I have a '79 D100 that needs a new distributor. I've removed the two necessary bolts that I know of. I've tried to twist it, and will will barely turn. I've tried to pry it up. I've loosened a few bolts in the area to see if that relieved pressure. I've degreased the area and sprayed WD40 at the base of it and still nothing.
View 3 RepliesMy Dodge 150 truck starts missing at about 45 mph. It seems to only do this after it has warmed up for about 20 minutes.
View 1 RepliesI have a 1984 dodge d150 ramcharger i just bought and it has all sorts of problems I am trying to fix as part of a learning process for me. One problem is it squeals when i first start it when i get on the gas. The faster the rpms the louder the squeal...
View 3 RepliesHaving trouble with my truck not charging. Changed out alternator, v/r and battery and still will not charge.
View 19 RepliesPurchased a new-to-us 1st gen dodge pickup, a 92 D150 v6. It's used once or twice a week at max and only has around 90k miles on it.
So a few months after we bought the truck, it stalled, or more like choked, out while driving on these country, hilly roads, at around 50 mph.. it happened once and we didn't think much of it. It happened again not too long after that, though, and we discovered we could push through the stall/choke by giving it a lot of gas.. it sounds terrible, and shakes and sputters, but eventually catches back and starts to run normal.
As months passed, the problem happened more often. So we changed the spark plugs and wires recently. No difference. In a given 40 minute trip along 45-55 mph country roads, the truck will choke and sputter at least 5 or 6 times. It's now so bad that sometimes giving it gas isn't enough to fix the issue and we have to pull over.
We've got an appt scheduled with a mechanic, Our friends think maybe it has to do with the choke plate or carburetor. It seems to happen more often if the AC is on, and other than this, the truck runs great. It starts up fast and idles fine.
I have a 63 dodge pickup with a habit of burning out ignition coils within 2 weeks. It's happened with the slant 6 motor, it's happened with the 318 v8 and its also happened with the current motor a 440. I have changed the ballast resistor, and the ignition switch, as well as the starter solenoid, and all related wiring.
View 4 RepliesI bought a dodge d150 a month ago. when i bought it, the lights work fine. one night i pulled out the headlight switch to turn the lights on, and the headlights came on, but no parking/running lights came on, and the back lighting didn't come on. if i sit there and jiggle the switch between off and where the original "notch" for the parking lights were, i can get them to come on intermittently. but they turn off as soon as i let go of the knob. all the other lights work, headlights, directional, hazards, reverse lights, cargo light...
View 4 Replies91 Dodge D150 1/2 ton truck with a 318 (5.2L). Approx. 135K miles. Noticed a leaking freeze plug right behind the starter. Removed the starter & replaced the offending plug. I've also replaced other plugs on the block as needed in the past. While I had the starter out, I went ahead and replaced it as it was getting old & tired. After buttoning everything up while adding coolant, I got a major waterfall coming out between the trans and the engine block.
My project for today is to remove the transmission so I can get to the rear plugs and replace. How many plugs are back there? I'm obviously changing all the plugs back there along with the rear main seal. Is there any advantage going with the brass plugs or should I just stick with the regular ones?
Had a couple bad freeze plugs that made my old 91 D150 with a 318 overheat severely. The truck is repaired but does smoke a little more than it used to at start-up and lasts a little longer. Also when stopped at traffic lights, It will belch a puff upon acceleration. Did the overheat affect oil condition and should I just go ahead and change it? Should I run some Marvel Mystery Oil through it before the change to maybe (hopefully) loosen up the piston rings? I know the valve guide seals are due for replacement but that's another project down the road. I've decided not to do anything with the fuel filter on the Camry...
View 1 Replies1990 Dodge Ram Van.... How hard is this to fix. Some Guys in Los Banos took two days to replace a fuel pump. End result, new pump not grounded so continually drains battery unless I mess with a fuse everytime I start/stop car.
View 2 RepliesMy truck started running a little rough so I replaced plugs, wires (looks like a rat may have nibbled them in places), cap and rotor. The truck idles smoother now but there had been kind of a lurching, almost as though it was bogging down then recovering prior to replacing the parts I have done. Now the issue seems worse, if anything. It seems to be either progressive. If I try to drive the truck like this, it's OK once it's going, though it still sort of hesitates periodically. Getting it going, however, is an exercise in frustration.
It's got virtually no power at all and isn't until it surges forward (recovering?) that it goes at all. I realize this may not be the best description but it's about all I can describe it as. The other oddity is it seems intermittent. Sometimes it'll run flawlessly after warming up, others it doesn't. Today, it ran perfectly for 30 to 40 seconds after first starting it to move between parking spots then it began while driving it. I'm concerned about driving as I don't want to cause damage to the engine and also, it's annoying a heck!
