I have a 89 dodge dakota and it starts sometimes and other times it don't start at all. When it does start and runs for a few min it will randomly die and when I try to start it after it dies it wont start back up. Me and my dad just fixed the starter relay yesterday and it started every time after that, now today it wont start. New coil, fuel pump, and fuel filter are new.
View 5 RepliesI have a 02 Dodge Dakota 4.7 liter that is killing me. No codes and no check engine light. From a cold start it starts fine but then runs rough. If I let it run for a few minutes, turn it off and try to restart it, it is very hard to start. Also, if I have it running and rev the engine above 3k rpm and let go of the gas it dies. It will idle without holding the gas pedal down but will die after a rev. Fuel pressure and volume are right in spec. Have good compression, spark and injector pulse on all cylinders. I thought maybe a crank or cam position sensor, but either of those would usually throw some type of code. I thought IAC but it seems to be functioning properly.
View 3 RepliesMy 2002 Dakota with a 3.9 (200,000 miles)has a problem that I cannot seem to cure.When I start the engine it never hesitates....it starts without a problem. No excess cranking...it fires up as it always did.It does run a bit rough as if ONE cylinder is missing every few revolutions. If I let it idle in the driveway for five minutes it will clear up and run fine. But if I take off right away the following will happen.I put it in gear (automatic) and for the first mile or two it runs as though the plug wires (More than one) are wet and arcing. I can barely get above 25mph. it will spit and sputter for that first mile or two.
Then suddenly it will clear up and surge....probably because I have loaded the system with excess fuel......and after it clears up , I have no other problems with it weather I'm on a long trip or a short one. If I stop for more than 15minutes, I have to go thru all this again.I've had vehicles that acted like this after a hard rain because the plug wires were old and arcing...that's why I use that as a description.I also noticed that the other day right at the end of a big downpour it took at least 5 miles to clear up.
Before this rainstorm I had replaced the plugs, wires, rotor and cap, while inside the shop so everything should have been bone dry except for all the humidity from the storm. After starting I checked for any arcing while in the dark shop and even moved a few wires that were touching and no arcing was seen from the cap, wires or coil. I also changed out all those parts 6 months ago when I did a major tune up, but it ran fine untill about two months ago.
When this started two months ago is was just a rare occurrence and my mechanic thought that I had gotten some gas with water in it. He had me run a few bottles of injector cleaner it the next few fill-ups and I've run a few bottles of heet through it also. In the last two weeks it has been doing this every time I start up. When this did start showing up it would show a code of a random misfire and the engine light would come on even though I felt no signs of a misfire myself. The light would stay on for a day or two then go back off. A few days later it was back on.I thought that I fixed the problem because the light stayed off for a month.
So it has been only the last two weeks that it bucks and kicks so bad at a startup, but you would think that an engine misfire would show up and the engine light come on. By the way the light does work. Now, I never get a engine light on, and he found no codes in the history. I have my own scanner, but his can do so much more. I never find any codes also. My mechanic ran some diagnostic's and found an up-stream 0,2 sensor bad so we replaced that.
Yesterday I dropped the tank, pulled the pump and cleaned the tank real good. The only filter is the sock on the pump and that was clean. I refilled with fresh gas and I still have the same problem. So I think that we can eliminate water in the fuel, plugs, wires, rotor, and cap. My next thought is the cam sensor in the distributor.
When cold the trans works fine for about 15 mins, then its like you put it in nuetral. No forward no reverse. A friend suggested changing filter/fluids so I did. Worked great for about 4 hrs then same thing. Leave it sit for a few hours and it works good for about 15 mins then nothing. Should I try another filter or something else?
