Dodge - Grandcaravan :: 2009 - ABS / ESP / TCS And Brake Lights Are On
Jul 25, 2014
I have a '09 Dodge caravan. The ABS, ESP, TCS, and Brake lights are on. As we drive along the brakes apply, probably on only wheel. After we stop, we can drive on for a short way and it happens again. A mechanic told us that the steering sensor was telling the computer that the steering wheel was turned all the way to the left. I wonder if I pulled the fuse for the ABS pump and ABS valve if it would be safe to drive, at least until we can get it to the dealer for repair. I am cheap and like to get by as cheaply as I can/. I am not fond of ABS, or TCS any way?
View 19 Replies
Advertisement
One tech wanted to replace both rotors and sanding down the pads to re-use (he said my brake pads can last up to one year). The guy in auto part said the surface of brake pads having hard spots could cause the pulsation, replace the pads. Of course, replace both rotors and pads is recommended but I have tight budget! What options do I have? can I just machine the rotors?
View 12 Replies
1996 Grand Caravan with ABS, 3.3L V6, 152k.
Am I correct that Dot 4 brake fluid is equivalent to Dot 3 - with the added advantage of higher boiling point? Is there any downside to using Dot 4, other than a small additional cost? Seems like the cost difference is irrelevant compared to the safety margin to reduce the chance of boiling the brake fluid on a long downhill in hot weather, or - as in a recent puzzler - heating from the exhaust system. Or is Dot 3 really just fine for most cars?
Either way, I'm going to flush the system with new fluid (and replace old parts as needed), it's definitely due. Neither my owners manual, nor the factory service manual, gives a capacity for the entire system. Ditto the Napa store. I'm guessing it's in the range of two quarts. I don't want to buy a full gallon only to let it sit in the garage, but if I need three quarts, I may as well buy the gallon. Where to find the capacity, or have a ballpark approximation for what the system will need?
Also, is there any benefit to flushing the system BEFORE replacing wheel cylinders to keep old fluid out of new parts? That makes sense to me, even if it uses extra fluid. So:
1: Dot 3 vs Dot 4
2: capacity
3: which comes first: flush or new parts
View 6 Replies
I have a 2002 Grand Caravan, when foot is on brake, speedometer jumps all over, engine bucks so bad I have to put it in neutral or park at every red light. When I go forward, it jumps a little, and sometimes will not shift, engine revs up so bad, I have to pull over, shut engine off, turn it on and then it shifts. Speed sensors were supposedly replaced with the plug for them. It is at a dealership, they checked all the sensors, electrical wires, etc, and not it doesn't shift at all!! It is still there, now I have no van to drive. They claim they did nothing to it, it was shifting 90% of the time. It will not shift at all, even when I shut it off and re-start it. Now they claim it may need a new used tranny.
View 1 Replies
I just completed a front brake job on a 2007 Dodge Grand Caravan, installing new rotors and pads. Right front rotor and pad installation went perfectly. Left front - I heard a faint "hiss" as I compressed the caliper piston using a c clamp. In addition, as I placed the new inner pad against the caliper/piston, I noticed that the piston had become slightly "uncompressed," meaning it moved back out a little bit on its own. I compressed it again with a c clamp and had to rush to get the caliper back in place with the new pads in place before the piston SLOWLY worked itself back out and I wouldn't be able to fit the caliper around the new rotors and pads. I completed the brake job, pumped the brakes, and took it for a ride - all seems fine. The pedal is not spongy and it does not travel all the way to the floor.
Do I have anything to worry about? This is my 6th brake job in total. This is my first brake job on this vehicle. The slight hiss and the fact that the caliper piston did not stay seated after I compressed it bothers me.
View 18 Replies
Short Version. 2000 Dodge Grand Caravan, I two weeks ago I replaced the front brakes (rotors, calipers, and pads both sides) I drove the van 100 miles Saturday night with no problems. Sunday afternoon, whilst driving home from a restaurant with 5 people in the van (driving super gingerly because they were my inlaws) the right front brake stuck on and smoked on the drive home. The calipers are new, and I have not had any other problems since I replaced the brakes that were trashed when I got it.
Long version, So heres the deal, I am the proud owner of a 2000 Dodge Grand Caravan, its got about 140,000 miles on it, its a little rusty, but I got it for free. A family member was getting rid of it, as it was 11 years old, and they wanted something newer, and it needed brakes and a few other things. They were going to donate it, but it sat all winter waiting for the donation company to pick it up. Being a consummate grease monkey elite shade tree mechanic tinkerer type, and being in the new family, new house cash flow situation, I swooped in and towed it home in hopes that I could make a decent enough ride that I could fit two adults, a car seat and a dog into.
