I started feeling a slightly rough idle three days ago and yesterday the check engine light illuminated. When we read the OBD, it indicated a Cyl #1 misfire. Question is this. Can I replace a single coil pack (1/cyl), or do I ahve to replace all 8 as a set and why? 2000 Ford Expedition 5.4 L cyl misfire.....
View 4 RepliesThis has been an issue for about 8 months now. I'm getting a misfire on cylinder 4. So far compression test, new gas filter, fuel injectors cleaned, spark plugs and wires replaced. coil pack replaced. Heater valve was leaking but was replaced.
View 10 RepliesOK, got a check engine light today when I fired up the Ranger.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use?
Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
My parents 2000 Ranger has an CEL for cylinder 4 misfire, but it will clear on its own and then start up days/weeks later, is this common? Could it be an injector?
View 3 RepliesI have a misfire mystery going on in my girlfriends 00 ranger. What is going on, is there is an intermittent misfire on #4. I have an ultra gauge hooked to it, so most of the time when it does it, it will flash a pending code. A lot of the time, the pending code will go away, but sometimes it will set the PO304 code.
First I tried a tune up. New plugs and wires, air cleaner, cleaned out the throttle body. This cured it, for a short while. Then we were back to the pending code / setting code for #4.
When I pull the plug on #4 it is sometimes wet with gas. If you put a new plug in it runs fine for a while. In fact the last time we took a several 100 mile trip with it right after plug change, and it ran great. The pulled plugs re always in good condition with no burn, oil, chips or glazing. I have been using the standard autolites that are in advance auto's computer for that engine. No issues with the other 5 so I figure they re good enough.
The day after we came back I get the call... Honey its doing it again. Often to the point of having no power at all.
But it will clear itself usually, if not a new plug for #4 will cure it immediately.
So I thought something is killing this plug.... Or flooding it. SO I ran 2 cans of sea foam though it, put in a new plug and an new wire. It fixed it for a week then it did it again.
Ok I think... maybe the coil pack is bad either killing the plug or just not firing it at all? So since the pack has never been change in its nearly 300K life (to my knowledge, shes had the truck since about 60K) What the heck.... a new coil pack for the old thing.
I have not had the chance to clean the MAF but we are talking misfire on one cylinder, every now and then with no real conditions that set it off. More often than not its a pending code that you can even hear or feel and other times its a full blown miss that drags the truck down. Well for a short while until it clears up or I replace the plug.
3 cans of seafoam surely would have cleared a sticky injector. I realize it could be a bad wire to that injector but I have not had the time to tear the fiddle bits off to get to it to clean and test it... or just replace it.
Honestly Ive had a lot of cars and trucks, I don't remember ever having to replace an injector. Ive had bad wires to them but they misbehave ALL the time. This problem is so intermittent its freaky.
She says it does it mostly when its cold or not totally warmed up. Almost always, by the time the engine is hot it goes away.
And hot for this truck is over 185F, which I think its too cold to be running and the thermostat needs changed BUT she thinks cool=good. I keep telling her no, cool is often not good, the engine needs to be up to the operating temp.... which to me means 190-200. Her ranger runs between 170-180 all the time. I doubt thats causing the problem but still.... I think new thermo is in order.
My thinking is since it runs so cool all the time, the issue might be related to a spike in the temp over 180 ish, that gods forbid is opening a crack somewhere to suck air or lose compression.
And a compression test is my next step on #4 if/when it does it again. Now I have had cracked valves before, I don't recall them acting this way. After all sometimes the thing will go 100s of miles under different driving conditions and run fine. I don't think a cracked valve would be that nice.
Shes getting @18 MPG mixed driving, when it runs t runs like a bear. It always fires right up. There is no smoke, white or black. There is no water in the oil, no oil in the water. No audible exhaust leaks. No ticks knocks or oddball noises. For its age and miles almost 300K it runs perfectly.
Well until it has its intermittent issue with the misfire, that isnt bad enough to actually set the code.
I have a ford Ranger with a 2.5 and 231,000 miles. I bought this truck with a misfire on #1 cylinder. drove it home and started it a couple days later and still misfire on #1 but as soon as you rev up the motor the #2 starts misfiring as well and dies. start it back up and misfire on #1, rev up the throttle and misfire on #2 also.
Here's what i have done so far. intake gaskets, plugs and wires, checked fuel pressure (good), swapped injectors on 1 and 2 with different injectors, timing belt, tensioner, swapped coils from primary to secondary no change, checked compression and all 155 and above.
I have talked to everyone i know and am getting no where. the truck can sit and run for a hour with a minor misfire on #1 but as soon as you hit the gas it starts another misfire on #2. I am thinking it is a ecm issue.
Well, I have been through the tech folder and all over the forum reading but cant seem to come up with a good first step. When i accelerate the truck shakes, by the sound it seems that its missing a cylinder. I guess it could also be the motor mounts. Besides replacing the plugs and coils, is there something else that could remedy a misfires or dead cylinder?
View 7 RepliesI recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 RepliesOK, got a check engine light today when I fired up the Ranger. Like I posted previously it is running kind of rough so guess I know why now.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use? Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
I have a 2000 f150 5.4 liter engine. I traveled about a month ago and while on the highway it started "bouncing/shuttering" really bad. I pulled off and while still in drive but completely stopped it was still bouncing but when in park it stopped. I took in into the Ford dealership and they said that cylinder 5 was misfiring and it was losing pressure fast. Then it stopped acting up completely and they couldn't find anything wrong with it.
