My Stratus started blowing the starter fuses occasionally when I tried to crank the engine. It stopped for a while (about three months) but recently started doing it again and much more frequently now.
View 12 RepliesSo I pulled into my driveway yesterday about 5 minutes after my low fuel light came on and as I was making the final turn around my house the engine cut off. Luckily I was able to park in it's normal spot before coming to a halt.
Anyway at first I though "out of gas" even though I knew I'd driven further with the light on. After putting in 3 gallons still no luck. I noticed with the key on no noise from the fuel pump so I checked the fuse and relay both were fine. I then checked all the other fuses and noticed the large 30amp PCM fuse under the hood was blown.
When I replaced it, it blew instantly. I was able to hear the fuel pump come on for a brief second before it blew out. Unsure if the two were related I then pulled the Fuel Pump fuse and replaced the PCM fuse one more time and again it blew. The motor cranks over but won't fire (not getting fuel.) Where I can start to correct the issue.
2003 f150 supercrew with 166,000 on it. Daily driver. Keeps randomly blowing 10A fuse under dash that controls ABS4X4 urn signals. No routine causes. Just blows at random times. Fuses were blowing instantly upon replacing then stopped. Doesn't blow when turning switches for turn signals or when turning it to 4x4. Just does it randomly. Sometimes will go months without blowing. Tore dash apart and can't find any wiring issues there. Could be somewhere else? Is ABS4X4. Turn signals going bad?
View 6 RepliesI'm having a problem with my 2003 Elantra. Occasionally it hesitates (acts like it is going to run out of gas). When it does this the a/c stops blowing cold. Lasts for 3-4 minutes. Most recent time it had 1/2 tank of gas. I also have a problem putting gas in. I have to fill it very slowly or the gas pump will keep clicking off. I don't know if they are related or not. What fuel problem will affect the a/c?
View 1 RepliesI had a problem with this issue a few months ago, was 45 minutes away from home, blew the fuse to the starter. Switched another one in, blew it too. Had it towed to a shop, they did some diagnostics, felt like it was a short in the starter, replaced it and all has been well (as far as that particular issue) until this morning. Got in it, turned the key it cranked for less than a second and stopped. I pull the fuse, sure enough, blown. Swap it with another, it blows.
I know I have a bare wire in the column, the OD light wire is chaffed, I fixed it before but it must be worn again because I can get it to light up depending on positioning of the shifter lever and as I recall, every time the fuse blows the steering wheel is cranked to the left.
I have a 2001 Olds Alero. The AC compressor went out so my father in law and I replaced it. It worked fine for about one month, not it keeps blowing the a 10 amp fuse (can't remember which one at this moment, my wife is at the store with the car). I have been told that it is a bad wire, I can't see any pinche wires and have looked up to where the wires go into the tape/plastic casing. I have also been told that it is the compressor that is doing it (the parts store said this was not the case... I think they just don't wanna warranty anything).
View 12 RepliesUpon trying to start my 2003 f250, it keeps blowing the 15A "Transmission Range Sensor then to Starter Relay Coil" fuse. Initially the truck would still start if i did not use the aftermarket Viper keyless start. however, now it doesn't start at all and keeps blowing fuses. I contacted the guy that installed the alarm thinking it might be something on his end. He walked me through reconnecting the factory starter wires which would isolate the issue if it was something on his end. it's still blowing fuses. battery terminals are good and clean.
View 3 Replies92 PA Base
It's that time again for vehicle inspection and my horn has been blowing fuses. I had it diagnosed by the dealership and they stated the horn pad inside the steering wheel is bad. They also stated the horn pads for my model of PA has been discontinued and that I should install an aftermarket horn. If I don't have this horn installed I'll fail the inspection.
So I just got a new Passport Radar for the car and noticed that im getting no power...Checked the fuse box and and fuse was blown...replace it and the fuse blows automatically.
