Dodge - Dakota :: 1996 SLT Will Not Idle After Restarted When Warm
Feb 16, 2013
We have a 1996 Dodge Dakota SLT that we purchased used. It starts and runs beautifully when the engine is cold; however, if you turn the vehicle off it is difficult to get it restarted and to keep it idling without keeping your foot on the accelerator. The funky thing is that after your "fight" with it a few minutes (i.e., foot constantly on the accelerator), the truck will then start to run correctly and idle correctly until the next time you turn off the engine. We have noticed that on each occasion when we have had this problem, the engine smells EXTREMELY flooded. We've been told its a temperature sensor, any other number of sensors, and now the IAC. If starting by process of elimination with least expensive fix first, what the heck do we replace first?
View 4 Replies
Advertisement
After I drive my truck and park it for any period of time and then restart the truck it will sputter and backfire rpms do not go over 1500-2000. If I put it in neutral and rev the engine this will work but not always correct the issue. Eventually if I just push through it after 2 or 3 min it will go back to normal. I replaced the spark plugs, wiring and distributor cap. I have also changed the O2 sensors nothing seems to work though.
View 6 Replies
I have had this truck in 3 different shops and none of them could figure it out. The codes say misfire in cyl 2 and 5 bank 1 too lean and primary and secondary circuits malfunctioning for ignition coil. I've replaced the ign coil cap, plugs,plug wires, rotor, pcv, fuel pump, pick up coil, cat, o2 sensors and all sensors under the hood. Switched out all vacuum lines, cleaned the IAC and checked the pulse ring. The truck loses all power and either dies or backfires and regains power randomly. If I drive at night, it will stall and keep cranking when trying to restart. Usually have to let it sit for ten minutes for it to turn back over. Last night it backfired and stalled every 50 ft for over a mile. During the day, it revs up and down at idle by about 100 rpms.
View 6 Replies
So my 96 Dodge Dakota's instrument lights went out a couple days ago, I thought it was just a fuse, so naturally I check all the fuses. Come to find out they're all fine, I replaced a few to see if maybe it was just an old fuse. Still nothing. Then last night I noticed that the instrument lights came on between off and on for the lights. So I assume its a wiring problem. Then as I drove down the road I hit a bump and all the lights went off then kicked back on. Needless to say I can't drive around with lights that won't stay on. Where should I check for the cause of this problem?
View 2 Replies
so my 96 dodge dakota has been acting up a lot lately. I can barely drive in town let alone on the highway. when I drive, keep in mind its random most of the time, my truck will start jumping and then lose power. when I try to power thru it my truck will backfire and then shut off. once I try to start again it floods the engine. most of the time it will do this going up a hill or when it has to get above 3000 rpm. I don't know what's causing it. I replaced the throttle body fuel injection sensor and tranny filter but I figure its a fuel problem.
View 9 Replies
My '96 Dakota SLT 6-cylinder pickup backfired and blew a hole in my muffler ... I've had it in three different shops on six occasions since and the thing still hiccups, backfires, stalls ... most of the electrical switches and sensors have been replaced ... right before it back fires, it feels like it is going to stall, then "POW" ... sometimes it continues to run fine for a little while after that ... then it happens again ... When it stalls it feels like it is running out of gas ... it is almost impossible to restart right away, but if I wait a few minutes, the starts right up ...
View 1 Replies
i have a 96 slt v8 dakota im trying to fix myself. it wont start. put new batt. new starter motor. it just clicks engine wont turn everything in truck is working but when i turn the key to start its just clicks and my radio losses power. so i took out radio and still wont start...
View 2 Replies
So I own a 96 Dodge Dakota and its had a few problems since I first bought it, but its all fixed except for one really puzzling problem. My head light will flash on and off while on low beams after about 30 minutes (if on high beams its almost instantaneous). It all started out with my dash lights going out then the head lights would go out when driving. I checked the switch and plug, both were fried, so easy enough fix. That fixed the dash lights, but the head lights still go out. I replaced the bulbs and yet the problem still exists. I then took it to O'Reilleys and the put a volt meter to my negative battery post and to and auxiliary wire just 6 inches from the post. When the lights were on they produced around 46 ohms of resistance and when they shut off they produced 26 ohms. Which isnt good, so I replaced the negative battery cable to try and fix the problem. This still did not solve it. The only other suggestion I have been given is to replace the high/low beam switch on the steering whee. Could that solve the problem?
View 9 Replies
I have a code scanner which indicated that I should change the MAP sensor. I did that, and just for fun changed the idle air control valve and throttle position sensor. Now the idle is extremely smooth in park or neutral, but once I'm in a moving gear it's up to the same shenanigans, antics and tomfoolery I described in my original post: 96 Dakota SLT idles rough & stalls. So I have a 96 Dodge Dakota SLT 3.9 4WD. Anyway, it idles relatively smoothly at about 700 RPM in drive or neutral, but if I'm in a moving gear and need to stop, the idle is extremely rough. Usually, the RPM's will drop to near 0 within about 20 seconds of coming to a stop. It will typically recover and continue with rough idling and near stalling a few times, but within a minute or two it stalls. A few additional details: it starts right up again after falling, it doesn't make any difference if I start it cold and drive immediately or drive it for an hour before coming to a stop, the same thing happens. Anything that looked suspicious to me has been changed (drivebelt, spark plugs & wires, distributor cap & rotor, pcv valve, idle air control valve, and, of course, the air freshener).