The truck's a 1989 Dodge D100 (not D150 as below; why no D100 option?) with the 318, AT and RWD only with about 225,000 miles on it. Historically, it runs without any issues whatsoever, starts instantly every time I ask it to (even now) and overall is great mechanically. (Ugly as heck but its' a truck!) The only issue I've had with it is recently, the coolant overflow hose came off right by the cap and, apparently, I lost enough coolant to overheat. I noticed the temp gauge registering hot and as I pulled over I got quite a cloud of steam.
It must have heated enough to hit the flash point, I guess. This happened on the freeway but I stopped IMMEDIATELY and it was fine once I put the hose back on and got coolant in it. The engine didn't stall or act up, make noises, etc. That was a month or so ago now. Aside from that and needing the brakes done recently (can't imagine that could be related but who knows) the truck hasn't showed any issues at all. Someone mentioned this could be the Idle Air Control motor but my reading suggests that'd only affect me at idle. Am I mistaken or is there something else I should be looking at?
Where can I purchase a distributor for a 2003 Dodge Neon SE?
The engine is running rough, the gas mileage has degraded, and the Check-Engine light is ON.We went to an AutoParts Store to have them read the car's computer output to tell us why the Check-Engine light is ON.The results said that the No. 4 Cylinder was not firing consistently.We replaced all four spark plugs and the spark plug wires. It ran a little better but the Check-Engine light is still ON and the engine still runs rough. I think we should replace the distributor or maybe just the distributor cap (if possible?).
I was wondering if 1979 Dodge Vans had regular 727 transmissions, or 727 with lock ups? I was told that Chrysler switched to the lock-ups in mid year. How to confirm this? I was also told that if you use a trans on a 318 that had a lock up it would cause a vibration in the drive train at high speeds, and might damage seals in the engine and trans.
View 1 RepliesAnyway I have a 88 s10 blazer that will not start, I've replaced fuel pump, filter, charcoal canister, also the rotor, cap, plug wires, module, pick up coil and ignition coil. Before I changed the pickup, it would start till it warmed up then die, wouldn't start again unless I gave it gas, if I held it steady the rpm would fluctuate but stay running till I let go of the throttle. Now that I've replaced the pickup coil it turns over, I do have spark but it will not start. I bought a code reader all I'm getting is code 12 which is no distributor signal to ecm. Like I said I e replaced both the module and pick up coil.
View 2 RepliesMy car was running perfectly, then one day I parked into my home and that was the last time it started. A mechanic came by and showed me that the distributor was not creating a spark and that I needed a new distributor. I bought one at a junk yard which looked much newer than mine but when we installed it, no spark. I went back and replaced the distributor for another at the same junk yard and the same thing happened, no spark.
I live in a very remote small town and this is the best mechanic that I have found, but they are not sophisticated, no real shops, diagnostic equipment, etc. After going through the expense, trouble, and having my mechanic tell me that it may be the computer, I decided to investigate myself and read a problem that appeared similar to mine indicating that it may be possible that the Crank Position Sensor may be bad.
This is what I read on a post on a different forum: "The first thing I would do is to check out and thest the CRANK SHAFT SENSOR. If this has shorted internally, you may have destroyed the IGNITION MODULE and or the COMPUTER. You might be lucky in that the crank sensor is the only faulty item."
I have a 1950 GMC truck that I restored with a 350 small block v8 with a stock set-up. I now have 30K on the motor and it runs great except for one problem: The module in the HEI distributor keeps failing. The mileage between failures is random: 3k, 5K, 8K. I have now put in 8! I pull the module out and test it: Yep, cooked. I have replaced the cap, coil, and alternator. I think the distributor is not grounded properly. There is no tach attached to it. What is the source of problem? Should I just replace the whole distributor and hope for the best?
View 18 Replieshow long should the bolts be that mount the distributor to the (non-california) 5sfe? I'm putting my car back together (finally) and the only bolts from my pile that fit are one that is too long, and two that are only a couple threads longer than the width of the distributor flange. simplest conclusion is that the latter are the bolts that were there, but does that seem right?
View 4 RepliesI'm going to be freshening up my distributor for my 1950 Cadillac, and I think because of bad weather stripping and other leaks, when it rains heavy, moisture might be getting on the distributor. Is there something I can spray on it that will repel moisture or would just a healthy dose of dielectric grease do the trick?
View 12 RepliesI have a 92 chevy truck with a 350 engine that came out of a 93 chevy my problem is my module in the distributor keeps going bad when i spoke with the previous owner of the motor he told me that he had the same problem and advised me to change the distributor. So I took my distributor out of the original motor and put in but the problem still exist, also I have noticed that I have nearly twice the exhaust coming from the drivers side tail pipe as I do the passengers side.
View 1 RepliesI have a 92 k1500 with the 5.0 L in it. I suspect the distributor drive gear is worn, and even if its not it isn't going to hurt anything to replace it because its the original OEM drive gear and the engine has 233k miles on it. So what I'm looking for step by step process removal and re installation?
View 2 RepliesMy 94 Honda Accord's distributor runs with the ignition switch off. Car will not start. Does this with master relay and 50 amp ignition fuse removed.
View 9 Replies