View 1 RepliesSo I own a 96 Dodge Dakota and its had a few problems since I first bought it, but its all fixed except for one really puzzling problem. My head light will flash on and off while on low beams after about 30 minutes (if on high beams its almost instantaneous). It all started out with my dash lights going out then the head lights would go out when driving. I checked the switch and plug, both were fried, so easy enough fix. That fixed the dash lights, but the head lights still go out. I replaced the bulbs and yet the problem still exists. I then took it to O'Reilleys and the put a volt meter to my negative battery post and to and auxiliary wire just 6 inches from the post. When the lights were on they produced around 46 ohms of resistance and when they shut off they produced 26 ohms. Which isnt good, so I replaced the negative battery cable to try and fix the problem. This still did not solve it. The only other suggestion I have been given is to replace the high/low beam switch on the steering whee. Could that solve the problem?
View 9 RepliesI have a 2005 dodge Dakota when I'm driving the steering wheel will shake randomly.This isn't happening constantly when driving and it will stop after I make a turn. In addition it will happen randomly regardless of what speed I'm driving. What's going on?
View 1 RepliesThe truck had a hard time starting, turn the key over hear that it wants to, but won't. Once getting it started, truck would drive fine, but after about 10 minutes just dies while driving. It then took 6-7 tries to get it started again, drove back like no issue. What it could be? I have come up with, potential battery, fuel pump/filter, spark plugs, EEC relay, PCM, or AIS motor, O2 sensor....
View 2 RepliesI have a 1995 Dodge neon 2.0 SOHC. It stars, runs for a few minutes, then dies. Then when I try again it will run for a few seconds before it dies. After that I do not hear my fuel pump engage when I turn they key. It takes about a day before it repeats this process.
View 2 RepliesMy dad has a 2001 Dodge Dakota extended cab with a 3.9L v6 (standard transmission). It will start and run for a while and it will die, if you turn the key it will start up again but will eventually die. He has changed the spark plugs & wires, the distributor cap & rotor, the MAP sensor, and the throttle valve sensor. It still does the same thing.
View 1 RepliesSo, my oil light comes on after startup like usual then shuts off. Anywhere from 2-5 minutes of the vehicle running light comes back on and does not shut off unless I restart the vehicle. Have changed oil pressure switch and oil pressure is reading in the normal range..
05 dakota with 175000 kilometres
I have a 2002 Dakota 5.9l r/t. Always started and ran fine. It sat most of the winter approx 2 months. Now will not start but cranks/turns. Has new battery, newer full tune up and tried starting fluid.
View 2 RepliesEvery time it rains and I forget and leave the truck outside instead of inside the garage, it will not start. It is a 2001 Dodge Dakota pickup truck. It tries to start but will not fire. I have to sit around and wait for a few dry days and full sun - which is hard to find around here other than August and September. I have had it towed to several different mechanics for review. They have all done the same thing - can't find anything wrong so they leave it sit around the lot for two or three weeks until the sun shines then charge me a hundred bucks or so for their diagnostic time and a jump start. Every once in a while out of shear frustration, I have it towed to a new mechanic or one of the previous ones but still get the same results. Does fine in the winter with snow, but it has even done it on occasion when going through a car wash - which I know longer do as I am too old to be pushing a pickup out of a car wash.
View 3 Repliesi have a 96 slt v8 dakota im trying to fix myself. it wont start. put new batt. new starter motor. it just clicks engine wont turn everything in truck is working but when i turn the key to start its just clicks and my radio losses power. so i took out radio and still wont start...
View 2 RepliesI've got a '93 Dakota that wouldn't start this morning after a cold snap, it used to fit just fine in any temp. It's cranking strong, can smell gas, and it's getting spark (used an inline tester). Battery had a full charge. Lay night the windchill got down to -40 Fahrenheit.
