I have a 2001 Dodge Ram 1500 that I bought used a couple of years ago. About every 20k miles (120k miles on it now) I get a check engine light and upon diagnosis it's the 4th cylinder spark plug fouled out, every time. I change the spark plug, but the old ones are always identical in damage. The porcelain has cracked on the spark plug.
View 17 RepliesI have a 02 F250 with 137 thousand miles. When it had 130 thousand on it I had the plugs changed unknowing that this year 5.4 was known for blowing the plugs.
View 14 RepliesMy son has a 2001 F150 with a 4.6L V8 that's blown a sparkplug from # 3 cylinder. The plug looks as if struck by lightning and has a burn groove as deep as a kitchen match stem the full length of the threads.
How difficult is an engine swap/change using another 4.6L? Neither of us have extensive mechanical backgrounds but plenty of aptitude.
I have a 99 Saturn SL2/auto. Cylinder 1 will not fire. It has spark to the end of the plug. But the cylinder will not fire. No oil is getting on the plug it isn't fouling out. A brand new plug doesn't work at all. The cylinder is DEAD!
View 8 RepliesI have a 1997 F150 4.6 V8 and as we all know these trucks are notorious for the spark plug blowing out. Although when I bought it I never had an issue until we put motorcraft plugs in. After a couple weeks of having these plugs in the porcelain blew out of the plug with the threads still in the head. The spark plug screws into a threaded insert which then screws into the head. We replaced the plug and nearly a month later the porcelain blew again. Replaced it, same story a week and a half later. Before the motorcraft plugs I had autolites in it, and I never had the slightest spark plug blowout problem. Should I just put an autolite in the cylinder that's blowing them?
View 4 RepliesI had the oil changed 2/27/11 drove it home parked it for the night next morning I went out to start it I heard loud clunk. I opened the hood and found a spark plug laying on the head seperate from the spark plug wire. What would make this happen? I have not had the sparks plug changed recently.190,000+ miles.
View 10 RepliesI have a 22R sitting in my celica and my problem is that when I was driving home from school I stopped at a stop sign..... Well I started to take off from the stop sign and as I did Spark plug three blew out of the cylinder... (WTF) well anyways I started it back up and drove it 2 blocks to where I live and it backfired and now I have no spark to any of my wires or spark plugs I checked the Main Engine Relay works just fine, For fuel problems anyways.. other than that I believe my timing skipped during that bad backfire so Woohoo for that but any other problems that could have caused "no spark" like my igniter blew out or my coil.. I would like to know where the fuse is (if any) for the igniter.
View 2 RepliesGetting error code p0302, misfire in 2, pulled the plug and had oil on the treads and on the lower part. My guess is the valve cover gasket, but I'm not 100 percent sure.
View 18 RepliesHow to get the spark plug out of cylinder #4. I have the kit to take out the base of the plug out of the head if it breaks off. But I can't get the plug out. I think the plug broke off but not the electrode. So the electrode is caught up in the porcelain tip of the plug. It's pretty tight back there with the a/c lines and fuel rail and other stuff. I tried needle nose but they just don't grip it right, to get enough force to pull it. These are the plugs with the extended tips.
View 6 RepliesWith the many discussions on F150 spark plug blow outs, is there any consistency in which Cylinders usually go or is it completely random. In my 2003 F150, 4.6, 2wd, I've replaced #3 cylinder with insert and now #2. Currently I'm at 154,000 miles but want to travel cross country with a load. I don't want to stall out on the hwy, would it be wise to go and insert the remaining cylinders - not cheap. My mechanic is willing to inspect with a bore scope the threads and re-torque. Is there a point at which if it hasn't been a problem it won't be. Truck is used primarily for commuting and to pull a single jet ski in the summer. Both blow-outs happened at a stop-light about 20,000 miles apart with no load.
Follow-up. Did inspection, found cylinder #7 nearly stripped out - it was actually pushing up the coil. Funny thing is, this plug had already the small insert which was coming out with the plug. I bought the vehicle new. Was this a factory repair? or did my previous mechanic strip-it when replacing all my plugs at 95,000 miles? Lucking the large inserts my current mechanic uses was able to find some metal and make a good repair. Looking at the cylinder order, I have now replaced 3 of the inter four cylinders (2,3,7) should have I done #6 too, this is probably the next high risk cylinder or not?
I am getting a cylinder 5 misfire and this has been a "on again off again" situation since last August. I took it around to a few places and the general solution was to get new spark plugs. After doing a bit more research I was advised to change the coil cover. I did that and it fixed the problem. Then about 4 months later the light came on again. I happened to change the air filter and the light went off. I though great, problem solved! not so much, when i went to the mountains the other day the light came back on. I did my research again and I have decided to get the plugs changed. Its a 2005 f150 with 94,500 miles on it.
I am told its time to change them regardless. I started calling around and getting quotes and have been told by multiple shops that ford made the plugs in my truck in a bad way. They have been telling me to change them and breaking them is a 50/50 shot. THEN, when they quote me they charge a rate to replace them plus the plugs themself. If they happen to break one then the customer pays for the new one. Do the plugs would really break that easy and should I plan on replacing some of them?
my car sounded very bad and upon raising the hood, noticed a spark plug had blown off. When this happened the steering and brakes got hard to use.
View 4 Replies2001 Ford F350 V10, 220K in crap condition
First of all on the left side 2 of the coils were so withered the rubber separated from the bolt and were loose. Without any tools I was able to remove 2 coils. Typically there is the hole and several inches inside hole is where the spark plug sits.
On cylinder 4 the spark plug is on a funny angle and is level with the hole or possibly poking up above the hole. Tried sticking the ignition coil over the spark plug but it wasn't correct. Leaving it alone until my cousin can take a look. Spark plug was tight but I didn't put a ratchet on it.
