I had an engine swap recently done on a 2005 Honda Civic, and within a couple days, Check Engine light came on. Mechanic ran the error code and I have to apparently replace the camshaft position sensor. They are claiming that the sensor was not replaced in the engine swap, and so not covered by any warranty.
View 10 RepliesI have a 2007 Camry V6. Last weekend, I changed all the spark plugs and five ignition coils. (117,000 miles on car). In January, I replaced the #6 ignition coil. Last week i threw a code for the #2 coil. Fearing the domino affect, I replaced all five remaining coils and changed all 6 spark plugs while i was in there.
Now I am throwing code P0368. This happened immediately after i changed the coils and plugs. What is this about!?!?!? Ive driven it maybe 40 miles since the plug/coil change...engine light is on the whole time. Is this sensor bad or does my car need time to "rethink" with all these new parts ...
I've got a 2003 Jetta Wolfsberg that is acting up, I'll do my best to describe and outline the steps I've taken with the mechanic to fix the problem,
Occasionally, when starting the car one of two things happens, (1) engine turns over, fires, and then dies. Removing the key, letting the car sit for 30 seconds and trying again usually gets the car started. (2) The car will start but will run VERY roughly (misfiring, sounding like the engine is choking out). Very much like this (only sometimes much worse, usually ending in a stall): [URL] ....
Turning the car off, removing the key, letting it sit, and then trying it again will eventually work, even though it might take a few cycles. Once the car gets running it almost always runs fine from thereon. (There have been a couple occasions where the car has gone into limp mode, even on the freeway. Pulling over, letting it sit, and starting it again almost always fixes the problem. I've not yet been stranded.)
Diagnosis & Steps taken:
I get regular codes for the camshaft position sensor and also for the MAP (Barometric pressure) sensor. Both have been replaced.The MAP sensor and the atmospheric pressure readings are off by about 30 (something like 960 and 990). My mechanic thought that maybe it was an electrical problem, he noted that the two sensors mentioned above share a common ground. He replaced the ground because it looked corroded. This brought the pressure numbers both to 990 and the car ran perfectly for a few weeks.One thought was to splice in a new wire to the MAP sensor, to see whether it was a signal problem, this hasn't been done yet. Another possibility was that there is a problem with the ECM.
I THINK, that the problems began just after having the computer flashed at the dealership two years ago. I'd got a code about an update and so the dealership did this. I don't know whether this could have had any effect on these problems, but the times lined up too well to not mention it.
06 sonata 3.3 L V6. Light has been on for a month or two...took it in to mechanic yesterday and it's a camshaft position sensor error...it makes total sense to me now because my cars been starting hard, seems like it gets hotter then usual...and had a "clicking" noise for about 10 mins, then gradually goes away. it takes a few extra cranks now to start the engine unless it was already fired up.
Also does a jerk once and a while around 40 km/h. I looked online and those seem to all be symptoms of a failed camshaft position sensor (CMP). Would those symptoms seem about right? Am I okay to drive slowly for the weekend before I get the new sensor installed? The mechanic didn't seem to worries about me driving for just the weekend...but it's worrying me a bit...
1996 Ford Explorer on a small island with no mechanics. Vehicle does less than 100 miles per year, never over 20 mph. The check engine light came on and the code reader says it's a problem with the Camshaft Position Sensor. The vehicle runs fine, just as it did before the check engine light came on. I'm tempted to put some electrical tape over the check engine light and keep driving.
View 2 Replies33k Civic 2001 "PO335 Crankshaft Position Sensor A circuit" error code
My Civic 2001 LX (non vtec 1.7) threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining.
My Civic 2001 LX (non vtec 1.7) 33k threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining. So much for a reliable honda.
Wasn't there a TSB for this? I've searched Google and Vortex with nothing for the MKVI but I could swear I read something on this.
I am accumulating oil/grim right around the sensor and it's beginning to irritate me. I want to take her to the dealer but would rather know for sure of any possible TSB out there so I have something to reference.
The CEL just came on in my 20th AE Gti. The code indicates a Camshaft Position Sensor issue. Don't know where this sensor lives under the hood of the GTI? Is an easy enough fix for a beginner to attempt? (have hand tools, former bike mechanic, but no shop just a parking lot in the Texas sun!)
View 6 RepliesSo my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 RepliesMy 1.5L 2000 Hyundai accent is reading p0342 code.(cmp sensor circuit low Input). I have changed out the sensor from a parts car and it's still reading this code. I've read it could be timing or an issue with the starter wiring.
View 3 RepliesI am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?
Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 RepliesI have been getting a P0011 error code. Changed the OCV but the code continues. I'm going to try replacing the CMPS but am not quite sure of the location on the 2007 Sonata GLS. Looking for any pics of the location or a description?
View 1 RepliesWhere the camshaft position sensor is on a Mazda Protege5 2003. I can't seem to find any information about this particular car.
View 2 RepliesMy check engine light came on about a week ago and was unsure what the problem was. So I tested the codes and it said that the camshaft position sensor was bad. So I have tried finding this sensor but little to no luck. I was unsure if it was the 2 or 3 pin, but after looking at some pictures of the engine I'm thinking it is a 2 pin. I attached two pictures of what I think might be the sensor? But I am unsure. This was right next to the timing belt cover, which is where it said it was located. I have a 1996 Ford Ranger, 2.3L.
View 6 RepliesI am getting the code for the camshaft position sensor. Erase code, comes back immediately. I don't even think this car has a camshaft position sensor.. I guess the first step would be locating the little bugger. Crankshaft position sensor is new and seems to work fine. Car is running btw.
View 5 RepliesI have replaced the camshaft pos sensor multiple times from Autozone (warranty ) and replaced with one from Advance Auto still get cam sensor code changed crankshaft sensor today still running like crap, stuttering. I have also done a complete tune up and the Distributor has not been pulled.
View 1 RepliesThe computer is returning P1379 camshaft position sensor. Where is this sensor located on a 2002 Toyota Camry 2.4L and how easy would you rate the job of replacing it?
View 3 RepliesShe is a 1999.5 Golf 2.0 (although, she just has a rabbit symbol on the hatch, is she a Rabbit or did someone remove the Golf badge?) I just bought the car, with less than 160,000 miles. The dome lights work sometimes, Door Ding works intermittently as well, but sometimes will "glitch" in other words it will be making the sound but it kind of stutters? Odd? The horn sometimes works, however it is very silent? Check engine light is on with a camshaft position sensor code and miss on cylinder 3. Someone told me to replace the "109 relay"... could this be the problem or is this the CCM?
View 5 RepliesI have a 2004 MK4 Golf 2.0l that's been throwing a CPS error code. My brother was going to come down to visit for a weekend. He had done some diagnostic work and had me order a timing kit and a camshaft position sensor from ECS.
So, with my assembled parts, I brought the car in to a reputable shop. Anyway, the guy does the work and now the car is ready and saying that the CPS took nearly 4 hours more of work.