Now when I got the van I knew it had some problems. That's the reason it was free. But it is/was all fixable stuff. Typical of age and mileage It had a whiny power steering pump, it needed an oil change, the power steering lines leaked, the transmission cooler lines needed to be replaced. It needed a serpentine belt. It has a motor mount that needs replacing. The front suspension clunked because of worn out swaybar bushings and end link Its a bunch of work and few weekends and a few hundred in parts, but when the van was free, and you do the work yourself it costs a lot less.
The front brakes were completely trashed when I got the van, that is one of the reasons that the previous owner had parked it. And it was obvious that the right front caliper had seized, I could not push the piston back in. And that was the one that seized on, and had the most damages so I replaced it, along with the left front, as it was also the original one, and well they were both the same age, and have the stuff to bleed the brakes out. So what causes disk brake calipers to randomly stick on when they are used gently? Because when I drive it angry, such as now, they seem fine.
View 5 Replies
The left side light bulb on the overhead reading light console is burned out. How do I remove the lens or open the cover to replace this bulb?
View 3 Replies
I have a 2004 Grand Caravan 3.8 engine. For the last 2 months the oil light has been coming on when car is first started. If I stop engine and start again the light will be off. I don't think its actual oil pressure because the car runs fine with light on or off. I'm thinking a bad pressure sensor?
View 17 Replies
Sometimes when I start my 2006 Dodge Grand Caravan, 3.3 liter engine, the oil light comes on and stays on, even if I rev engine up. Engine sounds normal, does not sound like oil pressure is low. If I turn engine off and the immediately back on, light goes out and stays out. I replaced the oil pressure sending unit - didn't work. I hooked up a gauge - engine has 60 psi oil pressure at idle - plenty! I'm guessing an electrical problem in the circuit.
View 4 Replies
I have a 2005 Grand Caravan, this winter has been a cold one. The GC has always started without problem but after I back out of my parking spot, it sits outside, I put it into Drive and it will not move and after I give it a little gas it would still not move. None of the gears seem to work, but if I wait a little bit and the Van warms a little more it will go into gear and all is good. This does not happen all the time and when it does go into gear and I drive I do not have anymore problems until the next time it will "act up" on me again. Is this a problem or is it a cold problem and not a transmission problem?
View 7 Replies
My 2000 Dodge Grand caravan loses its gauges every so often. engine light comes on as well as ABS...
View 2 Replies
I got a great deal on this van, and I love it, with one exception. On hot days (73 degrees and hotter) the van will not start if it has been parked in the sun; until the temperature returns down to around 61 degrees (usually overnight, but I have waited it out in the parking lot at work a few times).
When this happens, the lights and radio work fine; the starter motor will not engage. No click, no chugga-chugga vroom-vroom. Sad Curto.
Note: October through about May in North Carolina, this car is fine.
I have replaced the steering column (after replacing the clock spring); I have replaced the Power Distribution Center.
When the problem first surfaced two years ago, I had a mechanic install a wire directly from the starter motor relay to the solenoid. That was an expensive lesson. I'm not sure what the lesson is, so it was REALLY expensive.
So, I thought maybe the Auto Shutdown Relay. Nope... pull that out, and the starter still turns, so that is not my problem. Now I am starting to thing Powertrain Control Module, or something else that could have a temperature-sensitive component.
View 10 Replies
I have a 2004 Dodge Grand Caravan with 120,000 miles. Starting at about 45mph the car has a really bad shimmy when accelerating. The shimmy fades starting at about 55 mph. There is no shimmy when not accelerating. Gently applying the breaks has no effect on the shimmy. I've put on new tires, Change the steering rack and struts and the engine and tranny mounts. what could be causing this?
View 2 Replies
I have a 1993 Grand Caravan 3.3L V6. When I leave the van set for a couple a of days (or even overnight) and then start it, I have no oil pressure for a minute or so. After the engine has been running for about a minute or so the oil pressure finally comes up but not to normal. Once the engine has warmed up the oil pressure returns to what could be considered "normal". After the cold start, no oil pressure problem, the engine and the oil pressure is fine for the rest of the day. Let it even set overnight though and I have a repeat no oil pressure with start up.
