Ford :: Ranger 1999 - When Truck Is Idling RPM Will Drop Down Very Low
Nov 21, 2013
I own a 1999 Ford Ranger. About two weeks ago, the engine started acting up. While the truck is idling, the RPM will drop down very low (like .5) and begin to sputter, then shoots up to about 2-2.5 RPM, then back down to .5. Sometimes it will drop so low that I have to give it a little gas to keep it from going dead (which it has a few times).
The motor has around 150k miles I would say (engine was replaced a few years ago, so the odometer shows higher than the engine). My water pump is also going bad, but I am having that replaced this weekend.
Here is a link to a video I did so y'all can hear/see what's going on [URL] .....
View 4 Replies
Advertisement
Ok, I replaced the head gaskets on this truck a couple years back and now I am having symptoms similar to the ones I was having then. I am not entirely convinced that this is what is wrong however.
Symptoms:
Truck was idling rough until it warmed up
Truck takes forever to warm up or simply does not warm up
If/when it warms up it operates at higher than normal temp/almost overheats(it hasn't overheated yet)
Heater blows very cold air
White smoke(has been cold outside so not sure if due to temp or coolant)
Overflow bubbled when I shut the truck off, but it has only happened once so far
I am kind of at a loss, but like I said am suspicious of the head gaskets.
View 8 Replies
1990 Ranger 2.3L 4 cylinder. The truck idles so rough it dies. It runs fine going down the road it just seems to "load up" at idle. I know there are hundreds of things that it could be, I just hate to start throwing parts at it. It is definitely running rich at idle.
It is one of those trucks that we have replaced a lot of parts. The scan tool said something about setting the timing??? Is there a way to set the timing? There is no distributor, and it is the one with 2 coils and 8 plugs.
View 1 Replies
Went from right around 18 to 14-15 last 2 tanks. No codes, drives absolutely normal. I have had my 4x4 lights flashing, but the 4x4 has never worked (suspect its a combination of the transfer case motor and the pulse vacuum hubs). Used to flash like this when I would try the 4x4 switch and would take a while to "get back to where it was happy". Recently I have not messed with the switch or anything else.
View 14 Replies
I just got my new up pipes put on as well as a 38R and pulling a hill hard my truck will hit about 22 psi then drop off slowly I have an electronic boost fooler wich has been on the truck since new pretty much but I don't get a CEL at all is this what I should be getting and I was on the 80hp tune? I ordered new boots and plenum inserts they just haven't got here yet. I know I had a leak before on my old up pipes because they rattled every now and then and I could see exhaust coming out of them when it was cold out but I could hit about the same 22 boost with my old setup. So pretty much nothing changed boost wise except it gets up to boost faster now. I would say it's defueling but I was always told the CEL would come on if that was the case.
View 13 Replies
Its a 1999 f250sd 5.4l auto. Has code p1747. Truck shudders and almost dies when you drop it in gear, put it back in park idles fine. I have read all the post on here about this and checked wires from trans up to pcm look and test good. Tested plug c1048 wires with digital meter to body ground with battery unhooked and got 6.66k ohms on pin 11 circuit 925, 421 ohms pins 1 and 12. Plugged c1048 back to trans checked 925 w/y wire at plug c103 got 9.1 ohms back to trans. Is the epc solenoid bad or is it pcm. I think its epc but want to verify before i take trans apart.
View 3 Replies
I'll try not to post an entire book.. But I bought a 2000 F250 not even 8 months ago, it did have issues before but I changed out the spark plugs and coils and it fixed it's original missing issues.. I also just recently changed the fuel filter but it didn't fix it's new problem.. It drives ok around town but if I get over 35 mph it doesn't run well... If I try to keep a steady foot on the gas but don't get the RPMs over 2000, the RPMs will stay where they're at for just a second then they will drop down and the whole truck starts shaking.. I push more on the gas and it shakes even more and the RPMs don't move at all until I really step on it.. It lacks in power going up hills as well... The dealership i bought it from said the Catalytic Converter was bad but my uncle who is a mechanic says it isn't.. It's the first vehicle I've bought so kinda wanna make it last..
