigned key icon)
However, if Im driving, and lets say, i adjust the temperature to 76F, then maybe later starts to get too hot, or cold, and I want to go back to my stored setting, it does not, it just stays on the new temperature. If I change the temperature manually again (2nd time), and I press the stored setting, it goes back to the setting i just had, which should NOT be stored. It usually just ignores the stored setting.
I also noticed that you can either press the large round knob, or the bottom right tap button where it says "SELECT" for your stored settings.
Had my first hiccup, and it's little disconcerting. Usually about every two weeks I take my car through a car wash and I have to put the car in N-no big deal, no messages.
This go-around as I was nearing the end of the wash, the Master Warning and the traction battery lights gets thrown, with the message on the display saying I should put the car in Park. Well, naturally you can't do that inside this car wash, so I waited until after I exited and checked the charge display: one purple bar.
So I hit the freeway and within 5 minutes I go all the way up to all Green. So I go from one bar to almost 8 bars in under 5 minutes? I find this rather odd that all of a sudden I get this behavior.
Here's my question: when this happens, does the car store a DTC code?
I have a 05 dodge Ram that periodically wont start after I stop at a store etc. It happens about once a month and will start up after sitting for 1-8 hours.Ive had it to the dealer , diesel mechanics, etc. with no luck,( Cant reenact the problem and nothing shows on the computer).
View 7 RepliesOn my 2004 5.4 I have removed my right cylinder head for replacement. There is a sensor on this head beneath the intake manifold. When removing the sensor I turned the plastic connector about 1/4 turn or less prior to turning the actual sensor. What sensor is this and would I have broken it by this mistake? It did not make a sound, it just turned a little on the base of the sensor.
View 1 Replies