Engines - Repair :: 2005 Ford Freestyle - Lean Misfire
Jul 16, 2014
I have a 2005 SEL Freestyle with 114K miles. Cyl #3 missing. Has all the symptoms of a "lean misfire" - reading the code said #3. The indy mechanic already replaced the spark plug and the coil. Misfire still a problem. Tried to put some cleaner in there which did not work. He thinks the head needs to be replaced ....
The a/c is also busted. Needs a compressor. Not to mention I'm probably looking at brakes before much longer.
View 5 Replies
Advertisement
i have a 2005 camry 4 cyl. and i have a couple of code: second o2 sensor, system too lean, misfire cyl. 1 2 3 and 4. when i run the car it is incredible how much gas it take.
I first replace the second o2 sensor and i cleaned the maf sensor, air filter, iac and trhotle body but the codes came again.
View 2 Replies
I took our 2005 Ford Freestyle to get an oil change this morning. It is now shaking violently if we drive it more than 60 mph.
View 2 Replies
My freestyle has 239K on it and the it has been infrequently having periods of starting the car and having no drive and then turning it off and every thing is fine when you start again. The other day it stuck in 3rd gear and wouldn't go above 50. We stopped the car and started it and ran fine but the check engine and transmission light came on.
View 3 Replies
93 Mercury Cougar 3.8L V6 with just over 83,000 miles
l've been trying to figure out this issue for ages, but can't seem to find the root of the issue. When driving and accelerating to 40mph, the rpms drop and GET STUCK at exactly 1000rpm. Forcing the accelerator down makes the engine bog and sputter and not go any faster. No check engine lights whatsoever.
The idle is very rough and low in park (700rpm compared to the regular 900) and very low in drive (500 compared to 650-750). When stopped in traffic for a while, it begins to shudder and shake like it wants to stall right there. Now let me run down the extensive list of parts l've thrown at it, bringing only temporary results:
Replaced catalytic converter
Replaced IAC valve
Replaced O2 sensors
Rebuilt transmission (runs great, so l've ruled that out)
Replaced 1fuel injector
Replaced MAF sensor
Replaced motor mounts
Cleaned throttle body extensively
I asked a guy at a Firestone and he said that l needed a valve job. Asked another guy at another place, he said l needed a fuel system cleaning. Asked another guy under a tree, said l needed a new speed sensor. What could be the root issue? l was thinking carbon build up over 22 years maybe? Almost all 83k of those miles have been city miles...
This car is my baby, all l want is for it to be able to handle highway speeds without a hiccup. l'm keeping it and plan to see 100k hit the odometer and many more miles!
View 19 Replies
I have a 2005 Ford Freestyle Limited AWD and there is a loud ticking noise at idle. It seems to quite a little when put in gear.
View 6 Replies
I have a 2005 Ford Freestyle with 59,xxx miles. My wife and I drive it less than 7,000 miles p/year. About six months ago it began to surge (we had already taken it back to the dealer for some work on a recall related to surges while idling). However, the surge that now occurs is not related to the recall--it can happen anytime, even when on the highway while in cruise control at 70 mph. It makes the driveability of the car questionable. We have had it back to the Ford deal repeatedly, only to be told a number of high dollar things that seem to be based on guesses rather than actual data. No codes have come up with computer diagnostics.
We have also taken to independent mechanics, only to be told there is nothing wrong. Only once did a mechanic say that he 'felt' the surging when he test drove the vehicle. But even then, the shop said that they would have to do a tune-up (which raised a red flag with me because tune-ups no longer seem to be the proper term to be used with modern engine maintenance). I did a lot of research and as a result I asked a mechanic to test the fuel pump. The result is that the low pressure was 39.5 lbs, and, the high pressure was also 39.5 lbs.
View 6 Replies
2000 Chevy Monte Carlo 3.4l - The problem that I currently have is that the car will not idle smoothly, it bounces between 600 and 800 rpm. I have replaced the spark plugs, wires, fuel filter and thought I checked the hoses. Just got done changing the upper and lover manifold seals, during which I replaced or cleaned what ever was suggested by the place I purchased my parts through. I am at a loss, I have begun to notice that there are small fluctuations on the highway when I am using the cruise control and am on flat land.
View 16 Replies
I have a 2005 Ford Freestyle 140,000 miles, that has kind of a hiccup miss also there are times when all of the gauges drop and them come back up. I have had the car at the dealership twice and to another mechanic. When I took it to the dealership the first time they told me that it was the spark plugs and the number 1 coil also had a mouse nest in intake manifold. I have replaced the spark plugs, coil 1, clean intake and replaced gasket, replaced MAF, fuel rail sensor and EGR as the codes have been read.