View 11 Replies
Any such system in which they can take the key out of the ignition while leaving the vehicle running? I'd like to be able to do this for security purposes of my brand new 2015 250 if I have to run into a store or something of the like. I don't like the idea of leaving the key in the ignition and locking the doors as anyone could break the window and drive off with the truck.
View 7 Replies
My 1999 ford ranger, when started, shakes and then while i am driving. my check engine light is on and reads a #3 cylinder misfire. I have taken it somewhere to get it checked out and they can't figure out what is wrong with it. this problem only happens 50% of the time. I don't know what to do. Also just got a tune up.
View 14 Replies
1999 Ford F-150 V8 5.4L... The other day I was attempting to fix my 4wd. I discovered that the vacuum tube by the 4wd solenoid had become disconnected. I reconnected it and in an effort to see if my fix was successful, I drove my truck up one of the canyons nearby. I got to an area full of loose rock and popped my truck into 4wd. As soon as I began to drive, the truck started idling very rough and died. I attempted to restart it for the next few minutes unsuccessfully. I got it started once and it continued to idle rough for a few seconds and died. I have not been able to start it since. It turns over but will not crank. It is not throwing any error codes. What I have checked so far:
Spark plugs are working.
When turning the ignition into the ON position, I am able to hear the fuel pump working.
I have not seen any cracks in the vacuum hose.
All the fuses are still okay.
What the culprit may be?
View 2 Replies
I just changed out my IAC. Truck is still idling too high. When I squeeze the host to the IAC it idles down. When I unplug the IAC the truck immediately dies.
Does the IAC talk to the the Throttle position sensor? Should this be my next part to change?
2002 F250 5.4L ....
View 4 Replies
My 1997 f150 5.4 has started an idle issue. The truck when started will idle around1200 rpm and not settle down After driving a bit it will drop down around 800 and idle rough and sounds like it has a plug fouled. As soon as you give it gas it clears up and sounds fine, then drops down an idles rough.
Checked for vacuum leaks but don't see any. pulled the MAP sensor and cleaned it, but did not change.
View 7 Replies
I got a 2000 f250, 5.4l, I got a check engine light bout 2 weeks ago and didn't experience any driving issues. The code was p0171, just recently I've been experience troubles idling, if I let my truck idle for about 3 minutes it will want to shut off, also on acceleration the hole truck bumps, feels like I'm in an earthquake. Where I should start with this problem?
View 11 Replies
I would like to know what's happening, it seems as if idling for a minute to let my transmission temperature dial raise past the lowest line on the dial fixes or at least drastically reduces a couple issues.
The truck will deliver power much smoother off the line. I've been concerned about this for a while. The degree to which it happened wasn't constant but it seems like the truck is having trouble grabbing on (so to say) to the power coming off the line. I sort of liken it to a rope. When I give it the beans the rope goes forward but it takes a half a second or so for the truck to "grab" on to the rope. Never hard shifts, it's just delivering the power off the line or from a near stop.
Idling for a minute seems to fix this, power delivery is smooth off the line. Transmission dipstick was nice and pink but smelled slightly burnt. This is with the engine cold overnight. Didn't have time to do multiple wipes or check in the handbook for the proper methods of checking fluid, I just pulled it out quickly to take a look before heading out. Fluid covered the whole tip.
Second issue that seems to be fixed is that the battery light doesn't come on nearly as much and not for nearly as long. Typically the battery light will come on and off seemingly on its own whim during the drive. However, it seems to stay more consistently off if I idle right after startup.
Now bear in mind I baby my truck, I don't rev it high right after startup. Just low enough to cruise around the parking lot until I hit the road then I accelerate up to 40 - 60 depending on my route. I'd gladly give it the minute to warm up in the future but if I could get down to the bottom of this that'd be preferred, I doubt this is required behavior.
I do realize that these issues are not tied to startup behavior but I find it interesting that idling for a minute at startup to let the transmission gauge rise seems to mitigate these symptoms.