View 1 Replies
So I have a 96 Dodge Dakota SLT 3.9 4WD. Anyway, it idles relatively smoothly at about 700 RPM in drive or neutral, but if I'm in a moving gear and need to stop, the idle is extremely rough. Usually, the RPM's will drop to near 0 within about 20 seconds of coming to a stop. It will typically recover and continue with rough idling and near stalling a few times, but within a minute or two it stalls. A few additional details: it starts right up again after falling, it doesn't make any difference if I start it cold and drive immediately or drive it for an hour before coming to a stop, the same thing happens. Anything that looked suspicious to me has been changed (drive belt, spark plugs & wires, distributor cap & rotor, pcv valve, idle air control valve, and, of course, the air freshener).
View 1 Replies
vehicle 1997 dakota engine 3.9L w/autotrans.
The vehicle exhibits an intermittent high idle. I have replaced the usual IAC stepper motor and checked the tps for proper function, also completely cleaned, inspected and relubed the throttle body and linkage.
According to my Inova 3140, there are no codes and the temperature sensors and tps percentage are reading correctly. Also the battery and charging system are functioning correctly.
I do not have bi directional capability or the ability to monitor any of the pid'sOne other thing is that she also has a slight rough idle, but that could be the 200,000 miles.
View 6 Replies
I have a '99 Dakota 4 cylinder. Starts fine but as it warms up or if you gas it the idle stays high. The more you run it the higher it goes. Have replaced MAP senser, throttle position and air bypass with no effect.( map and high tps voltage only codes shown ) Vacuum problem?
View 3 Replies
Here's what is going on with my 2000 Dakota V6 3.9L V6:
After sitting for at least a couple of hours, the truck will crank but not start. After 3-5 tries, the truck does start but idles roughly at a very low RPM for 10 seconds or so and then stalls. I turn the key one more time and it starts up great and idles and drives normally. This behavior is very consistent. I have only driven it about 5 miles after it started doing this, because on that trip, the engine stalled while I was driving. Occasionally the MIL comes on and gives P0443 as the code. Question is, can the evap purge solenoid cause this behavior if it is going bad? I have inspected the vacuum lines, and they seem ok.
One more note: When this first started, I was pretty sure it was the fuel pump. Replacing that has not fixed the problem, and the fuel pump relay is good.
View 1 Replies
Cold start. engine starts but wont idle, just dies. rpms drop. Restart same. Must neutral drop to get going keep rpms up until engines shifts then things are fine until next cold start. Cleaned throttle, changed air filter, dry gas, injector cleaner, no warning signal, scans clean. 180k miles.
View 6 Replies
I have a 2000 Dakota 5.9 truck that has all of a sudden started to idle rough, loses power over 3000rpm or any kind of reasonable acceleration , with a big sucking sound from the throttle body ( no leaks), seems like it is not getting fuel. Someone mentioned it maybe the "MAP" sensor.
View 2 Replies
I just replaced fuel pump and tps on my 1989 Dodge Dakota 4 cyl truck. Now it idles rough and the check engine light came on. I have removed battery cable to reset computer but did no good. What could be the problem now? I have since replaced the plug wires and distrib cap and it is flashing 3 5 5 twice now?
View 10 Replies
I have a 96 E-350 7.3 PSD. I noticed that the A/C seems to work well on the Highway but not so well stopped Idling. I thought maybe it was airflow so I replaced the Fan Clutch... Seemed like it was better for while (could have been my imagination)... I decided to evac the system and refill. The system takes 4 lbs of freon. The van was indeed low so I thought I had found my problem, but it didn't seem to work after evacing and refilling.
With gauges on the system the low side pressure when it was 80 degrees out this morning was 70 and the high side was 145. A/c temp from the vents was about 70.. If I raised the RPM's to about 2k, the low side would drop to around 30-35 the high side would stay about the same... and the AC in the Cabin was in the 50's...
Does this problem have to do with air flow over the condenser, or is possible that the compressor is getting tired. (The compressor stays on the entire time) Could it be a clogged orifice?
View 14 Replies
I have a 05 dodge magnum v6 2.7. Only when its warm it stalls at idle. Scanned it code p0137 came back low voltage o2 sensor 1 of 2. I replaced all 4 o2 sensors and still stalling...
View 18 Replies
96 dodge intrepid, 3.5. Few yrs back kid flooded it at -10f. I changed wet plugs and it started. Ran ok for 10miN, idled fine .n than I drove it 10 miles and it would not idle. I was 150mi from home and kept going. Car ran so-so. Seemed sluggish at 60mph. Exhaust actually made black/soot stain on bumper. My mileage on hwy was about 1/2 normal. I pulled plugs when I got home and they were black. Took about 1 week of driving to eventually settle down. Never did find any reason for issue. Some said my o2 sensors were buggy. I never changed them and had car for 2 more yrs and it ran great. Why it would not idle?
View 4 Replies
I have a 1997 dodge ram 1500 4x4 with the 318ci engine. 140,000 miles. Fall 2009 I replaced the CAT (old one had broken loose and was rattling around inside) and both o2 sensors. A few months later, when I'd start the truck cold it would idle fine then as it warmed at idle it would run rough almost quit then idle up and run fine all by itself. When started warm it would idle fine then hesitate while acclerating a few times then run fine. No check engine light. Now, about 10 months later check engine light is on (P0138 o2 circuit high voltage bank 1 sensor 2). I have put about 5,000 miles on the new CAT. I checked the wires and connections for damage and found none. Also, new cap,rotor,plugs and wires.
View 3 Replies
I had a strange issue today when I left work and started my car. I got in, put my foot on the brake and pushed the ignition button like normal. The lights all came on for a moment and then everything just went out. The brake felt stuck and no electronics would work and the engine did not start. I couldn't get anything to work, I thought my battery was dead, however when I got out of the car (key in my pocket as usual) the car came back to life. I got in and started and it worked fine.
View 7 Replies
