Dodge - Ram50 :: 2010 - Grinding Noise At 1400 - 1500 RPMs?
Jan 20, 2013
I have a 2010 Dodge RAM Hemi Laredo pickup. Love it. Currently 34k miles. Have kept up with all maintenance. Since about 3k miles, I have intermittently heard a "grinding" noise at about 1400-1500 rpm. Usually while accelerating going up hill/inclines. Assumed it had to do with automatic gear shifting. Have reported this to dealer maintenance folks at each visit. They have reportedly not been able to identify the source, as they claim they do not hear it, despites numerous test drives. Everyone who drives with me has heard it!. I am concerned, as at 36k my full coverage for the transmission warranty expires. Incidentally, at 33,100 miles 2 broken studs were extracted from right exhaust manifold. A new exhaust manifold gasket and 2 new studs were replaced for a different niose. Are these related, or any clue about the "grinding" that I still frequently hear at 1400-1500 rpms?
View 9 Replies
Advertisement
I have a 2008 Mazda3. The car has a replaced engine with 24,000 miles on it. The engine was put in before I bought the car.The car and engine run like a top; except at certain RPMs and when in gear. When I have the car in any gear (auto), the engine makes a rougher noise at RPMs 1400-1700. As I apply more gas, the RPMs seem to get stuck at 1700, then it will break through and run smooth 2000+ RPMs. The engine sounds perfect at all RPMs except 1400-1700 when in gear. When I have it in park and rev the engine, the engine sounds perfect at all RPMs.
View 8 Replies
I have a 1994 dodge ram 2 wheel drive with a 318. Idles fine but when put under a load it starts surging and bucking at about 1500 rpms. Idles at 1500 no problem only under a load...
View 4 Replies
i was driving the ram the other day and about four miles from home after accellerating after stopping at a traffic light the car the truck made an intermittent banging noise boom...... boom...... boom and would not go more than twenty miles an hour even though the accelerator was to the floor. I was finally able to pull over into a parking area after about three miles and as I did so everything returned to normal. I was able to then drive home another mile or so including up a long steep hill without a problem except for one little hesitation that really was nothing. hoping some one has an inexpensive solution for me. The truck has 280000 miles on it.
View 1 Replies
ok so my passenger side headlight wont turn on installed new bulb still wont turn on. I pulled the wiring schematic and on the connector i have a h13 bulb with 3 pins for high and low beams. i have voltage when the low beans are on one wire WHT/TAN 10.9 volts (car off) and WHT/GRY is 10.99 volts (car off) the center connector is the ground, when i check the other side that is full functioning i get WHT/DR BLU 11.8 volts and WHT/ LT GRN 11.0 volts when i have the HIGH BEAMS ON THE RIGHT SIDE wires WHT/TAN IS 10.9 volts and wire WHT/GREY is 11.68 volts AND THE LIGHT IS WORKING
SO MY QUESTIONS ARE'* should i have voltage on the connector of the high beam when the high beams are not on
*what would cause the wht/gry wire to be 10.99 volts when it should be 11.8 volts
* how should i fix this could i run a parallel circuit off of the wiring on the fully functioning driver side headlight
View 6 Replies
So my car started doing some weird things. at idle and only at idle it will go up and down between 1100 and 1500 rpm. No throttle input no clutch input or brake input. I do have a CEL on but when I read the code it gives me 01314 on brake electronics setting. I'm using a vchecker pro. I go into all the engine brake airbag and trans menus and do clear fault codes and this fixes it but id like to know what the actual problem is.
View 1 Replies
I have a 3.3L 2007 Sonata. Within the past month, after first turning it on in the morning, the RPMs shoot up to about 1400 and slowly come down to normal after about 5 minutes. It does this in park and neutral, when I put it into drive it goes down to normal. If I drive it for a mile and put it back into park and neutral, it idles at a normal RPM. If I turn the car off for ten minutes and start it up again, it idles normal at about ~850 RPMs.
After doing a bit of google research, a lot of sites say that this is a normal thing for a cold engine to do. However, the RPMs have never gone that high previously. The check engine light hasn't come on.
View 1 Replies
I have a 2001 Camry LE, 4 cyl, 2.2 liter, automatic transmission, 163Kmiles on it.