View 1 Replies
I have a 1999 ranger 3.0 4x4 automatic the truck has a delay when put into drive sometimes it slips at take off unless I force it to downshift and stay in first and from second to third gear it shifts very hard at around 3500 rpm would an oil and filter change. I do not have the cash for a new trans and I can't afford a new truck. I love my little ranger...
View 10 Replies
1999 Ranger 4.0. I have an issue with my ranger. Sometimes the truck runs awesome.While driving along the truck will miss and sputter and buck, when this happens, I almost can't maintain my speed. Sometimes when this happens if I put the truck in neutral and shut it off and restart it. The problem will temporarily go away. Occasionally it will go away on its own. When it goes away on its own it's like someone flipped a switch and all power is returned and running smooth. When the truck is at idle it depends on the mood of the truck, sometimes it's fine and other times it wants to die. I got to make this truck last awhile longer.
View 7 Replies
I have a problem with my 1988 740 Turbo. It starts and runs fine, but when cold it experiences a drop every few seconds when idling. In other words, when idling cold, it will act as though the key was turned off but just before stopping completely it catches and continues to run.
I guess I'm trying to describe something other than rough running, or a poor idle - this is more like an ignition short where the engine completely stops (but never does). The tach needle shows this also. It continues doing this while accelerating around the neighborhood but once the car is at operating temp it smooths out. I live in San Diego so it never gets cold here.
The car was tuned up last year and the distributor was replaced at the same time. New cap, wires, plugs. Car has close to 290K and still runs great except for this issue.
View 2 Replies
When your car is idling the rpms drop below 600rpm and you can feel like its going to stall but then goes normal. How do i fix this? Clean throttle body???
Also how hard is it to change the transmission fluid? Possible to do it at home?
View 7 Replies
I've had my 2000 Honda Accord V6 for about 3 years now and have had an idling issue pretty much since I purchased it. After driving for at least 50+ miles, and if its hot out it can easily have this issue as well, and leaving the car be for around 15 to 30 minutes, on start up the car drops RPMs immediately and dies. Multiple tries and it will do the exact same thing. Recently I found out a trick to make it work correctly which is revving the engine to 2000RPM for about 3-4 minutes, slowly dropping it down to 1500 RMP for around the same 3-4 minutes and finally down to 1000 RPM for an additional 3-4 minutes and letting off the gas. Usually after doing this the engine idles fine, car drives great. However, it must be noted that on Summer days with temperatures in the 85+ range, if I'm climbing (going up a hill for a long distance) the car might bog down on me, will not go above 50MPH and I have to pull off the side of the road for 45+ minutes before the car will run correctly again. This has happened about 3 or 4 times in the 3 years I've owned the car.
I would rather not have to rev the engine in hopes this fixes the issue each time so I'm wondering what could be the cause in the first place? I've replaced so many things including spark plugs, ignition coils, battery, idle air control valve, gasket, fuel pump, fuel pump relay and on. I gas the car up with Chevron gasoline, I've dumped in I don't know how many different fuel injector cleaners and have also tried Heet as well as Sea Foam cleaner. I've also had the car checked for vacuum leaks.
I've asked multiple mechanics if this could possibly be a vapor lock issue, but they all turn that idea down. They tell me that since the car is fuel injected this can't be the issue..but, I don't know, could it be the issue?
View 9 Replies
1999 XTL 4.0 auto, was doing fine, replaced Interior light bulb, now wont crank over!!! i suspect the anti theft system... how do i fix or ByPass the security system, i can start the truck by Manually engaging the starter Relay under the hood.
View 1 Replies
Just finished putting a fresh 460 backed by a (1977) c6 in my '68 ranger and now I'm having (what I believe is) transmission problems. The truck will idle and rev properly in gear but as soon as I put it in drive or reverse the RPM's drop and it dies. I jacked the back end up and put it in both drive and reverse and the tire's spin, but if I try and apply the brake to stop them the truck will die. My suspicion is that the torque converter is locked up all the time. I have managed to get it in gear and give it gas and it'll drive and shift fine, until I come to a stop. My question, what would cause the converter to do this? It's the same transmission and converter that I pulled out a month ago and I never had any issues before...
View 4 Replies
