My truck wouldn't start so i replaced the fuel filter and it ran fine for a week than wouldn't start again. Took it to a mech, who ran all the computer codes and scans on it and came up with a lift pump pressure problem. Replaced the pump and it ran for 4 days, now it doesn't start again. They said the injection pump was fine.
View 2 RepliesMy 98 dodge ram 2500 was running and now the gauges don't work and the fuel pump isn't working either, I have checked and replaced fuses and relays with no luck ...
View 3 RepliesI am installing a fuel pressure gauge into my 02 7.3 I went to the thread the sensor into the plug hole on the fuel filter housing and it wasn't threaded, turns out the sensor thread is slightly smaller and a different thread ... The directions say to install it into the filter housing or the lift pump ... So I'm assuming I have to go the lift pump direction of installing it but where the lift pump is or how to install the sensor into it while not throwing a code or causin problems ... A step by step and even pictures.
View 14 RepliesLooking at a 2002 Dodge Diesel 5.9 TURBO 3/4 ton pickup. There is an oil leak on the drivers side that you can see if you look over the tire, that the owner says comes from an overflow out of the oil pan. Never heard of it. Owner says it loses about 1/2 qt. oil at every change at 3,000 miles. Do I need to run real fast??
View 7 RepliesI have a 1994 Black Ford F150 and i was wondering if i could lift the truck 6 inches only using lift blocks (or any other cheap way to get my truck off the ground)....
View 2 RepliesMy dodge truck won't start. I replaced the fuel filter and that cured it for a week then it would't start again.Took it to a mech. and they scaned it with there computer and diagnosed it as a lift pump issue as the pressure was a bit low. Replaced the pump and that worked for 4 days, now it won't start again.
View 1 RepliesI am towing my 5th wheel RV trailer and just started out on my journey. I've driven 350 miles. I stopped for a breather for about two hours. Now my truck won't start and a low oil pressure indicator beeps in the message center. My truck is a 2011 F250 super duty 6.7ltre diesel. Recently had oil change and fuel filter change.....
View 14 RepliesI have a 1998 Chevy K2500 with a 350 engine. 220,000 miles. It starts fine when cold and drives fine. My problem is when I shut the engine off say to get gas or run into a store. When I return to start the truck it will just crank over as if it is not getting gas. If I pump the gas pedal it will fire up after a bit. It will start to stall if I put it into drive but will recover if I continue to pump the throttle. Once I am under way it drives fine until I make another stop. The check engine light is not on.
View 6 RepliesMt truck will suddenly die while going down the road. I know it has a oil sensor and wont start or run with oil is low,but recently it just dies in the middle of the road or won't start after a drive of a few miles. After sitting for a few minutes it will usually start. This was happening a couple of times a day until this week when we have had ice and snow, we have been in four wheel drive for four days and it hasn't died or failed to start even once. Whats up with that ?
View 3 RepliesSo the truck wont start, no crank no nothing all lights work etc. I am getting the icp code. I replaced the icp and the pigtail about a year or so ago what should I be looking at?my icp voltage is .22 volts with the koeoff. While trying to crank it I get no change in voltage. My ipr is at 14.8 and the ficim is at 47. Also when I unplug the sensor it still does nothing...
View 8 RepliesEarlier this week the truck was hard starting every time. Tested the batteries: 12v engine off, 14v engine running, all good.
The next day it threw a P0284 – Cylinder #8 contribution/balance, and was clearly missing on a cylinder. Despite the lack of a puff of smoke at start-up, I was pretty sure it was an injector. So I ordered one from White Bear Lake, and a fuel pressure test adapter from Strictly Diesel. Then I decided to do some testing with AutoEnginuity. Tried the injector buzz test first and got a note that the truck was not capable of performing the test. Tried starting truck and gauges swept and wouldn’t turn over. Tested batteries again: main battery 11volts, aux 12volts.
