Ford - Escape :: 2005 - Reverse Won't Work After Transmission Rebuild
Aug 20, 2014
I have been having transmission problems in my 2005 Ford Escape due to my torque converter coming apart so I took it to a local transmission shop for a rebuild. After 2 days it was ready and I took it home today. I put it in reverse once and it was fine but the second time I tried to back out of my driveway it won't go into reverse. It will go forward though. His shop is closed and I am going to take it in tomorrow morning. I have a warranty but it says I am responsible for labor. Is this something I should have to pay to fix if it happened the same day I picked it up?
View 8 Replies
Advertisement
I rebuilt my 4r100 myself. 1st time I re-installed it, I had no 2nd gear. All other gears worked fine. Drove it less than 2 miles.. slowly..
Took it back out, found i built the Intermediate Clutch wrong. Fixed. At the same time, found a stuck valve in the accumulator VB, Fixed that, at least i think I did. all the valves snapped back under spring pressure.
Put the trans back in, Drove forward, all forward gears work. Drove 10 miles normally, w/ some time spent in all speed ranges. Temps good, outside temp was 73F
M1 = i get good engagement and engine braking
M2 = I get 1st and 2nd, seems normal
OD = Normal shifts, 4th is a little soft, but always was.. TCC lockup good
OD (Cancelled) = Normal 1-2-3, with lockup in 3rd Worked the button multiple times, shifts down, and back up normally.
N = No movement, no creeping.. Normal.. as far as I can tell.
R = No reverse, or is binding in reverse, not sure. worse when up to temp.
P = Normal, no learching or creeping.. No stalling.
The OD light never blinked, so I don't think it is electronic..
Since M1 works and holds with engine braking. L/R clutch and seals are ok. Forward clutch is ok since i have ALL forward gears, No slipping that I can tell. no creeping in Neutral, so the clutches are not fried.. New fluid is still perfect. I'll have to re-pull the pan to see if there is anything on the magnet. I think it could be some stuck valves in the VB also.
View 9 Replies
So I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
View 4 Replies
I recently got an Escape and I am having a issue with the cruise control. That being, it doesn't work. The control module under the hood is all hooked up, the linkage the the throttle body and all. No broken cables.
The brake lights work as intended, and only when the brake is applied. On the inside, the dash-light cruise indicator works fine.
I ran the diagnostic by holding the off button and turning the key on. The cruise light flashes and I begin the sequence. I noticed I was pushing the brake out of habit while running the first few tests. They all returned 2 flashes upon completion of the diagnostic. All other buttons were registered.
Now the strange part, when I took my foot off the brake and did the same test, the final result is three flashes of the cruise light. I understand these flashes represent a fault, and I am having a hard time as I cannot find one.
What do these results mean? I'm thinking the brake being applied gives a fault surrounding the fact that cruise is disabled when the brake is applied.
View 3 Replies
2005 Escape CD4E gone...157,000 miles. Previous owner said it was slipping when shifting to 3rd. During test drive the vehicle would hardly move. Only code was for the output shaft. There were metal shavings on the sensor magnet as well as the magnetic drain plug. The drivetrain is now out of the vehicle.
Questions:
1. After a bit of research it seems like there are a lot of tweaks that should be done during a rebuild to make this tranny live longer. Is there any point to having a local trans shop try to rebuild it?
2. Given the reputation of this trans I assume it makes no sense to look at used ones, correct?
3. Any other options?
View 7 Replies
My reverse sensors have stopped working. As soon as you put in reverse, the on off button will light up and be telling you that it is off. What is going on and how do I correct this?
View 3 Replies
Rebuilt trany after losing all gears filled the tranny and while cycling through the gear everything seemed to fine took it around the block topped off the fluid and went for a drive and it will not shift out of second and i lost reverse. What did i do wrong?
View 5 Replies
I have a 2005 f150 xlt. Ext .cab I never changed the transmission fluid and filter
I have a problem now, the transmission do not go forward only reverse.
View 7 Replies
I have a 2002 7.3 e350 quigley 4x4 Sportsmobile with 312k miles. 2nd owner. Bought it with 295k miles 2 years ago. From what I gathered the tranny is original.
After reversing at a downhill angle, stopping, and shifting the lever to Drive, the tranny doesn't seem to put Drive in gear and depending on the angle of the slope, the van will roll back or barely creeps forward even with throttle. Put it in 1st gear, and the tranny engages that in gear and drives forward no issues, then I can shift to 2nd, then Drive and the tranny shifts fine after that.
No weird tranny noises or clunking. Noticed this issue about a month ago or about a couple thousand miles ago. Did tranny service (drain, filter, fill) at the ford dealership at 305k months ago.
I can only replicate this issue when Reversing on a down slope. On a flat surface van Reverses and engages Drive like normal.
View 7 Replies
I was wondering should I find metal in my pan after a rebuild on my AOD? It's been about 4 months since the rebuild and i took it in to have the fluid changed at another shop. Now the unit is doing fine but I did let the shop that did the rebuild know what was found.
