I have a 2002 F250 just replaced the transmission range sensor because I got a po705 code, sure enough one of the leads was broken. Now it won't start in park but halfway between park and reverse and when I put it In park the reverse lights come on.
View 5 RepliesOk had a check engine light. It directed me to replace the IAT sensor.. After some research I found it was integrated into the MAP sensor. Purchased a new sensor and replaced. Drive about 15 miles CEL throws another code. P0106 (sensor i just replaced) faulty Map sensor.
Followed procedure to replace sensor.. unhook battery cable reset ecm. After reset engine is hard to start. Followed by RPM changes (assuming its the ECM re-adjusting). Then CEL flashes 5-6 times and goes out, Drive 15 miles. Map sensor code reappears. (note i only purchased one sensor But repeated install 2 times).
My thought is against wiring. since the codes refer to different signal wires one for IAT one for MAP sensor. Faulty replacement sensor?
2002 Accent 1.6L
truck runs good just has po125 code
View 1 RepliesI recently acquired my dad's old truck. Its a 2002 Explorer EB 4.6L 4x4. Great truck, family owned since new. Recently it has had the service engine soon like pop up and its throwing code P0340. The mysterious cam sensor code.
May I ad that the sensor itself is new, OEM ford. I have just replaced the alternator (which is usually a common problem for this code), and still no luck. The car starts up, still runs great, and has had no hesitation or stalling.
My mechanic friend checked it out and said that it is getting some voltage, but not as much as it should? the wiring to the PCM looked good too. The Ohms on the CMP checked out good too.
I really hope its not the PCM on this car. I may have to just take it into the ford dealer to see if they can diagnose the car. I do work as a tech at a small indy shop, but currently dont have the time since i'm trying to finish my schooling this year.
I just want my car to be in tip-top shape...
Looking for some experience/recommendations for the "what to do" and "in what order" for an error code. Recently the "SERVICE ENGINE SOON" light came on and has stayed on for the last 2 weeks. It has don this before after a heavy rain but went off after a few days but not this time. I took it to Advance Auto who hooked it up to a Trouble Code Reader and got back "PO174- Bank 2 system to lean". From what I've read from the Haynes book and other forum postings this is either a O2 sensor issue or a intake manifold gasket issue? Does this sound right? Next is how to go about addressing this issue in a systematic manner so as not "fix" 10 things that don't need fixing and not running to mechanic and paying a buttload for something I can do myself for less.
View 1 RepliesI'm getting a p0452 fault on my 2002 Escape 3.0 V6 2WD. From what I've read, that seems to indicate low FTP signal below .22v. As I understand it, the FTP sensor has 5 v applied, and the output to the ECU goes down as tank static pressure increases. Conversely, I think the voltage back to the ECU goes up as tank static pressure decreases (for the vacuum leak test measurement).
What the approximate voltage is at atmosphere (engine not running, vent valve open, etc)?
I'm guessing the "less than .22v minimum" signal back to the ECU might look more like either the signal wire shorted to the frame somewhere or the signal wire open (maybe corrosion in the connector)....
Also, where the FTP sensor is located on the Escape and how to access it?
My 02 Explorer (XLT, 4.0) decided to throw a new code today. PO136, O2 Sensor Circuit (Bank 1 Sensor 2).
While it may be a wire issue, I still plan to replace the sensor. So the question is;
Can I get to it from under the vehicle or is there an access panel under the console like on the 2nd gens?
I have the sensor on order and plan to get it done on my days off next week.
The "service engine soon" light is on. I got code 0141 on the code reader. The repair manual for my F150 is stating that the code is for bank 1 sensor 2.I want to check the sensor, but I don't know the location of bank 1 sensor 2. I would like your advice as to the location of the sensor, and what should I check for?
View 9 RepliesMy 2002 Ford Airbag light is flashing 46. I believe this is the Drivers side crash senor. I am repairing the left front fender and left front wheel suspension. I have replaced the two air bags and airbag control module. Where is the left front crash sensor?
View 13 Replies2002 Ford Escape... My OD light started to come on every once in a while, and would go off once I turned the car off... This being said, as far as I could tell, the tranny was running smooth. Then an engine light popped on and this code and explanation come up... P1744 "Torque Converter Clutch System Stuck in OFF position".
I recently came back from a bit of a trip... and after shutting the car off, it didn't want to restart. Since this time, the car has begun to start, but the engine light remains on with the P1744 coming up...
Research seems to indicate that the problem is with the Torque Converter Solenoid. You Tube videos show that there are two solenoids just under the transmission pan...