I got the batteries in and the stupid thing runs like new. Only codes are P1000 and P0603. Truck passed the injector buzz test, and cylinder contribution test graph is almost a flat line.
Take-aways:
1. Bad batteries can cause all sorts of havoc.
2. Always use a voltmeter that displays tenths of a volt, because if it’s only showing whole volts, it could be rounding up. The 12 volts from my first test was probably more like 11.6 volts.
3. Always do as much testing as possible before buying parts.
4. Costco does not sell Kirkland batteries anymore. They only stock Interstate, and the Interstate warranty has dropped from 36 months free replacement to 30 months.
5. The Walmart and Autozone batteries with the five year free replacement are “out of stock” and I’m guessing they won’t be back with Interstate dropping their replacement dates.
6. Most of the car batteries in the US are made by Johnson Controls.
7. Motorcraft batteries did not get very good reviews.
8. Interstate said that AGM (absorbed glass mat) batteries stand-up better to the additional vibration and heat experienced under the hood of a diesel, but they are significantly more expensive, and not all the brands offer an AGM with a better warranty than their best lead-acid offering. Also, the guy at Sears said AGMs are only beneficial for newer cars that continue performing electronic functions after the ignition is turned off. He said he’s seen lead-acid batteries outlast AGMs, but didn’t specify if those were out of diesels or not.
Questions:
1. Can I expect the P0603 to go away after the drive cycle is complete?
2. What should I do with the new injector? If I return it there’s probably a restocking fee. If I wait for a complete injector failure I don’t get the core charge back until then. With the FICM compensation, I don’t know of any way to identify weak injectors without IDS.
So I have been fighting an electrical issue off and on since I bought the Excursion and I am at my wits end!
Put in 2 injectors. 1 in November and 1 last week. Thinking that it would fix my P0603 and the missing issue I was having. Plus the truck tossed a code for #4 and #5 injector. According to a snap on scanner and my AE the injectors were bad. The missing issues are gone, but I keep getting a p0603.
Go back to the middle of May. Truck died and refused to start. I put a fuel pump in it due to lack of fuel at one point thru the no starts. Shop had it 2 weeks and replaced the Cam sensor. Truck has been spot on for the last month zero issues.
Fast forward to today! Hooked up the trailer and loaded my tow tune. Check codes before hand and have a P132b code. Look it up and is a multitude of things to check. Clear code, tune the truck and head out for the weekend. Sat in traffic for 95 minutes to go 13 miles to the highway I needed to get to.
Driving the truck I had zero issues, until I got off the exit ramp to the campground. During the 2 hour drive I monitored a few pids on the scan gauge to see how things were on the truck after the work. The following are driving down the road at 2k RPMS 70 MPH give or take 5 MPH.
boost 7.3
map 22.9
EOT 225
FWT 211
TFT 163
CPM .28
ICV 1.9
VGT 57
IPR 37.3
CVI 4-5 (fluctuates)
SYNCH went to 0 when it died.
Truck shuts off and restarts right away and keeps running. I get to the campground and hook up the tuner to the truck and I have 2 different codes. My buddy the KAM P0603 and a new one Crankshaft sensor Pos A/ I can not remember what the code # was.
So after dropping 1500.00 on the truck the last 2 months, I am at a loss. The shop I took it to was a new place for me and I was not impressed. The lack of communication, 3 scratches on the truck and saying the truck had a miss and they didn't look at the injectors at all.
The 2 options I have are 45 miles away or 100 miles away. After today I believe it is an electrical issue and would rather spend a weekend of my time trying to find it. Where are the known chaffing points on the 03' 6.0L.
I just bought a 98 Dodge Ram 1500 4x4. Of course it didn't do this when we test drove it, but as soon as we put the money down the problem started. When you start the truck, the interior lights start blinking. I thought it was a door ajar warning, but after testing the doors, it doesn't stop blinking.
Sometimes it will stop when you put it in gear, sometimes it starts again. some times it stops for a few seconds and then starts again. So far it has always stopped blinking after we have driven for a little while. It seems like it will sometimes stop when I fiddle with the 4 wheel drive shifter.