View 14 Replies
I'm a proud owner of 2005 Mustang GT, 4.6L with an automatic transmission. Intermittently for the last year or so (maybe once every 3 or 4 months) its been shuddering when in reverse. Today it ramped things up a notch. :-/ The shuddering was pretty dramatic when I was trying to back out of my driveway, I shifted into park for a moment, then back into reverse, and it seemed to be ok. Then when trying to back into a parking spot this afternoon at work (in a parking garage with a small incline) it lost power almost entirely in reverse, lightly pushing on the gas just caused the car to shudder and not move anywhere. I shifted into park, and then back into reverse and heard an audible "pop" (my windows were down, but they hadn't been earlier so I'm not sure if this happened in the morning) and the car did not want to reverse. Rather than risk further damage I decided that it was parked relatively ok (90% in the space, eh good enough) so I stopped.
View 4 Replies
Ford AOD in 1988 F150. It's my first time rebuilding a trans and after install will not roll in neutral. I guess this is part of the learning process but I really need to get this fixed.
View 9 Replies
Pulled transmission out and it needs to be rebuilt front to back. My motor is generally stock but I'm rolling on 37" tyres so I'm thinking a stall converter and a "performance" rebuild. Looked at "Monster in a box" from Monster Transmissions. Truck is used at tymes to haul cement and heavy bed loads.
View 2 Replies
So last night my trans have out, going up a slight grade, all of a sudden the engine revved and I had no more 3rd gear. I've done some research, looks like rebuilding it is the only option. I've got my Mustang GT to drive in the meantime, so I am thinking of rebuilding it myself. The truck is an '07 F150 5.4 2WD.
View 7 Replies
I have a e99 7.3. had the transmission rebuilt a couple weeks ago by a local shop. have been getting some hard shifts between 2nd/3rd when lightly accelerating. Took it back already but they couldn't find anything. I am planning on taking it back again but what it is so it gets fixed right. What is causing this or what it might be? Should I be worried about having this shop try and fix this?
View 1 Replies
Still having issues with the transmission on my 05 F350. I posted before that it would take a few seconds to go into drive or reverse. The fixes were to change filters and do hot flush. I had the dealer do a hot flush, and then I put about 1000 miles on it. That didn't seem to fix anything, so I went back in and asked for more info. They did not change the filters. I thought they did, but found out they did not after the fact, so I decided to change the filters myself.
The interior filter was easy to change. The fluid was clean, and the magnet had shavings on it but nothing that seemed extraordinary. The exterior filter is impossible to get off. I reviewed posts on here before trying, so first was the impact wrench, then the pipe wrench, then the pipe wrench with a block wedged in to keep the thing from bending, still no luck. The cast nut broke off well before the pipe wrench came out of the drawer. How to get that thing off. I read on here somewhere that no fluid goes through that until 180 degrees, is that correct?
Scanguage says it rarely goes over 160, except for last evening when I was stuck in traffic. It went to 187, with ECT at 208. During this period, traveling under 40 most of the time, the transmission was shifting erratically, to the point I wanted to pull over and allow it to cool down. But traffic broke free, speed went up, and temps went down. Shifting returned to normal, except when trying to engage drive or reverse. The 3-4 second delay persists at any temp, and there doesn't seem to be any slippage. Just delayed and sometimes hard engagements. I'm at a loss for whats wrong.
View 1 Replies
I have a 1997 ford ranger 4x4 5 speed manual. We are rebuilding the transmission ourselves, and taking on the task has been pretty hard. We are stuck at the input shaft. How to take the input shaft out? Do you need a special tool?
View 1 Replies
I have a 1989 ford f150 xlt lariat it has a 5.0 and a 5 speed and is 4 wheel drive. Any way I am looking into rebuilding the rear end of the truck the pinion shaft has a lot of play in it up and down and both outer axle bearings seem to have lots of play in them. I believe it is a 8.8 inch in the rear. Just wondering if there hard to rebuild or what it all entails I have never taken one apart before and want to know what I am getting into. I have access to a press and a pinion and carrier bearing puller. the axle bearings i have done tons of them but never had to pull out the carrier. wondering how to set turning torque and backlash etc... and torque specs for everything.
View 8 Replies
Transmission rebuild? I seen a few threads where people talk of it but no follow up. I've heard it takes special tools but then so does a lot of things we shadetree on our own....
View 14 Replies
1994 E4OD Transmission.
Transmission was slipping terrible after vehicle warmed up. After feeling around for thoughts, it was suggested by numerous people that the transmission needed an overhaul.
Upon Disassembley the clutches were found to be excellent. They are actually thicker than the new ones in the kit. By .015" actually. Quite impressive considering they are 20 years old.
So now, I have kind of lost direction. If the original clutches are thicker than the new ones, and don't show signs of wear. What does that mean?
The fluid is pretty good, and there aren't fragments of metal. Nor is there any metallic shimmering to the color. It doesn't smell burnt or rotten either.
I have drained the torque converter and filled it with gasoline. I am going to spin it and hopefully knock any sediment loose.
[URL]
View 6 Replies
2004 Ford Taurus - transmission was going out last Aug - had it rebuilt (new seals and torque converter) got it back steering wheel was slightly off (1/2 inch) of being the center when driving straight. Took a while to get it back to the shop - life happens - took back today - said they did everything they could and really needs an alignment which they do not do - drove it home after hanging out at the shop for 5 hours. The steering wheel is now off 2 inches from center and the car is pulling noticeably to the right. Going back tomorrow - but they are saying that it was not them and that I need to pay for an alignment.
View 3 Replies