Wondering, is this the infamous spark plug blew threw the cylinder thing. Wish I would have taken a picture (I will next time I'm with truck).
Had codes for misfires on 4 cylinders but that was with 2 coils unplugged (way I got truck at auction)....I replaced 3 of them (1/2/6).Cleared codes...4th cylinder remained unplugged....And the only code I got after letting truck idle for 10 minutes was something about ignition coil D (which would line up with cylinder 4 I think).
I need to tap a bigger hole and put in an insert for the spark plug. I can see that the piston is far enough down so that it won't get harmed from the process. But if I don't get the intake and exhaust valves shut, and then use compressed air to blow out what chips I can, and then I start the engine for a few seconds to blow out anything else (with the coil unplugged of course) will a few remaining chips, along with some that may have gotten blown into the intake, be a big problem? It's an aluminum head, so I can't see the chips doing much damage before they go out the exhaust or end up in the oil filter. But I am just guessing. I don't have the tool to test when all the valves are shut. Also, is it possible that a valve might be in the way and get damaged from the tap?
View 11 RepliesI have a Toyota 2001 Echo and after about 5 min of driving, it starts to stutter when I step on the gas and shake back/forth. It gets worse going up hills. Once it starts, it continues at any speed and doesn't have the normal power but doesn't die. Stepping on the gas harder doesn't increase the RPMs like it should. Thinking it might be the spark plugs, I removed the cap on one plug and found the well with about 2 cm of clear, yellow oil. Is this bad? if so, how bad?
View 6 RepliesI somehow managed to kill my 04 Santa Fe 3.5 while doing the dreaded spark plug change and looking for pinpointing and rectifying the problem.
A quick rundown of the car... My mom bought her new in late 03, decided to get a BMW X3 a couple of years ago. I bought her with 65k miles. I just recently had the timing belt replaced by a reputable shop at 79k (yes I know I let it go too long.) I just hit 80k and decided it was also time to do the plugs as I had noticed a decrease in performance and gas mileage of late. Other than the recent dip in performance the car has been extremely reliable and has had no previous issues.
I researched as much as I could knowing that the 3.5 isn't the easiest engine to work on. I bought the recommended Champion plugs that came in the car from the factory as well as the oem Hyundai wires. I also replaced the plenum gasket.
I took my time replacing everything but despite my best efforts, I accidentally cracked the plastic on the radiator reaching over to the back bolts on the plenum. Other than that mishap, the only other issues was the #5 plug sticking which finally came loose after some begging and pleading to the car Gods. Unfortunately, my begging and pleading was enough for them to allow the car to start.
After reading a thread on here, I believe the problem is that I removed the TPS sensor to get to the bolts on the EGR valve, I know now that this was a big mistake. I checked and double checked every connector and can not find one that was missed or disconnected. The car would try to start but would not crank over. I was unable to get any OBD2 codes from my code scanner.
I decided to try a TB from a junkyard and swap it on to see if that was the issue. After swapping it on, the car started and ran like crap for about 15 seconds and stalled out. I was however able to pull some codes in this short time.
The codes I received are:
P0102: Mass Airflow Circuit Low Input.
P110 & P1172: ETS Improper Motor Current.
P1192: ETS Limp home - Target Follow Malfunction.
P2127: Throttle Pedal Position Sensor "E" Circuit. Accelerator Position Sensor 2 Voltage Too Low.
I'm not sure if these codes are left over from before I swapped out the TB or not. I reset the codes after I wrote them down and researched them to see if they reappeared but the car will not start again so I can't get the codes to reappear.
I have a 2001 Hyundai Sante Fe that died on me while driving down my street. The engine sounded like it was loading up for about 1-2 seconds, then it died. It turns over but does not fire.
After a little troubleshooting, I have no spark in cylinders 1 and 4. I swapped the two coils thinking that I had a bad coil, but then the suspected bad coil created spark on the 2-3 cylinder side. So both coils work.
I towed the car to the shop and the mechanic after about 2 hours of billed labor, he is leaning toward a bad ecu. He said there also is no fuel metering from two of the fuel injectors. He checked the resistance on the injectors and said they are fine. He is thinking it is a control/command issue. The car has many other unrelated problems and I am not sure I want to spend too much more money on it.
I am skeptical about a bad ecu. Or sensors that may be causing my two cylinder no spark and alleged fuel problem?
I have an 01 f150 with 5.4 triton. This has been great truck, never really had to do anything to it. It has 195k on it. Week or so ago it started running rough. So I replace the plugs and coils. I noticed some of the plug wells had oil in them. Got done and the truck is running like new.
Not sure where the oil is coming from. Not the piston as the plug was dry on the tip and truck not smoking any. I has began using a quart or so between oil changes. I have always changed it every 3k. Is it just time for new motor. Like I said it is running like new.
I found a leak today on my 2001 Ford F150 Super Crew, 5.4 engine. In the picture, it was leaking to the right of the spark plug, behind the hose. It was bubbling up from the metal. It hasn't been overheating except when I got home and idled with the AC on. What I'm facing?
View 12 RepliesI have a 2001 ford f250 6.8 v10 with just about 183,000 miles on it my wife has been driving it and she told me it was running kinda rough so I took it for a drive and she was right so I pulled #1 COP and found it was full of oil and the same with#2 and #3 had a little bit of oil not as bad. What is causing my plug holes to fill with oil?
View 14 RepliesI have a 2001 Ford Expedition with the 5.4L engine. I know that there are problems with the engines blowing out spark plugs. Besides putting in sleeves and replacing the cover when necessary, any good luck with a different alternative. If not what products with the above options seem to give you the most bang for your buck.
View 16 Replies