Last time I picked it up from the mechanic it started missing in less than 10 miles to the dealership. The computer said nothing at first then the mechanic took a drive with it. He did have the gauges drop. The codes said charging system. My other mechanic check the battery said it was charging fine and that the alternator and battery cables are all good. Dealership and mechanic are at a loss for what to do.
Last night I was sitting in the car looking for a button that had lost. The car had not been driven all day, off, no key in the ignition. I heard the static noise that I have become familiar with and looked at the cluster and the gauges were all at the below their normal off position shaking and then stopped and returned to normal position. Should I change cables, battery and alternator even when tested they say that they are OK?
View 1 Replies
After my 2005 Nissan Sentra check engine light came on I had the codes read. The code is indicating that there is a lean air/fuel ratio mixture. I'm thinking this may be a false positive(bad sensor), clogged fuel injector, etc. The light has gone off and come back on. I live in Utah where the cold weather may play a factor. How to diagnose the real problem, or where I should start?
View 8 Replies
I am getting cylinder 2 misfire and lean fuel bank 1. change the coil and didnt fix the misfire.
View 2 Replies
2006 f-150 with a 4.6L. Its got 175k on the clock and ran like a sewing machine despite little maintenance other than oil changes. Recently it started running like crap; no power and missing so he borrowed a scanner and it was giving multiple codes. Here's what we have done so far, not necessarily in this order :
1.Checked for vac leaks with carb cleaner (this can be tough as engine runs crappy and hard to detect minor changes in rpms while your under the hood) no leaks detected yet
2. Changed the plugs, all looked good except for one which was heavily fouled and the electrode ate away mostly, I wasnt there and he doesnt remember which one but have a suspicion, more on that in a min
3. Changed most of the COPs and checked them all with a spark tester, all are firing.
4.Cleaned the MAF sensor with MAF cleaner
5. Checked back pressure on the exhaust by removing an upstream o2 sensor and holding a plastic fitting hooked to a pressure gage long enough to get a reading, about 1 lb idling to maybe 2 max when engine is reved, gage is not the best and fluctuates a 1/2 lb or so. Exhaust does not smell of rotten eggs.
6. Changed the fuel filter, it was terrible
7. Ran a bottle of Seafoam in the tank
8. Took the throttle body and egr valve off and checked for carbon stoppage, the holes in the egr were not blocked
9. checked the PVC valve and line and both elbows
7. checked the injector connectors with a noid light for signal, they all flash, checked the injectors them selves with a multimeter set for ohms, all about from 13.5-14.5. This should mean they arent fried but could they still be stopped up? They all sound like they are pumping when you listen with a mechanics stethoscope
9. Changed all 4 o2 sensors as this had never been done anyway
10. Compression check on cylinders, all within 10% of each other at about 180 lbs. When we pulled the plugs they all looked good except for # 7 which was heavily fouled ( I suspect the same on the original plugs) and again with a bad electrode, the part coming out of the porcelin. Intrestingly, this was an autolite plug, the rest were motorcraft, I hoped this was somehow just a bad plug but no change with a new MC plug
11. Changed the injector on #7
The scanner reads lean condition on banks 1 and 2 and random misfires on #4 and # 7 still. Per a troubleshooting tip online, we sprayed some carb cleaner in a small vac line coming off the manifold to induce a rich condition and the scanner showed the o2 sensors go to .900 which is what they are supposed to do per the guide. This means they are functioning correctly and a bonafide lean condition exists. I am leaning towards a vacuum leak around the plastic manifold under the aluminum one, maybe the gaskets but would like to rule out the egr valve, could it be the culprit?
I have even considered the possibility that the PCM is bad, though not likely. I have read to detect a vac leak you can hook the scanner up and spray the carb cleaner around on the manifold and lines with the scanner hooked up watching the scanner PID for the o2 sensors and when they detect the cleaner, they will hit that .800-1.0 meaning the engine sucked the cleaner in and you have found your leak. The exhaust smells rich. If it is a vac leak, you would think it should be a massive leak and not hard to detect, as crappy as the truck runs. I have searched the forums for days and exhausted about all I know to do.
Most important note: early on I suspected low fuel pressure as a possibility; with no schrader valve on the fuel rail and no easy spot to T into the system, we were scratching our heads how were gonna measure psi but the scanner reads absolute fuel rail pressure, gives about 40-43 psi. I hope the scanner is telling us what we need to know there, would prefer a mechanical gauge on the rail!
View 2 Replies
My truck was running fine the past few days minus a cylinder misfire and a lean code the misfire was due to a coil pack being out no big deal on that part but yesterday on 7/30/13 my temp gauge turned off my truck wouldn't go below 1k rpms and then the over heating light came on. i drove the one mile home and turned it off an hour later i went back out to my truck to get to work and it refused to start.