So I just replaced the low pressure fuel pump on my 14 6.7 and it seems to be running as good as it was before. I need to get an aftermarket fuel filter setup for my truck. So what are you using, why did you pick that particular system and is it working, does it really work for taking out water and other contaminates? These fuel systems don't seem to be up to par in filtering modern day fuel, I need peace of mind.
View 14 RepliesI have 2008 LS460 done 30,000 miles since last few days. I have CEL and when i hooked it to a reader the code came out P1235 "High pressure fuel pump out of range" any one had this problem before!
View 3 RepliesI am a new diesel owner. I bought a 2014 F250 about 9 months ago. Three times in the last 50k miles I have heard the fuel pump near the tank making noise. Twice, while making the high pitched noise I have gotten a low fuel pressure warning and reduced engine power.
The first time, I left the truck with the dealer for two days while a tech drove it around. everything checked out fine. (30k miles)
The second time I heard the noise i did not get the low fuel pressure warning. (40k miles)
Today, I heard the noise and got the lower fuel pressure warning just before the truck stalled out. Lucky for me, I was near home. After a minute the truck start and I nursed it the last mile or two. (56k miles)
The tow truck just picked it up and is off to the dealer. It sound to me like the low pressure transfer pump is bad or going bad.
I have a 1993 Grand Caravan 3.3L V6. When I leave the van set for a couple a of days (or even overnight) and then start it, I have no oil pressure for a minute or so. After the engine has been running for about a minute or so the oil pressure finally comes up but not to normal. Once the engine has warmed up the oil pressure returns to what could be considered "normal". After the cold start, no oil pressure problem, the engine and the oil pressure is fine for the rest of the day. Let it even set overnight though and I have a repeat no oil pressure with start up.
I am thinking that there is a problem with the pick up tube not sealing properly and allowing the oil to bleed down while the engine is off for an extended period of time. So, in effect, I have to basically prime the oil pump at each start up. I haven't noticed any leaks of engine oil anywhere, so I am thinking that this is an internal problem. Is there a check valve or O-Ring associated with the pick up tube or oil pump that may cause this problem? Is it a fairly easy problem to correct? On this engine the oil pump is located in the front of the engine block behind the timing chain cover. (As best as I could determine from the Haynes Manual).
This pump hangs down fairly low and appears easy for ice and rocks to hit on my 2013. Something hit mine and took a chunk out of the drain tube. No leaks yet but I am looking to get a new one and keep this as a spare, or just JB weld it. Can I just buy the lower section, or do I need to get entire pump?
Any creative protection bracket made? Would just have to take it off to change filter though. Any leak in this housing is a major show stopper when in the middle of nowhere! Maybe why it is getting brought into the tank on new models?
I was driving to a job this morning with my truck loaded with tile for a job and it just died.
It has power to the lights, radio, etc. But when I try to start it it does not even crank and it has no fuel pressure on the gauge and the pump is no running.
It is as if the truck has no power. When it died is was like I turned the key off and it just stopped.
1996 Dodge Grand Caravan, 3.3 L engine. When the outside temp is a good range (50 degrees F & above) there is no problem starting. But when it gets below 40 deg. F and really chilly outside temp, I still have strong battery power, but when I switch on the ignition, I don't hear the normal fuel pump activation swirl sound and does not crank - simply silent click. Then I can wait when the outside temp improves and cranks up no problem.
View 6 RepliesMy 2000 dodge ram 1500 Laramie Won't start, Here's what happened. The truck started just fine the day before, No problem. But when i went to start it today it continuously cranked and when releasing the key It shook as if it tried to start and started to smoke a bit from the engine. I popped the hood and looked around, Seeing smoke coming from the engine, there was also smoke Inside the air cleaner box. What this could be, And how to fix it? This is a big problem as I'm moving in two days!!
View 19 Replies