Ford - Aerostar :: 1997 Van Will Not Move When Put In Drive Or Reverse And Push Gas Pedal
Feb 26, 2013
I have a 1997 ford aerostar van that i recently acquired through some family,when i got it it was running fine but has recently started having troubles.The Question i have is this i put my car in drive or reverse and push the gas pedal the car doesn't move.....we have tried putting transmission fluid into it and that worked temporarily. What it could be except just a bad transmission?
View 2 Replies
Advertisement
I have a 1998 f150 4x4, the truck has not been driven in a few years and it’s been outside in my driveway up on jack stands. I just rebuilt the front end and did a four wheel break job, after getting the truck off the jack stands, I can't get it to move in drive or reverse. I also noticed that when you go from reverse to park the gears grind and I can't even get it to shift into 4H. I checked the tranny fluid and it is fine, also the tranny was just rebuilt a few years before I stopped driving the truck.
View 6 Replies
1996 Jaguar XJ6 4.0 Litre Base, 43000 miles... While driving, this car, suddenly accelerator pedal becomes very hard to push and car will not move at all even if you press hard pedal to the floor( Requires a lots of force). If I put brakes on, shift the transmission to reverse and to then to drive, it will start moving again. No check engine light comes on and there are no codes stored in computer. This never happens on cruise control. Car starts flawlessly even on cold morning. Battery is new and charging system works fine. Spark plugs were changed at 30,000 miles so also direct ignition coil on cylinder No.3 .....
View 3 Replies
Last night I jumped into my Treg to move it into my garage. When I pushed the brake pedal to move the gear selector out of park, I heard a whooshing sound. Like the sound of a bellows-type foot pump I use to inflate my dinghy. I could also feel a slight amount of movement in the transmission lock button on the top left side of the shifter when doing this.
Now I'm noticing this noise whenever I apply the brakes. It doesn't appear to affect braking performance, but does have me wondering. I'll have the dealer check this out when I take the Treg in for the recent recall (got my notice yesterday).
View 14 Replies
1999 windstar transmission. Daughter drives van,never had any problems and suddenly no drive or reverse.Put it in gear ,no rpm drop, same for reverse.I put it in park and it will not roll so I don't believe its a linkage issue. Its like it has no torque converter. Fluid is at the full mark,and has no burnt smell . Its been my experience that a trans. Usually starts slipping,or no up shift or makes some noises when its getting ready to puke. She stopped for a stop light, went to take off and it just rev-ed up like it was in neutral.
View 3 Replies
I been working on this unit and I running into this
no foward
no reverse
no foward in and gear at all
I have to check pump pressure
I'm changing fluid and filter
1994 F53 460 CID will not move in drive or reverse - iRV2 Forums
View 5 Replies
I have an 03 Escape that is very difficult to start after it rains, if I open the hood and let it dry out for a few days it starts fine, however if I put it in drive or reverse and press the gas it will not move... if I hold the brake while it is in gear and give it gas it does not rev up, however if I put it back in neutral or park it revs up. I normally cover the hood with a tarp to prevent this from happening however I was shutting the tarp in the door and a lot of water got in the floor board of the truck I sucked it all out, that night the radio started playing all on its own, I came out to the truck turned the radio off it stop went back in came back a while later and it was on again, so I pulled the fuse... but there are two buttons that stay lit on the radio the preset button 1 and 2 stay on all the time and I can not figure it out either. This is my beach truck I only use it for that purpose..however it is fall fishing time and I really want to go...
View 4 Replies
My 2002 lincoln ls v8 140k miles doesn't move when put into reverse or drive 5 or even d4,3,2,1 , it just starts to roll back/forward when taken out of park. It has the gear selector with d5, d4,3,2,1 not the select shift. I was told needs new transmission, but before it stopped moving completely it was still driveable second slipped at lower speeds(mostly when looking for parking or in traffic).
I had made an appointment to bring my car to the shop and the same day is when it stopped moving. All this happen within a week during the week i constantly got an e where d5 was and on last day check engine light came on.
View 4 Replies
I have a 2008 GS350. Been having brake clicking when I move from reverse to drive and lately been happening more when driving regularly. Brought it in to Lexus to get the complimentary 19-point inspection and they said I needed new brake pads and rotors. I did do a search and found it can be issues with front spindles, sway bar, bushings.
View 5 Replies
I replaced the front hubs and bearings on my brothers 2002 Camry today. He drove less than a block and developed awful grinding noise and it won't move in reverse or drive. It rolls when I put it in park. I had to pull it back into my shop. Is it possible the inner CV came loose and i didn't realize it? It all seemed to go back together fine. The new CV axle nuts were quite tight and slow to put on with my impact gun.
What else could possible go kaput when I re & re hub/bearings? And what a long ugly job to replace those bearings. Don't even think about doing this without a good hydraulic press. Up to the point of getting knuckle off, it was easy job.