View 6 RepliesSo I installed my XS HID low beams and fogs a couple of weeks ago, and everything was working fantastic. However, when I installed my LED turns and load resistors, whenever I turn on the low beams, the inline 30A fuse pops. The HID fogs continue to work. The switchback turns work great, and I have never got any hyperflashing.
I have checked all the connections, and they all seem strong. I have used the diagram I found on here from exLEDshop outlining all the connections on the pin array for the headlight harness. I am tapped into the blue wire on the driver's side for + turn and the black for -, and the black w/orange stripe on the passenger side for + turn, and the black for -. If I accidentally have the load resistors connected to the wrong wire, would the turns hyperflash?
I know that it would be better if I used grounding points on the chassis for the load resistors, but could this be causing the short? Or could bad ballasts that are the culprit? The only reason I'm leaning away from it being the ballasts is because they worked fine until I put the load resistors in.
I just got my led switch back lights in for my 08 camry. But I have run into a problem I have installed all four led signal lights (switch backs in the front and led ambers in the back) and the led flash relay for my car. What is happening is that the led will turn on for a couple of seconds and then the fuse for the signal lights burns out both the one under the dash and the one under the hood.
View 3 RepliesI've blown my turn signal fuse for 3 times until the relay burned out. Now I have had cleaned turn signal switch (with CC) from all of the old stuff in there and replaced hazard switch. But it happens again! After 5 minutes driving, both fuses (7,5 AMP for turn signals and 15 AMP hazard) blown out. I'm afraid there are some shorts in wirings.
I'm looking for the wiring diagrams or any other users experience in this matter... Where shall I start from?
There was a water leakage behind and under drivers seat. I removed trims etc. to lift the carpet to take the Comfort Module for checking as there were some weird thing in overall car electric systems (central locking, saloon lightnings, electric windows and dropping gauges on instrument panel. I found a small amount of water in container, where the module is placed, but on the electric parts weren't any water marks... Also it's impossible to connect to the CCM via vag-com.
Several weeks ago, my wife drove our Outback for 10 minutes, turned the car off, then turned it back on after 10 minutes. After 15 minutes of its being on the second time and the car being in a car line, the red temperature indicator blinked, then went solid. She pulled over to let it cool, then put coolant in the overflow reservoir when she got home. The reservoir was nearly empty. The very next day, the exact same thing happened, in the exact same sequence - 10 minutes on, 10 off, 15 minutes on in a car line, then indicator came on again.
I took it to a mechanic who could not reproduce the issue after letting it run for four hours. He replaced the fuses and told us to bring him the car when the problem recurred. Reservoir tank is full, no blockage in line from radiator to overflow tank.
The next day, for a third time, the car overheated in the pickup line. We brought it in the following day. The mechanic finally was able to reproduce the issue. He said that both fans (a subi outback has two) needed to be replaced, as they were drawing a tremendous amount. He advised that I take it to subaru to find out if there was anything they could do re: warranty.
I took it to subaru, who said that the fans are not now under warranty (we have 65k on the car). I decided to have them replace the fans anyway, so I asked them for a diagnosis. However, after two days in the shop, they were unable to reproduce the problem. They ran the car in idle, they tried to recreate the stop-and-go/standstill environment of a carline, but no luck. They said that the fans were drawing the expected amount and that they would need recreate in order to diagnose.
I have two questions:
1) Should I replace the fans myself? I can either take the car back to the first mechanic and have him replace the fans or I can do it myself. I can do basic jobs like oil changes, replacing serpentine belts, but I'm not sure what nuances are involved with replacing anything electrical.
2) Most importantly: What would cause both fans in a relatively young subi to spike their amperage draw intermittently? I guess it's possible that i just got two bad fans, but that doesn't seem to be a common problem with this model. So, I want to make sure that this issue is not indicative of some other underlying problem.
Suddenly my 2007 Sonata Limited trunk and gas lid fuse keeps blowing.