I'm hearing what sounds to me rather like a grindy sound at around 1400-1600 RPM. Initially the Camry seemed to do it only after getting into 2nd gear at about 10MPH, but now i see that it is associated with RPM and not the gear so much (the noise is less frequent and less loud in 2nd and 3rd gear- not noticing it ever at above that). I should say that the Camry has been making lots of noises since a new exhaust was put in by a cheap Bosnian shop.
It seems to only make that particular grindy noise when starting from a dead stop, but not if i was already coasting at all. So far as i can tell it seems to only happen about half the time- if I'm accelerating very slowly it doesn't seem to happen much. If i start climbing a hill after a dead stop it seems to come on fairly reliably.
It does not seem to make the noise when passing down through 1600 RPM while slowing down or revving down.
When i started the Camry up today, the noise cropped up well before i got to 8MPH (where it typically shifts into 2nd gear). Which is to say the noise appeared before it even started to shift out of 1st gear.
If i stay in Drive or Reverse and apply the brake so as to not go anywhere, the noise generally starts around 1600RPM. Since the car isn't moving, i think this might rule out the transmission. I hope.
However when in Neutral or Park and i bring the engine up to 1600RPM and beyond, the noise does not appear. So that's perhaps not so good. Of course my car idles a lot better/smoother in N and P than it does in D or R. It's rather rough idling in D and R.
I'm hoping maybe it's a vibration issue- something like harmonic amplification- where something only rattles in a certain frequency range. I pulled up next to a brick wall, kept on the brake, went into D and got up near 1600RPM and the reflected noise does strike me more now as maybe being less a grindy noise and more of a rattly vibration.
The Bosnian shop who fixed up my exhaust were too quick to dismiss the noises i heard after they worked on it. I think maybe something is loose. I hope. (I could feel air leaving the flexpipe's woven area itself but don't know if this is normal.)
Going up hills increases the likelihood of the noise appearing (so i take this to be suggestive that it IS the transmission).
However on a flat road if i hit the gas to quickly get up to 1600RPM before I'm any where near auto shifting out of 1st gear, the noise also usually appears (so i take this to be suggestive that this is not the transmission). I've also gotten the noise to not appear until well into 2nd gear.
The fairly-repeatable noise appearing in the 1600RPM zone regardless of my gear position gives me some hope that the xmission is not the source of the noise. So on balance, i think there's some indication it's the transmission, but there's also evidence that the source is other than the transmission.
The noise does not occur in Neutral or Park while revving up to 1600RPM. But then too, the engine, exhaust and vibrations always seem considerably less in N or P, as opposed to being in Drive (or Reverse). Why my Camry is quieter and more smooth in N and P as opposed to D or R? In the latter two modes, i imagine the transmission is engaged? And that the transmission is unengaged in P and N? And would that make the car louder or vibrate more, at least under certain conditions? Is the engine under less load in P and N?
And are noises at certain RPMs in D or R, but not in P or N indicative of Transmission problems? I notice the shop overfilled the transmission fluid every time i've had it changed.
View 2 Replies
My 2006 Tundra with 45000 miles on it has an engine vibration in neutral between 1400 and 1750 RPMs. It does not feel or sound like a miss fire rather a definite vibration. I have heard this is common with Toyota 4.7 litre engines. What might be some things that could cause it? It has always done it and after 8 years hasn't resulted in any engine failures.....yet.
View 5 Replies
My beloved 1995 Dodge Ram Van has intermittent dash panel electrical issues. The gas gauge an speedometer are intermittent, coupled with lights and radio on off too. It It all started when I had the transition services years ago. It has less than 100k mileage.
View 1 Replies
Year: 1999Make: Chevrolet
Model: Silverado 1500 LS
Issue: Bad Transfer Case
Late model 99 Chevrolet Sliverado 4x4 with push button transfer case. At the end of last winter the transfer case began a grinding-noise when attempting to go from 2H to 4H.
I have a great mechanic who has proven both his skill and honesty to me a few times now. I took the truck in for diagnosis. His hope was that the electronic transfer may be faulty but unfortunately found metal shavings when he went to check the lubricant in the transfer case.