Well about a week ago it started bouncing again on city roads (no highway). The check engine light came on and Orielys said it was a cylinder 5 misfire. Also, under the oil cap and in the tube where you would put the oil in has a yellow thick substance on it. I know that it is water in the oil. Also, there is a black "gunk" not far from where you would put the oil in. Could these problems be connected?
I've got a misfire problem with my Focus. It started about a month ago and did not trip a code until last week. It stumbles on acceleration between 2,000 and 4,000 rpms. It is only a slight stumble and although noticeable, it does not impede driveability much. Last week I was able to get it to finally trip an OBD code. P302 - Cylinder 2 misfire. I changed the plugs and wires with no effect. I thought I had it narrowed down to the coil or injector until my wife noticed a new wrinkle.
Under normal driving conditions the misfire is annoying, but my wife found that if she turns on the A/C, it is undriveable and will not accelerate past 30 mph without some patience and a neck brace for the bucking. My first thought was the A/C compressor was freezing up. I turned off the A/C and left the blower on and it would not stop missing. I turn off the blower and it smooths right out to the annoyance I described first.
Right now I drive the car without A/C and blower whenever I accelerate. If I'm going a steady speed, all is well and I can run the blower and A/C.
I have a 2000 Explorer 4.0 SOHC that I'm having a persistent problem of cylinder 3 misfire. I've changed plugs with Motorcraft plugs set to the proper gap, put on new wires and have checked the resistance across the ignition module, both primary and secondary without change. I doubt that the problem could be the ignition control module as only cylinder 3 is affected. I have Auto Enginuity that I use to read the codes, attempt a repair and then clear the codes only to have P0303 appear again. Obviously the engine stumbles and has poor acceleration.
View 14 RepliesComputer also said to replace Camshaft position sensor. The plug is getting spark and appears to be getting fuel. the plug was moist not dry. How ever i did notice the egr pipe is completely broken free from the header. Which I am replacing. Since it is reading lean on bank 2 could this alone cause more fuel to be dump in the cylinder 2 cause the plug to be too wet to fire? if not what might the possible problem be? 2000 Ford Explorer 4.0L ...
View 7 Replies2000 4.2....Last year I had to replace the coil pack when it started running rough and had a code for a misfire on cylinder 3. It is doing the exact same thing now, same code, same cylinder. Is there something wrong that is causing this?
View 5 RepliesI have a 2004 Accent Gt with only 43k miles on it and I am getting a cylinder 4 misfire when I refuel. I have replaced the 4 spark plugs. The original code was random multiple and now it is just cylinder 4. I tried to swap 2 spark plugs to see if maybe there was something wrong with the plug but the misfire did not move to another cylinder. I've read about maybe swapping fuel injectors, where I can find directions on how to do that?
View 8 RepliesI have an 02 Accent 1.5L that has a misfire on #3. I have replaced the head gasket, valve cover and gasket, intake gasket, timing belt, yes it was top dead center, MAF, Charcoal canister sensor, MAF, plugs, wires, coil pack, injector #3, and the compression in #3 is 130. What else to check. No other codes.
View 3 RepliesSo I have A 2000 Chevy and i keep getting a code saying i have a misfire on cylinder 8. i have replaced the spark plug, i have replaced the coil. this code is still showing up. what else could this be?
View 2 Replies2004 Hyundai Accent has is misfiring, after warming up, only in idle. This only happens after about 30 seconds in idle. Could it not be getting enough gas? This being said I was getting misfire on 3 as well but that would happen all the time and cause the entire car to shake. This problem is now fixed and only #4 is causing me problems.
View 2 RepliesCar threw a multiple cylinder misfire, changed plugs, wires, and then coil packs. Code keeps coming back.
View 12 RepliesAbout a month ago my wife's 2000 Jetta with the VR6 engine in it started acting up and throwing codes. The codes it threw were for random misfire, misfire in cylinder 2, and misfire in cylinder 5. Starting out, we changed spark plugs, fuel filter, and made sure the injectors were clean.
The problem didn't go away so we water tested the coil and wires, but they passed that test. The wires were quite old and out of spec, while the coil was in-spec across all terminals, according to the vehicle service manual, so we installed some new OEM leads this weekend. While installing the leads we noticed a disconnected vacuum line and reconnected that as well.
The vehicle was driving great for two and a half days, then today while I was sitting at a stop light, it started missing really badly and felt like it was going to kill. It did this for about 5 seconds, then recovered and ran smooth for about 5 seconds, before getting really rough until I started driving when the light changed. It didn't do it when I drove it a few hours later at all. This episode didn't throw any codes either.
What could be causing this issue? Would the MAF cause the intermittent missing, or is it possible that the computer is going bad?
I have a 4cl- 2000 Honda Accord about 160,000 miles on it. I have been having a shaking problem with my engine when it starts up after warm. If I drive more then 20 minutes, stop my car, to say go run an errand, and then come back and turn it on, it shakes and sometimes stalls out. I notice that the RPMs don't go above 1000 and waiver below that. When I do get it going, I have to tap on the gas a bit to get it to regulate. On longer drives after I stop it, it won't start and have to leave it sit for about 20 min. and then get it started by tapping the gas.
The check engine light that did come on has been checked as a cylinder 2 misfire. Sometimes it will flash and sometimes it will not come on.
I have new wires and spark plugs. A 3 year old timing belt. No vacuum leaks or gas line leaks. (all been checked by a mechanic).