Dodge - Dakota :: Engine Rev At 4500 - 5000 Rpm But Will Not Shift Until Slightly Release Gas Pedal
Mar 25, 2012
My 2003 Dodge Dakota Quad Cab 3.9v6 auto trans does not shift properly. I have to lift my foot off the accelerator for it to shift. If I don't it just screams at a high RPM and sounds as if it is about to blow. It has a hard time making it up a small incline such as an overpass. Truck will not shift properly when going upgrade. Engine will rev at 4500-5000 rpm but will not shift until I slightly release the gas pedal. Truck will also perform multiple hard up shifts when in cruise control going upgrade.
Took the truck to the dealer reprogrammed the computer with a "flash update" that was no dice. The technician is now saying the original shifting problem is normal because dodge reprogrammed the transmission to avoid multiple up & down shifting when going up a grade. This was down to put "less stress" on the transmission. Doesn't make sense, dodge is saving the transmission by making it work less and destroying the engine by letting it rev at 5000 rpm. Automatic transmission will not shift to third gear unless the gas pedal is almost fully released. Transmission will not downshift to pass.
View 6 Replies
Advertisement
My 2003 Dodge Dakota does not shift properly sometimes going into second gear and it only happens in second gear. I have to lift my foot off the accelerator for it to shift into third. If I don't it just screams at a high RPM and sounds as if it is about to blow. It has a hard time making it up a small incline such as an off ramp. Truck will not shift properly when going up grade. Engine will rev at 4500-5000 rpm but will not shift until I slightly release the gas pedal. Truck will also perform multiple hard up shifts whether in cruise control or not in cruise control, going upgrade. Took the truck to the dealer reprogrammed the computer with a "flash update" that was no luck. Not once has the ENGINE LIGHT ever come on.
So a lot of the comments that were presented to me I have done. Here is a list:
Changed govner senors and solenoid. Did not work.
Checked for exhaust leaks and other leaks. No leaks.
Checked all vaccuums. No problems there.
Had engine checked and dyno tested. No problems there.
Had transmission rebuilt. Same problem. (dealer did work)
Had new transmission put in. Same problem. (dealer did work)
Also, sometimes when I put the truck in reverse, it seems to about to stall, but it doesn't. It also does it sometimes when I put the truck in drive it seems that it wants to stall.
I just recently learned that my truck has a Transmission computer module, Transfer case computer module and of course the main computer. Is there a way to test those modules out?
View 3 Replies
This morning my 2006 Dodge Dakota v8 auto decided to become a large paperweight. I started it up fine and let it warm up a bit (about five-ten minutes), then shifted into reverse to leave my driveway and it won't move. It just rev's and rev's like it's in neutral. I tried Reverse, Drive, and both low gears, but no luck.
Since it got very cold, it has been making a buzzing/whirring sound that seems to be coming from the belts. But that sounds would go away when the car warmed up. I thought I needed a new power steering belt (and still may), but that wouldn't keep the car from moving at all, right?
View 19 Replies
My brake pedal goes almost to the floor when I'm braking.I replaced the rotors, pads, shoes, power booster and the master cylinder 3 times.Had it bled twice and I still have a soft pedal, but now it firms up a bit as I pump the brakes.
View 7 Replies
99 Grand Marquis. Transmission won't down shift unless you release the gas pedal. Check engine light not on, no OBD codes. Changed the transmission fluid and filter. Fluid level OK.
View 3 Replies
I had a front brake job done on a 2002 Dodge Dakota pickup at 85000 miles. When I stepped on the brake, I felt pulsation in the pedal and a sort of wobbly feeling in the steering wheel. Also the brakes were making noises while driving. Classical sign of a warped rotor?! Long story short brand new rotors, brake pads and calipers, later the pulsation is mostly gone but the braking is still not smooth at one point while the tires are turning. Now i do have to older tires on the front but i just bought two brand new tires for the rear. Would it be wise to put the new tires on front to see if there might be some unevenness caused by the old tires before i take it back to the shop?
Also the feeling of the brakes catching on one point seems non existent or so minimal I can not be sure if the road surface interfering while driving slow of applying the brakes gently. But slowing down from higher speeds (above 40 mph) and using more then gentle braking ( not standing on the pedal with both feet) it is definitely there. Before the brake job braking caused the steering turning right. (sign of more braking action on the right - right?). Now with new stuff still pulls to the right but not as strongly. Should not this disappear with the brake job? Or get the new tires on front and see what gives?
View 9 Replies
I have a '96 2.2L Cavalier with an automatic transmission. The car has about 275,XXX miles on it. Recently, I have been having problems with the transmission. Basically, the transmission doesn't shift unless I release the gas pedal and press down on it again. It always happens around the 20-25 m.p.h. mark. If I don't release the gas, my speed doesn't increase much, i.e. it goes up to about 30 m.p.h. and I hear the engine revving hard. Once I do the gas pedal thing though, it accelerates well.
View 1 Replies
1999 Dodge Dakota
3.6 liter w/air conditioning
I'm pretty sure I made a mess of things. My Serpentine belt was all cracked and making noises while idling and driving. It was time to replace it. It's a long story, but my auto mechanic told me to drive my truck for a week and then give him a call. Well.... I didn't do that. My battery went dead and I charged it up and it lasted a month. Yesterday, it wouldn't start so I bought a Serpentine belt and installed it. As far as I know, I didn't damage anything while I was working on it.
The battery was still dead and I charged it, however, the key was turned on while I was charging it. I don't know how I did that, but I did.