I have been getting a CEL P0420 for low cat efficiency bank 1 on my 2002 Ford Escape V6. The truck runs fine otherwise. I have ran two loads of Cataclean and the light keeps coming back a few days after CEL reset so I am pretty sure one of cats is done. I am going to replace with an aftermarket cat. My question is, with this code, do I need to replace the front exhaust manifold cat or the rear manifold cat?
View 1 RepliesI have a '02 F350 just over 114k miles, tow light is flashing and just had P1876 code come up. 4h and 4l engage and disengage with out a problem. Code reads 2wd solenoid circuit failure. Where is this solenoid is located?
View 1 RepliesMy truck was running fine the past few days minus a cylinder misfire and a lean code the misfire was due to a coil pack being out no big deal on that part but yesterday on 7/30/13 my temp gauge turned off my truck wouldn't go below 1k rpms and then the over heating light came on. i drove the one mile home and turned it off an hour later i went back out to my truck to get to work and it refused to start.
I decided to just hold my foot down on the gas and crank it and it eventually started drove it to work with the same symptoms. now today its doing the same thing except now the truck is broke down in the parking lot at my job the engine is flooding cause i can smell it last night i changed the thermostat. I can get so that i can get my truck up in running its a 2002 f150 5.4L 4x4....
I have a very Big problem with my Ford Escape 2002 I have this problems code: P0305 accuses Cylinder #5 P0306 accuses Cylinder #6.
I already change the gasket i buy the felpro Kit, and i Also replace all the sparks and spark plug boots, I clean the air sensors and i also replace the EGR, i try to switch cables, and all is the same the car start buy when i accelerate it just go off, i don't know what can i do next, somebody told me to change the fuel injector, i take the pressure in both spark holes the number 4 was 150 and the 5 and 6 was 120, No leaks oil. My car is a Ford Escape 2002, XLT 3.0 4x4
I have a 2002 f150 4.2 code p0340, ran rough, replaced cam sensor. drove after replacing and it runs fine now, code and service engine light comes on after restarting. from what i have read could this be a wiring problem?
View 4 RepliesSo the past few weeks my truck has been sputtering a lot. It seems to do it more so in low RPMS but when I lay on the throttle I didn't really notice it. I haven't had time to look into the issue but yesterday the issue got drastically worse and the CEL finally came on. Registered P0174 as well as a number of other codes including misfires on 7 of the 8 cylinders.
So far I have replaced the fuel filter. Spark plugs are only a few months old. I didnt think it would make sense for all of the coil packs to go out at once so I was thinking either a fuel issue or vacuum leak. Why would it only spit out P0174 (Banks 2) and not show P0171 (Banks 1) along with it? Fuel pump? Vacuum leak? Where should I start? 2002 F150 5.4L...
Looking to see how to repair my blinking light. Code reads a 27, most what I've read says it's a PAD light, which this truck does not have. It has been in an accident, both airbags deployed. Since then both seat belts & bags have been replaced, nothing else.
View 7 RepliesI just started recently getting this code on my '02 F150 with the 5.4. It only started doing this since the temperature started cooling off. The light, next to the oil pressure gauge comes on only at initial start up. Once the motor warms up, it goes off. I'm due for an oil change, which I'm getting today.
View 4 RepliesI have have been getting a p0671 fault code every time I start my truck now that its cold. If I clear it and its warm it doesn't retrigger at least until it sits overnight again. Is this likely to be that the Glow Plug needs replacing on the #1 cylinder? Autolite Glow Plug is only $20 or so. Mechanic is recommending changing the bank and the harness but I'd rather just do the one GP myself if possible. I see on here that the valve cover has to come off. Which side is #1 on and do I need any gaskets etc? How big a job is it to remove the valve cover? I'd go and look myself but its cold out ...
View 1 RepliesMy 4.65L V8 Explorer has an issue in low gear - RPMS rev high but car doesn't shift up.. eventually "catches" with a jerk but the OD Light started flashing and the Systems Screen reads Check Transmission. Light goes out and message goes away after turning car off and restarting. Had one Tech look at it - he said second gear is toast and need full transmission rebuild. Another Ford Tech looked and could just be solenoid needing replacement and advised to have a transmission service (not a flush) done....
View 2 RepliesI have an 2002 7.3 powerstroke. It has a super chips installed, set on heavy tow mode. When throttle is on the foot and I start up a hill check engine light comes on. Code is for icp fault or uncontrollable. Also happens on cruise but more often on the foot. Have to reset to get check engine light off. Light stays off til I go to pull a hill again. I am also pulling a horse trailer with 1-4 horses. Could the programmer be causing this?
View 4 Replies