I decided to just hold my foot down on the gas and crank it and it eventually started drove it to work with the same symptoms. now today its doing the same thing except now the truck is broke down in the parking lot at my job the engine is flooding cause i can smell it last night i changed the thermostat. I can get so that i can get my truck up in running its a 2002 f150 5.4L 4x4....
View 1 Replies
1998 ranger 4.0L. I ran my scanner on my truck to day and my 2 bank 1 sensors seem to be bouncing between .150 and .700 but my bank 1 sensor 2 seems to be stuck at 680-720 and not bouncing, is this normal?
I did pull a code po135 heater circuit malfunction BANK 1 SENSOR 1 ...
Also I am not sure where my fuel trims should be...
My
ST1 10.0
LT1 25.0
ST2 12.0
LT2 25.0
closed loop.
When I first got the truck I pulled codes for lean bank 1 and 2 also a cylinder #4 misfire and the bank 1 sensor 1 heater circuit. I reset the codes and the heater circuit bank 1 sensor 1 popped the mil light in 5 min. So I am starting with the o2 sensors. I've not found any vacuum leaks at this point.
View 3 Replies
My Honda's check engine light and VSA light were on. The diagnosis was cylinder 3 misfire, an apparent Honda problem and one that I've had fixed once before on this same car at the dealership where I bought the car. This time the tech said I needed the pistons replaced and that the damaged pistons had also damaged the cylinders so they needed to be repaired (not replaced), and that I needed new spark plugs. My car has been in the dealer repair shop since July 16 (3 weeks today). I've had cars in the shop before and know just a little about cars. Three weeks seems like a LONG time. My question is: Is this normal or not (I am a woman and I'm not sure the tech/dealership is being honest with me. They assure me that this repair can take a long time).
View 17 Replies
Here are the codes I'm getting:
P0455 - large evap leak
P1451 - main control (evap canister)
P0306 - cylinder 6 misfire
P0174 - bank 2 lean
are these all related? Or two separate issues. I have replaced all the evap lines with new lines. I have a new egr valve, and exhaust manifolds, and what should I look at 1st
View 4 Replies
I have a 2002 VW GTI, it's entirely stock and I can't get rid of this lean code. Compression is Good. Injectors are Good, Vacuum Limes are Good, Spark Plugs are Good, Coils are Good!!!!!. I only have two weeks to pass inspection in DE, I'm a college student and as most of us know, that mean $0 for car repair.
View 3 Replies
I have a 2001 Audi A4 1.8t (AWM engine, B5 platform). When I start the car, I get misfires on all cylinders (very rough idle, sometimes it stalls when the engine is cold) and the car appears to be running lean. Once the CEL comes on, it runs fine (albeit the slight loss of power do the ECU going into limp mode to correct the problem).
So far, I've done the following myself: new O2 sensors, new SAI pump, new EGR valve, new diverter valve, new N75 valve, new vacuum hoses, cleaned the throttle body, new MAF sensor, cleaned the air filter, new plugs, and new coils. When the problem persisted, I had my mechanic change the timing belt, check for vacuum leaks, change the valve cover gasket, replace the fuel pump and filter. None of this has solved the problem! This is driving me nuts.
At this point, there are only two possibilities that I can think of:
1) Catalytic converter is clogged? I pulled out the pre-cat O2 sensor, started the car, but it still misfired. This seems to mean that there's another problem (i.e., if the cat is clogged, it's in addition to something else).
2) Dirty fuel injectors? I've put two bottles of Techron through the car to no avail. From the outside, they look pretty dirty, so I'll definitely try removing them, cleaning them, and replacing the gaskets. Hopefully this solves it.
Is there something I'm missing?
View 7 Replies
I am getting the dreaded emission workshop.
The codes i am getting are p0301-p0304 and p0171
Which are misfire on 4 cylinders and system to lean (bank 1).
Here is what I have done:
Got the 4 ignition coils replace, replaced the mass air flow, replaced the air filter, replace the plugs.
I just check the L wire and it doesn't have any cracks or holes
I don't know what to do next.
View 4 Replies
i have a 2005 f150 4x4 5.4 3 valve. it ides good but when it is in on it splutters, and also feels like dead cylinders in passenger gear. i checked the codes the other day and i had a cylinder 5 misfire. so i cleared it and today checked again and had running lean bank one and cylinder 8 misfire, then checked one more time and had cylinder 7 misfire. I am sure it is a bad coil but how do I know which one?
View 2 Replies
05 5.4 F250 4x4. Keep getting those codes. Can't find any vacuum leaks. swapped rear O2 sensors. Fuel filter twice in last 11k miles last time was 1k ago. Will the 430 code cause the lean codes from a bad cat? I've been getting the 430 code for at least 4 mo's.
View 6 Replies