The problem I'm having is that the engine is now idling at 2000 RPM. I scanned it and there are no codes or pending codes.
Today, I went out and drew a diagram of how the belt is routed and it's the same as the diagram under the hood. I had a friend take a look at it and he agrees that I put it on correctly.
View 7 Replies
On empty a week ago, filled 1/2 a tank, drove home no issue. Didn't drive truck for a week. Turned it on this morning (didn't warm it up) about 10 minutes into the drive anytime you tried to accelerate, the truck would buck. If you were idling or just had your foot slightly on the pedal driving at the same speed it was fine, it only bucked when I really pushed on the pedal to accelerate. The check engine light started flashing as well.
View 3 Replies
'97 dodge dakota engine starts and vehicle will move and then engine dies. Just bought it and it ran fine. Coil was replaced by previous owner four months ago. At times it will run fine but is not reliable and wife will not drive in it. Had it towed to dodge dealer and they said it needed a new coil which they installed and still have the same problem and now think it might be the ecm which is mine even if it does not cure problem. Truck has 145k miles and otherwise is in good shape. When it does run, engine is strong, automatic shifts good and all accessories work. But, it won't keep running.
View 14 Replies
Cold start. engine starts but wont idle, just dies. rpms drop. Restart same. Must neutral drop to get going keep rpms up until engines shifts then things are fine until next cold start. Cleaned throttle, changed air filter, dry gas, injector cleaner, no warning signal, scans clean. 180k miles.
View 6 Replies
My 2005 Dodge Dokota 4.7L V8 152,000 miles has an intermittent check engine light (CEL) code P0420 ('catalylst efficiency') that turns itself off.
1) 151,000 CEL on, code P0420, checked, cleared at dealer.
2) 151,948 CEL on, code P0420, checked, cleared at dealer (Cat Conv).
3) 152,200 CEL on, code P0420, checked, cleared at local auto parts store.
4) 152,597 CEL on. No checks.
5) 152,815 CEL turned off on its own
6) 152,849 CEL on. No checks.
7) 153,137 CEL turned off on its own.
Twice in this time CEL has came on soon after a fill up from near empty.
Engine runs fine, 18-19 mpg highway.
Have seen numerous on-line reports of other possible causes:
a) base engine problems (coolant or oil) -- coolant temp sensor
b) Air inleakage -- air systems or manifold
c) Lazy front O2 sensor
d) fuel pumps
e) timing or misfire
f) what else? - (gas cap, other...)
What to check first or categories to eliminate?
View 4 Replies
I just replaced fuel pump and tps on my 1989 Dodge Dakota 4 cyl truck. Now it idles rough and the check engine light came on. I have removed battery cable to reset computer but did no good. What could be the problem now? I have since replaced the plug wires and distrib cap and it is flashing 3 5 5 twice now?
View 10 Replies
I have weird kick back when I release gas pedal. Why?
View 2 Replies
Car is a 2000 Corolla CE.
When going at the desired speed (say 40mph) and there is lots of coasting room, I just let go off the accelerator and the car basically coasts. The engine RPM drops from 1600-1800 down to 900-1000 and it actually can coast a long way. Sometimes, I need to go faster (if I'm initially started at a slower speed) and when I press the gas pedal slightly, the tachometer shows the engine rpm jumps from the coasting 900-1000 to 1600-1800.
Is the tachometer (add on by ScanGuage) reporting it correctly? Is this a bad form of acceleration for the engine?
View 8 Replies
My 2011 elantra started making a sound when I turn all the way to the right and slightly again once you release the wheel. It pretty much sounds like a rusty coil being stretched to it's limit. It happens while driving and turning right as well as when the car is not in motion and turning the wheel all the way to the right. Not sure what it could be.
View 21 Replies
97 Dodge Dakota Sport V8. Has spark, turns over, won't fire.
View 1 Replies
My dad has a 2001 Dodge Dakota extended cab with a 3.9L v6 (standard transmission). It will start and run for a while and it will die, if you turn the key it will start up again but will eventually die. He has changed the spark plugs & wires, the distributor cap & rotor, the MAP sensor, and the throttle valve sensor. It still does the same thing.
View 1 Replies
So, my oil light comes on after startup like usual then shuts off. Anywhere from 2-5 minutes of the vehicle running light comes back on and does not shut off unless I restart the vehicle. Have changed oil pressure switch and oil pressure is reading in the normal range..
05 dakota with 175000 kilometres
View 19 Replies
I have had this truck in 3 different shops and none of them could figure it out. The codes say misfire in cyl 2 and 5 bank 1 too lean and primary and secondary circuits malfunctioning for ignition coil. I've replaced the ign coil cap, plugs,plug wires, rotor, pcv, fuel pump, pick up coil, cat, o2 sensors and all sensors under the hood. Switched out all vacuum lines, cleaned the IAC and checked the pulse ring. The truck loses all power and either dies or backfires and regains power randomly. If I drive at night, it will stall and keep cranking when trying to restart. Usually have to let it sit for ten minutes for it to turn back over. Last night it backfired and stalled every 50 ft for over a mile. During the day, it revs up and down at idle by about 100 rpms.
View 6 Replies
Have a 2002 Dodge Dakota automatic. This winter when temps. dropped into lows 10s and zero degree weather, the Dodge truck would start,but would not come out of park gear. Have replaced interlock solenoid and brake light switch. Still have same problem when Temperature drops into low 10s &below. Otherwise,everything ok. (not using ER brake).
View 5 Replies
