Ford - Brakes - Escort :: 1996 - Grumbling Sound After Front Pad / Rotor Replacement
Feb 15, 2011
The shop replacing my front tires advised me to replace my front brakes and rotors soon. I'm not a huge car repair person, but I remembered my father-in-law saying brakes aren't that bad to work with. The car is the "college beater" I bought ten years ago and I'm trying to keep investments in it minimal. I told the shop I would do the brakes myself. So I spent the weekend with the Haynes manual fussing with overtorqued lug nuts, rusted on rotors, tightly wedged guide pins, and outer pads that didn't seem to have room (not the piston side). Got everything assembled, bled the caliper that was disconnected, and took it for a test drive.
I got about 30 feet from the driveway before pulling back in. The front of the car was making an grumble sound and had an odd vibration like a flat tire. This was with brakes engaged and not engaged. The car stopped fine, but I probably didn't get above 10 mph. Is this part of the "bedding/seating" process? I put in new (cheap) rotors and pads. This afternoon I'll check to ensure the pads are in properly and aren't dragging on the rotor and that I have the wheels properly centered. Car is a 96 Ford Escort 2 door hatchback.
View 2 Replies
Advertisement
I'm trying to replace the front brake rotors on a 97 Ford Explorer (AWD, 5.0 L). I've removed the calipers and pads - but can not loosen the old rotors. It looks held on by rust - but do I need a special rotor pulling tool?
View 8 Replies
My 97 f150 had been sitting for a while and after a few miles I could smell brakes and the left front rotor was hot. So I removed the caliper to see if I could free it up. When i push 1 piston in with a C clamp the other one comes out and visa-verse but I cannot push both in with 2 C clamps. When I push the brake pedal they both come out. Its like there is a check valve in the line. How should I go about trouble shooting this?
View 1 Replies
Looking for really good ceramic brake pads and rotors for my 2013 Honda Accord LX? I use my car for everyday driving in the city and highway and was hoping to find something that works well in all weather conditions including snow.
View 19 Replies
2008 F-150 2WD
How tight should the wheel bearing retaining nut (sealed bearing hubs) be torqued when replacing the front rotors?
Is there a spec, or just real good and tight since the bearings are sealed units.....
View 1 Replies
I have a 1996 Ford Escort with ~128,500 miles on it.
When I start the engine (either cold or hot), occasionally the engine will sound like it is missing and, if I step on the accelerator to give it more gas, after ~10-15 seconds the engine runs fine and the problem disappears. The engines shuts off if I don't step on the accelerator.
This happens approximately 3-4 times per week and I drive the car every day. I never know when the problem will arise.
I took the car to a Ford dealer to have it looked at and the mechanic, without doing any testing, said that it was either a leaking head gasket or a cracked head. The mechanic later then ran some tests upon my request and confirmed that it was not a leaking head gasket or a cracked head. No further tests were performed at that time, so I still am left without any definitive answer as to what is causing the problem.
View 1 Replies
I can't figure out how to get my front brake rotors off to replace them. I removed the caliper and thought the rotors should just come right off but they didn't? I then pulled the hub out and there was a retaining ring with a good size nut behind it , but you shouldn't have to remove the hubs to remove the brake rotors should you?
The stats of the truck are 04 f250 4wd w/manual hubs!
View 14 Replies
I have a 96 ford escort, 1.9. Recently I've noticed I get a pretty good vibration coming from the front end.
The vibration only occurs when I'm accelerating over 50. When I decelerate over 50 the vibration goes away.
What could be causing this?
View 9 Replies
I was driving on a short business trip and I noticed what I thought at first was clutch smell, and then I realized I had a brake overheating. I pulled over and the front right rotor and hub were very hot. The caliber not so much. I let it cool while I was at the meeting. About 1 1/2 hours later I jacked the truck up to see if the bearings felt bad. Seemed fine so I drove home trying not to use the brakes and the heat did not return. I replace the caliber with one from Ford, but the only lines I could find were from CARQUEST and they are made by Raybestos. I am assuming that these lines are made in China.
I have been looking for some braided SS lines, but can't find any for a 2 wheel drive dually with 4 wheel ABS. Where I can order some better lines???
I hated my old 1994 F-350 that had those Metal/rubber pins, they would mess up and overheat also, I thought that my 2000 would not have this problem, I was wrong.
FYI, about a month ago I replaced the rear pads, and changed all the brake fluid with Valvoline synthetic DOT 3. I installed Akebono pads on the rear and just today Akebono on the problem front side. Will change out line and pads on driver side later this week. I hope I got if fixed.
View 10 Replies
My front disc brakes are creating a small amount of drag on the rotor. With the car jacked up and wheel off I am able to easily turn the rotor by hand, but there is a small amount of drag. I haven't had any problems with my brakes, they have never frozen or overheated, etc. I put new brake pads and rotors on the front about 6 months ago only because it was time for replacement. The question is: how much disc brake drag is acceptable? Looking around on the internet for answers there doesn't seem to be a consensus: some people say absolutely no brake drag, some say that a small amount is normal. What do you think?