I am thinking that there is a problem with the pick up tube not sealing properly and allowing the oil to bleed down while the engine is off for an extended period of time. So, in effect, I have to basically prime the oil pump at each start up. I haven't noticed any leaks of engine oil anywhere, so I am thinking that this is an internal problem. Is there a check valve or O-Ring associated with the pick up tube or oil pump that may cause this problem? Is it a fairly easy problem to correct? On this engine the oil pump is located in the front of the engine block behind the timing chain cover. (As best as I could determine from the Haynes Manual).
View 13 Replies
Lifters are rattling. They have been replaced and are still rattling.
View 17 Replies
I have a 1998 Grand Caravan 3.8L engine with 157K on it. A month ago changed the EGR valve and replaced the transmission oil. Two days ago, went for shopping, parked the van. Came back and did not start (no crank, nothing). Called AAA, checked for battery, which was good. Radio, wiper, lights work. Had to tow to the shop. The mechanic checked for all possible problems. Said everything (Fuse, battery, starter motor, alternator) is good. He is clueless. Told him to check the ignition switch (may be worn out). He says it doesn't seem so.
View 19 Replies
The 96 Caravan I bought a year ago came equipped with an aftermarket dent in the oil pan. It's a bent up generally flat, not all at one point, but there's no leak and no other apparent problem, though of course it does reduce the oil capacity. When I had some overdue warranty work done at a dealer, the service writer told me the dent is exactly where the the oil pickup is, which mostly sounded like the dealer looking for some extra work. I decided I'd replace the pan myself when I had enough miles on the car to see if it was worth the effort.
The pan has a lower sump area that measures roughly 5" x 7" and that entire portion is pushed up somewhat evenly. I'd estimate the deepest part of the deformation is almost an inch, so less than 35 cubic inches lost capacity. 35 cu in = .606 quart.
I can buy a new oil pan w/ gasket at Rock Auto for a shade over fifty bucks to add to an order I otherwise need to place with them. A used pan at the local junkyard would cost ten or twenty bucks plus my labor plus the gasket, which I judge as not enough cheaper to be worth my time and inconvenience (they want me to capture the used oil and take it with me). So it's either buy the new oil pan, or fix something else. Or pull the pan, bend it back to shape, and replace the gasket? It appears to me that the pan gasket may be seeping, though not enough to drip, so it's probably due for a gasket anyway.
Should I care about this, or learn to love the dent?
View 16 Replies
I know if you smell antifreeze when you turn on the heater that is a bad thing. I don't have this issue, but when I walk into the garage after my wife turns off the van I get a whiff of what smells like antifreeze. There isn't a leak that I can find and nothing on the floor the garage out the normal.
2006 Dodge Grand Caravan 80K miles
View 7 Replies
Our van shuts off while driving. This means I have no power to brakes or steering. The only warning light that comes on is the traction control light. Therefore when hooked up to diagnostics there is no information. We have had it to 3 different places with no results or answers. We did have the ignition switch recall performed. We have filed claims with Chrysler with no answers other than arbitration and with the NHTSA.
View 4 Replies
We have been having an issue with our gas tank not filling up continuously for over three years. It automatically trips the gas shut of switch every couple of seconds so it can take a while to fill up. Then every once in a while it fills up totally normally.
View 1 Replies
I have an appointment next week at the dealer to have this checked out. My 2015 Grand Caravan with just over 30,000 miles, has been leaking a bit. Enough to make a mark on any spot I park in for longer than an hour or so. I placed a white poster board under the front end to see if I could identify where and what it may be. After about 6 hours, I checked and it seemed to have several drops of what certainly looked like engine oil. A dark golden. The leak seems to be located about 3 or 4 inches inside the front driver's side tire.This has been going on for just under a month. I keep checking fluid levels, and the engine oil doesn't seem to be diminishing at all, though it is a bit tough to tell exactly because it is clean and hard to see on the dipstick for this auto novice.
An attempt to crawl under didn't produce any real info, seems there is a bit of the oil anywhere in the area when dabbed with a white rag.Again I am a novice, so I am just asking what I should expect when the van is checked out. The car has had all needed maintenance at the correct intervals, though the last couple changes have admittedly been at a quickie place.My father, a former mechanic till retirement told me in theory there is no way to be leaking oil and not have at least some lowering of the oil level, obviously.Could this just be seeping so slowly to not notice a level difference? I know it is next to impossible to get a diagnosis here without a real inspection, but based on the location of the drips and the color of the liquid, any guesses would be great.I am 6,000 miles away from the end of the warranty, and we have a long road trip planned in a few weeks.
View 5 Replies