View 4 RepliesThis is an ongoing problem that has lasted for several weeks now -- I’m completely flummoxed and at a loss. It goes something like this:
My truck (2000 Dodge Dakota, 2.5L, 5-speed) has developed -- for lack of a better term -- a high-pitched whining squeal, which only occurs after I put it in gear and actually start moving (if I leave it idling in neutral, when starting it after letting it sit overnight, the sound usually does not appear at all). After about three or four minutes of driving time, the sound will show up, but there’s an odd twist: the sound is most apparent, and really loud, when the truck is at idle, such as when at a stop sign or traffic signal; when I put it in gear and take off, the noise will drop in pitch and, depending on how hard I’m pressing on the accelerator, it sometimes disappears altogether.
When I take off, every time I shift gears the sound returns -- only for as long as I step on the clutch and back off the gas, and when I step on the accelerator again the noise falls in pitch and vanishes. It does this off-and-on thing through all the gears, and after reaching the desired road speed (and I’ve reduced pressure on the gas pedal) the sound returns and is constant. Also, if I shut the truck off and wait just a few minutes, and then fire it back up, the sound will be gone, but will return after a short while, exactly as related above. It’s worth noting that, during all this irritating misadventure, the engine has run exactly as it always has -- there’s been no discernible impact on performance.
Now, some considerations. The noise is louder and more strident when the ambient temperature is lower, such as in the morning. Later in the day, when the temperature rises, the sound becomes erratic and somewhat unpredictable, and is much lower in volume, and it will even stop abruptly and then reappear later.
Many people have suggested that it could be the belt or a pulley, maybe. I replaced both tensioners and even installed a new, shorter belt to bypass the A/C compressor (to eliminate it as the possible culprit), but the noise remains. I was skeptical of all that because -- and please correct me if I’m wrong -- a shot pulley making such a horrible racket should get louder as engine speed increases, not drop in pitch and disappear. In fact, the noise seems to have no relation to engine RPM; if anything, it seems tied somehow to intake manifold pressure (the sound vanishes when the truck is accelerating, which is when intake manifold pressure goes down, or so is my understanding), or throttle position, or something else entirely. The vacuum system? The noise seems mechanical to me, not like escaping air (or, well, vacuum) . . . but what do I know?
I have a 93 Camry that quit on the highway. No spark, crack in condensor replaced distributer. Still not run. Rotor not turning, replaced timing belt, main engine fuse heating up replaced that. Now it starts right up but only runs 10 minutes. Then won't restart until several hours go by then it will start again. Runs like a champ when it starts.
View 1 RepliesI have a 2002 Excursion 7.3 4x4 and when it will start is runs for about 20 min then turns off. When I go to start the truck again the theft light flashes rapidly and the glow plug light never turns off. I have tried reprogramming the key to the PATS by leaving it turned for 30 minute then turning it back then starting and that worked for a few times but it doesn't anymore. Additionally I used to be able to take the terminals off the batteries for 20 minutes or so and then it would start after re connecting them but now I have to leave the batteries off for like 24 hours then it will start fine 1 time run for 20 minutes and die and won't start all over again.
I have a snap on solus pro I am borrowing to figure it out but am not very familiar with it, I can only find codes P1876 T-Case 2wd Solenoid circuit (but mine is 4x4) and U1262 data fault for J1850 there is nothing pulling up under the PATS option in the scanner so I don't know whats wrong or where to even begin, it just shuts off.. The truck runs great till it shuts off, buzz test in the scanner doesn't do anything and neither does the glow plug test. When the truck dies is just turns off like someone turned the key off, no running rough or anything first, I am pretty sure the computer is shutting off the injectors and then locking me out.
It is a 1991 C1500 2wd, ext cab, short bed 5.7L engine with about 300k miles on it that I have had for a year. Supposedly a different 350 engine and transmission was put in a couple years ago.
This problem has been going on for 2 weeks. I'll start the car up and it runs just fine, no problems. After driving for about 20 minutes, the engine will die while driving, and will not start back up until the next day. I have sat in the car for literally 4 hours patiently waiting for it to start. I'll turn the key and the engine will rotate, but will not start. When someone shows up to give me a jump after the battery gets low, it will not start. I'll go home and go to sleep, and sometime the next day I'll go to my truck, and it will start back up, and I'll drive back home, and I'll make it as long as it takes less than 20 minutes.