Diagnosis: Bad Transfer Case - Replacement necessary.
Mechanic has recommended a salvaged transfer case from reputable salvage dealer.
I have sourced a rebuilt transfer case with manufacturer warranties from a "major parts chain" for approximately 1/3 more cost.
My debate: The truck (while very late model), has a rebuilt engine that has less than 50k miles on the rebuild. I have expectations that I will continue to drive and maintain this truck for a very long time.
Although I am always aligned with less cost, my first response is that the rebuild from "major parts chain" is warrantied and far less likely to require a replacement in the remaining life of the vehicle.
However I am also uncertain how to evaluate the existing transmission. Presumably it has >100k. Is there a risk in pairing an OEM rebuilt transfer case with a transmission this old?
View 3 Replies
I've got a 2012 GLS manual with about 400 miles that now has a noise that concerns me. At just over 1500 rpms there is a rattling noise that sounds like its coming from the rear and underneath the vehicle. It sounds like metal vibrating. I think it could be the exhaust but I am not sure. It didn't do it on the test drive and it is fairly intermittent.
What it could be and if it might be normal? Should I take it in and get it checked out or would that be a waste of time?
View 13 Replies
I was climbing up a hill on the highway, and I was aware of my issue by the time I hit the top of the hill - my car far into the red zone on the temp gauge.
I pulled over just after i got off, let it cool for a few minutes, check oil and coolant and they seemed fine (from what i could, but it was dark. Drove home because it was only a few mins away, and it had cooled a bit already, but it started sounding really weird at low rpms (1200-1500) almost a clanging noise.
Just as i was pulling into my driveway, there were a whole bunch of weird noises, and at least one of them was me losing coolant from the cap. Turned off the car and the coolant overflow box was completely full, and the radiator cap had leaked some too.
Some other things i noticed - sounded like boiling water inside the large hoses, hoses felt empty, and the coolant box emptied all of a sudden after the hoses sucks everything back up.
View 4 Replies
I have a 2001 v10 with about 157k miles on it. Recently (within last 2 months) I am getting a ticking noise that is pretty constant. It doesn't seem to increase with rpms and I can barely hear it with the hood open- I hear it much better with the hood closed. It seems to start about 2-3 seconds after I start the car (when fan clutch engages?) and seems to be coming from the front middle of the engine. I do not see any broken exhaust studs. I do also occasionally have a ticking noise at 1500 rpms (only at 1500 rpms- not sure if it's related or not). I made a short video- not sure if you can hear the noise.
View 8 Replies
Experience a grinding noise at around 1500-1800 rpm when driving?
The noise sounds like the 2nd gen valve spring start up but not as loud.
The dealer was able to replicate the noise on my car but they don't know what is causing it.
They called the regional guy to come look at it but he doesn't have a clue where or what is causing the noise.
2015 350fpsort
30k miles
Noise starts at around 10K-15k miles and dealer couldn't replicate it then but I hear it everyday.
Update with video : [URL] ....
View 2 Replies
I have a 2003 Camry 2.4 LE with 120k miles on it. It's been very well taken care of. As of now, here is the maintenance that has been completed at my dealership. By the way, I don't trust dealerships, but I do have one nearby that is actually beyond outstanding (and I know a little about cars):
- Regular oil changes, and always with 5W-30
- Radiator flush and thermostat replacement
- Tranny flush
- New front brakes, rear brakes cleaned, and lines flushed.
- Oil pan gasket replaced
- Valve cover gasket replaced
- Spark plugs replaced (at around 105k)
So, with this information being provided, here is my current problem. Lately, as I accelerate between 1500-2500 rpms, the engine has a louder than usual (but not too loud) groaning noise. Basically, the engine just sounds a tad louder than normal along with groaning noise. The engine also feels as though it is running kind of "dry" (if that makes any sense).
Now, above 2500 rpms, it's just fine. It's amazing on the highway, but I feel as though it has slightly lost acceleration in the city. The only issue with the car is the infamous greyish/blue smoke at startup, but that rarely happens and when it does, its a small amount of smoke, and it has never affected it's performance or gas mileage. Another thing is that I had to have that dreaded oil splash guard removed, because apparently the timing chain punctured it and it was about to fall off.