I'm not an electrical guy so I don't know how to check with a meter, I oiled the latches. My car was rear ended near the tank lid/bumper area a few years ago, but everything worked fine til recently.
I can replace the fuse, but after a few uses it will blow, sometimes it will blow without being used. I can't tell if it's the trunk or gas lid causing the problem because nothing will happen immediately, Basically I am only finding out my fuse blew when I need to use it.
Where I could look to inspect the wiring for kinks or it's connection run?
About 11pm 2 nights ago on our way to Florida, hit a nasty bump on I-95 in SC and there went the fuse to the tail lights and dash lights (#17 I believe). Obviously something shook loose from the jarring of that bump and blew the fuse. I've blown this fuse before, but I thought it was due to a cracked LR tail light assembly holding water, which was replaced last weekend.
Now I replace the fuse, and as soon as I hit the headlight switch...it blows again. Holding my breath running around FL at night until the man pulls me over for no tail lights. So far, here's what work has been done:
- Replaced entire LR tail light assembly with new one, new bulbs, new bulb plugs - Sprayed electrical cleaner all over harness plugs, and used electrical grease to hook it back up
- Sprayed electrical cleaner into both trailer plugs
- Did replace both batteries last weekend - noticed on the drivers side battery appears to be some relays next to the battery on the fenders - one appeared to be beat up probably due to prior battery replacements - no clue what they do
I am at a total loss. Worse fear is I can't figure this out and I have to turn it over to the dealership
Why the rear Auxiliary A/C blower on a 2004 Sport Trac keeps blowing fuses and how to fix it?
View 12 RepliesI have an '03 F350 6.0 that occasionally wouldn't start until it had cooled off for about 30 minutes. A friend of mine recommended adding a little marvel mystery oil to the oil system, I did research this and found no negative posts, but now it has been 2 hours and it still won't start. Could i have added too much and thinned the oil out too much?
View 7 RepliesHaving an issue with my car blowing fuel pump fuses every once in a while under heavy to moderate acceleration. Have replaced inline fuel filter and the fuel pump resister(white ceramic part). Runs fine with normal driving, but when I want to get some horses out of it, it will cut out and stall and once i replace blown fuse it will start back up again, and I'm off and running again.
View 2 RepliesCar is a 2002 b5.5 1.8t sedan.
Bought the DDM Tuning HIDs, 3500k 35w for the fogs, installed with no problems. Also ordered the 5000k 35w for the low beams. Installed them, they flickered on for a second, then nothing. Let the ballasts charge for a while but still nothing. Called DDM, they said my car needs a error code eliminator kit thing later they were at my doorstep. Plugged one side in, flicked on then nothing. Thought both sides might need the code eliminators plugged in...wrong. both flickered on, and then nothing. Tried again, no flicker, both low beam fuses burned. Plugged the regular bulbs in, changed the fuses, lights working again.
I don't know much about electrical, but DDM said i def don't need a relay kit. Do I need a relay kit? Or would putting higher amperage fuses in the place of the original ones work? if so what amperage?
My wife's AC quit blowing air last week (a '05 Nissan Altima), so I decided to check all the fuses before just replacing the blower motor. I pulled all fuses out in all three fuse boxes and didn't find any blown. Got a call from an upset wife later that day saying she could not shift the car out of park. Currently, she is driving it by using a screwdriver to release the safety switch next to the shifter.
View 3 RepliesMy 2003 Dodge Neon started overheating. We replaced the thermostat, temperature sending unit, flushed the radiator, checked for blockages, cleaned the radiator, changed the head gasket and water pump.It can run for about 10-15 minutes driving or 30 minutes idling before it overheats. The fans will kick on. The thermostat opens up. Pressure builds up on the radiator hose. When it gets hot, it boils back into the reservoir.I've been careful not to let it get into the red since the head gasket change.We sent the head off and had it planed.
View 9 Replies