It is not just a "morning problem", but a "first time I have started the truck that day" kind of problem. Last week, it happened to me in the mornings. On Saturday, I didn't leave my house until 2pm and the problem happened. Today, I first drove it at 8pm, and the problem happened.
Things I have changed so far (mostly from Autozone):
Starter - burnt it out when it first died 2 weeks ago, now I know not to crank when below 9 volts - lifetime warranty
Spark plugs - no more engine popping or driving with 2 feet - changed last week on Tuesday - AC Delco CR43TS gapped at .035
plug wires - changed all in November, since I noticed one of the old ones was tore - lifetime warranty
Distributor cap and rotor - changed last month when the engine started popping - autozone
Ignition control module- I changed today, I really thought that would fix the problem after speaking with the Autozone guy - lifetime warranty
Ignition Coil - changed last month because of popping
Fuel Filter - changed last Thursday, thinking it was a fuel problem
Here are some of the other symptoms I have been noticing over the last couple months:
Pretty bad gas mileage, I know it is a V8, but it is just as thirsty when I am not carrying anything as when I am pulling a car. A couple months ago, after driving for about 30 minutes or so, the engine would make a "Pfft" noise and would start popping and I would have to drive with 2 feet to keep the engine running.
About 2 weeks ago my 1997 Buick Park Ave (115,000 miles) began running bad during a heavy rain storm. It was running fine. Then all of a sudden at a stop light the motor hesitated and wanted to stall. I nursed the gas peddle and limped home and turned the car off. The car hesitated and sputtered all the way home as if I was running out of gas.The next day the car would not start. It turned over but would not start. I tried starting the car for three days. My mechanic friend later diagnosed the car and stated the computer was not functioning correctly. He replaced the computer. The new computer seemed to correct the problem.
The car ran great for the next 2 weeks. Yesterday, it was raining hard while I drove the car about 150 miles without any problem. Then suddenly again the motor started running badly. Again, the motor wanted to stall and hesitate as if I was running out of gas. I limped home again. This morning I tried to start the car without any luck. In addition to installing a new computer, In the last 2 months I have changed all the fuel injectors and installed new spark plugs.I have also changed the fuel pump and repaired the fuel tank. My mechanic say the cam sensor and crank sensor are operating correctly. There is spark coming from the coil packs and to the spark plugs. I do not want to randomly change parts.
1993 Dodge Ram 2500 .... Multiple symptoms... some times engine turns over but truck will not start. sometimes engine dies whether driving at slow or high speeds. Happens whether engine is cold or warm. After sitting a while, the truck starts and will run for several days. Has 40 lbs of fuel pressure, we've changed out the ignition switch, crank sensor, distributor cap, rotor, pickup, engine control module, crank shaft position sensor.This has been happening for three months, I've been towed in 4 times. When mechanic connects diagnostic tool to the ecm, the engine starts and runs fine. Diagnostic shows no data of previous problem.
View 3 RepliesLast weekend, the car wouldn't start after sitting for a few hours. After about 20 minutes it finally started. It has started and ran fine up until today. Same thing, it was parked for a while and wouldn't start. Then it did start, ran horribly, then died when it was put into gear. Then it started and ran just fine, my friend moved the car, parked it and turned it off and of course it wouldn't start after that.
I've done a lot of work to this car myself, including entire tune up, fuel filter, cam AND crank sensors (notorious problems on these cars), ignition switch, oxygen sensors, several other things in the past year or so. My only hunch is that it might be the auto shut down relay, but I'm not with the car so I can't test that. We had fuel pressure at the test port the first time this happened, so I wasn't really thinking it could be a fuel pump issue, but with over 210,000 miles anything is possible. Also, it sometimes dies when the car comes to a stop with the A/C on...but this doesn't happen very often.