This problem has been recent within the last month. Just before this, the car has been on a roundtrip to Tucson from Tulsa, and Amarillo twice, complete with 32+mpg on the highway! So, what's wrong? Serptentine belt? PCV valve? Cam or something underneath the valve cover?
View 11 Replies
I have a 01 b5.5 Passat. When I'm in tiptronic and I'm about to hit 3000 rpms, a really off noise goes off and it's like a grinding sound.... Like when your car doesn't want to go to the next gear!
View 1 Replies
Codes currently on ecm: P0134, P2125, P1174, P0735 My 2003 Santa Fe 2wd 3.5l with 160,000 miles was driving fine, then all the sudden whenever I reach about 3500 rpms there's a grinding noise that sounds like its coming from near or in the automatic transmission. As for the codes: P0134- I just replaced the o2 sensor with an oem part from autozone, so not sure why that's popping up. The connections look fine. P2125 and P1174- I'm trying to figure out whether the accelerator position sensor or throttle position sensor needs to be replaced. I have a multimeter but don't know if that will be able to tell me which one is out. The P0735 gear 5 incorrect ratio and grinding noise at 3500 rpms is what I am mostly worried about though. Could a transmission flush work with that?
View 2 Replies
I have a 2007 Dodge Caliber manual transmission. When I shift the car (while driving) from 2nd into 3rd/4th/5th gear, I suddenly notice what sounds like a "grinding" noise that stays with the car while in those gears. It's clearly an abnormal noise and noticeable but not obnoxious. It does not occur in 1st or 2nd (although it seems that maybe at higher rpms in 2nd gear I begin to notice it coming, though maybe it's my imagination), but the second I shift to 3rd gear and give it gas, the noise shows up instantly. Now when I let my foot off the gas, the noise goes away 100%. The second I give it gas again, it comes back. Also I don't believe the noise increases or decreases in relation to the speed of the vehicle. It seems to stay constant no matter what speed I'm at, as long as I'm actively giving it gas.
It occurs every time I drive, but I don't notice any other weird noises or problems with the car and the clutch feels good. I haven't been able to find any leaking anywhere underneath the car. It has approx. 92,000 miles and is a 1.8 liter 4-cylinder. I've spoken with a few folks and I've been given the following ideas:
1) bad clutch/assembly (replace clutch kit)
2) bad throwout bearing
3) bad bearing inside transmission associated with 3rd,4th,5th gear rod (?)
4) low transmission oil, 3-5 gears not oiled enough and causing noise
5) maybe nothing to do with transmission at all?
I plan on taking the transmission apart this week with a mechanically-inclined friend of mine and if I have a good idea of what it could be, that may save us a lot of time by not having to take unnecessary things apart (ie. tranny vs bellhousing).
View 4 Replies
I have an issue with the 02 1.8t (wife has an issue). We recently took our car in to get some service work done and the mechanic informed me that he thinks the tranny is starting to go and just baby it....Fast forward a month the wife is driving the car, she said at around 40mph 2k RPM and the RPMs just drop after hearing a screeching/grinding noise....
Then she tried to apply throttle and it redlined...She said it would shoot up in RPM and not go over 30mph, she used the triptonic to get home and was able to get up to 45..Sat for a bit and I drove it, everything seemed ok..Shifts good, stops fine, no weird noises, etc....
Car is a 2002 Jetta 1.8t w/ 148k miles, regularly maintained, never had tranny oil flushed..
View 2 Replies
I have a weird issue with my 2002 4x2 manual Nissan Xterra...when I drive along (usually happens when I'm in 3rd or 4th gear), and depress the clutch pedal to start slowing down for traffic, while the gear lever is still in the 3rd or 4th gear position, the rpms start coming down as the car coasts, but then a strange grinding/whirring/grumbling noise starts happening. The noise immediately goes away if I pull the gear lever into neutral, OR if I re-engage the clutch to start accelerating again. So, it only happens when BOTH the clutch pedal is depressed, AND the gear lever is "in gear". What could this be? The car has about 115K miles, but I believe the previous owner changed the clutch recently (80-90K), and the clutch itself feels fine.
View 3 Replies