View 10 Replies
I just changed my oil in my mk4 jetta 1.8L and after draining the oil, changing filer, and adding new oil, the car will not move in drive or reverse. Once I give it gas it will move but that's at the higher rpms. I am almost positive I didn't remove the transmission oil but I am just not sure.
View 12 Replies
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 Replies
When I started my car and put it in reverse, it didn't move. It felt like my front, right wheel was in a divet or was being blocked somehow (intuitively it seemed like if I accelerated enough, it would eventually move, but since there was nothing physically stopping it - that I could see - I didn't want to break something by doing that). I tried putting it in drive and neutral and the same issue was still there. I put the car up on a jack and checked one wheel at a time - I could move each wheel completely around in both directions.
I could move the steering wheel all the way to the right and to the left. I tried turning off the 4-wheel drive and that didn't do anything. At this point I'm concerned it could be the transmission or the drive shaft, but I'm not sure what to look for in order to know if I need to get it towed to a shop (hoping I can avoid this) or if there's a simple test I can do, or a way to "reset" something if it may be locked. I haven't had anything happen to the car that would have been of concern.
View 2 Replies
I had a problem with the CV Axle and the Wheel Bearings. I replaced them already and I ran into another issue with the Wheel Studs and the Ball Joint, so I ended up replacing them as well. Yesterday I put everything back together after replacing all the parts mentioned before and I made sure everything was bolted down and tightened, and then the tire back on and lowered the jack. I started up my car expecting it to drive just fine and it was harder to get into gear than before and it wouldn't move in reverse, neutral, or drive. I called a Monroe Muffler around here and they told me that the CV Joint is probably not seated all the way inside the Transfer Case.
So later the same day I took everything back apart and made sure that I put the CV Joint back into the Transfer Case and I put the pin back in and made sure that both CV Axles would turn at the same time, which they did. I figured it was good so I put it all back together again and went through the same process as before, making sure everything was tightened down, all the bolts and nuts and pins were where they needed to be. Everything seemed to be good. I put the tire back on again, lowered the jack, started the car and attempted to drive it again. It still won't move. Why this is happening.
View 1 Replies
I have a buddy that has a 1998 f150 4x4 with 4.6l and 332836 km on it. It will go in to reverse but will not go in to drive at all. Is his transmission shot? Or is there anyway to test it to find out what the problem is.
View 4 Replies
I have a 1997 Nissan Altima that I just barely got and it has started to show signs of trouble.
Sometimes when I put the vehicle into drive and step on the gas the car will not move and instead the engine will rev.I'll put the car back into park and then into drive and it'll work fine.
I checked the ATF, which was incredibly low and refilled it. The engine oil was also very low, which was refilled. The problem still persists. So I decided to add a bottle of Fuel Injector Cleaner to the gas tank.
I took the car for a short drive and nothing happened aside from the fact that the Check Engine light now comes on and off. The car also idles between 1000-1500 rpms.
View 19 Replies
2002 f150 7700 with 5.4 triton and 4r100 tranny started chugging under acceleration and now stalls when put in D, 2 or 1. park and neutral are fine and reverse works perfectly.
Now when I put it in drive it chugs and stalls immediately... 1/10 times it will keep running but chug violently like its running out of gas. will get worse and stall if you press the gas. i can light the tires up for a block in reverse however.
Changed coils 1 2 and 3, IAC, bank 1 knock sensor, camshaft position sensor
View 5 Replies
I got myself a 1997 explorer Australian model when I got it (here's the problem) if you put it in drive it will not engage but if put in first will drive normal then shift into second all good now u have push O.D then shift into drive all good (unless u slow down to almost a stop) ? New problem is, it has gone and lost reverse, put it in reverse and it engages with a small clank (normal) but just slips with any revs. I have read posts here talking about upper and lower valve body gaskets and transgo shiftkit which I have ordered but do there maybe more parts needed? Cause it's going to cost me lot just to put transmission fluid back in.
View 4 Replies
I have a 1997 ford f150 5.4 litre truck and the truck runs real rough kinda surging in park and in drive and reverse i have a couple oxygen sensor codes P 0171, P0174, P0136, P1131, P1151 and an idle air control valve code P1506...
View 5 Replies
I was driving my 1998 Ford F150 the other day and pulled into a driveway. At that time, the transmission quit pulling like I put it in neutral. It shifts from park and goes into reverse but not drive. It has the 4.6L and is 2 wheel drive.
View 4 Replies
I have a 2001 f150 crew cab 4x2 82k miles 4.6 with a 4r70w. Was pulling it over a curb and it popped now it will shift into reverse and load the motor like its pulling against a wall. In drive it will move some but still will lock up and stop moving. I assumed something in the rear had broken from the way it would roll a few feet and lock. Replaced the rear and still have same problem. Is there something I can replace to fix a stuck park or does the transmission need replaced or rebuilt?
View 1 Replies