View 6 Replies
My front left rotor is warped and makes that annoying chirp chirp chirp sound as I'm driving. I hear it while the truck is driving and also when braking. I jacked up the front left tire under the control arm, removed the tire and caliper/pads, tightened the rotor against the hub with the lug nuts. Watching the bottom of the caliper mount as a reference point, I can clearly see the distance changing between the rotor and the mount as I rotate the rotor.
And I feel the resistance as the rotor gets closer in that spot. Is this simply a warped rotor? Or is something else causing this? I replaced the pads, rotors, front brake hoses, front left caliper and , still the chirp remains. The pins are greased and slide nicely. I also bled quite a bit of fluid out, since it was a bit dark compared to the new fluid. I checked for play in the tire, thinking maybe a bad wheel bearing, but found none. No other noises or symptoms in the front end.
View 3 Replies
I own a 2010 ford f150 that make a grumbling sound when i turn. the dealeship has replaced the clutches for the limited slip rear end 2 times now and it is happening again. they told me that the ford engineers are working on the problem but they do not have a fix for it yet. So they told me to just drive it with the positive traction engaged until they get a fix for it. Not exactly the answer I was looking for.
View 14 Replies
50 V10... How to tell if the grumbling sound when under a load is the posi plates? If so, how to replace them.
View 8 Replies
I want to remove the spark plugs but unable to loosen them. How I can easily loosen them up without breaking them?
View 2 Replies
I have a 1996 Ford Escort that was giving me problems resulting in a new fuel pump and fuel filter, that was improperly installed and got that fixed. It has continued with the problems and they are getting worse. I had the fuel pressure checked, came out fine, then had a full engine diagnostic test, all testing fine. The mechanic suspects a sensor. The car acts like it is going to stall, then just when I think it is going to quit, it kicks in and runs great.
I got bad fuel a while back and it is doing the same behavior except does not quit. It happens very intermittently, now in every driving situation, except since I brought it in. The mechanic said if he checks the sensor when it's not happening, it would be a waste of time and money. Is this true? A faulty sensor will not read as faulty? This town is full of bridges, and the highway has long stretches of nothing and a mountain pass. He is suggesting I drive it until it happens again, then take it in, but that's what I did the first time. Do I really have to wait till it quits in one of these driving scenarios?
View 1 Replies
I have 2006 Pontiac Torrent AWD with front disc and rear drum brakes. My ABS & traction control lights come on together (sometime) when I hit brakes slowly to slow down my car around 20-30km/h with a grumbling/scraping feeling sent to my feet from brake pedal (feel like rumble strip on highway). ABS & T/C lights go away if I shut off engine and restart car. It also happens if I accelerate at that speed. This issue does not happen when I hit brake hard.
View 11 Replies
I want to change the spark plugs and wires in my 1996 Ford Escort (1.9 Engine).
The problem is trying to remove the No. 1 spark plug boot and spark plug. Both are located behind the alternator and are difficult to get to. I tried a boot puller but could not get easy access to the boot to pull it off the spark plug. The other three boots and spark plugs are readily accessible.
Is it sufficient to place the dielectric compound just inside the opening of the boot before placing it back on the spark plug, or should it be placed on the metal clip that is ~2-3 inches down inside the boot?
View 2 Replies
I need to change the rear brake pads on a 2007 Expedition and was going to turn the rotors also. It appears the rotor is held onto the axle by a large nut and not having done any brake jobs in several years, I've never run into a rear rotor that's bolted on. Is this the case and if so, what size socket do I need to get it off. Also, I was curious if there is anything else I need to know before I dive in. I heard it was difficult to get off.
View 7 Replies
Ok I reinstalled the new rotors and pads clips and warning tabs. The rotors match the old rotors size , thickness and hub clearance. 2 questions
Vehicle still on stands ....
After tightening everything up on the passenger wheel and the rotor seem to have a lot of play or movement... Normal or not ??
Now drivers side hub and lug nut spindle is not moving , possible another issue ....
Passenger side spins freely ....
if I did not have bad luck I would have no luck at all with this truck
View 8 Replies
I have a 1996 escort wagon with strange auto transmission behavior. Sometimes during the summer months but mostly during the winter; the transmission will start off in 3rd gear from a stop and won't go any higher or lower. If I drive it around for a while, it will suddenly shift into 4th then the transmission will act normally for a while then for no reason will just suddenly start off in 3rd gear from a dead stop. It has been doing this for about 8 months now. 146k miles. I have tried shifting through all the gears manually. It will drop down into first when I put the lever there, but when I move the lever back up into drive, it goes right back into 3rd.
View 1 Replies
Went and got new tires on the supercrew. Went going through parking lots or simply driving i hear a loud squeal like brake pad squeal. I put brand new wagner ceramics on the truck. Also if i turn to the left the driver side rear sounds like brakes are dragging against the rotor. Whats goin on with this. The squeal will happen between 10 mph to 20 mph and the grinding noise will happen if I am cruising or turning to the left. It goes away when i apply the brakes.
View 1 Replies
