Civic - Honda :: 1997 - CEL Came On With Error Code PO135?
Nov 28, 2011
I have a 97 Honda Civic Manual transmission and my Check Engine Light Came On. The error code is P0135 which shows up as needing a O2 sensor. My question is:
1. Do I need to replace it?
2. How long do I have to replace it?
3. Will driving with it as it hurt my car?
The weather is getting colder and I read that could be the cause. I really don't have much extra money but I don't want to kill the car. I have kept up on Oil Changes with MaxLife Full Synthetic, Radiator Flush, etc if that matters. I also went into Valoviline Instant Oil Change and they double checked all of the fluid levels and that was OK.
View 11 Replies
Advertisement
33k Civic 2001 "PO335 Crankshaft Position Sensor A circuit" error code
My Civic 2001 LX (non vtec 1.7) threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining.
View 4 Replies
My Civic 2001 LX (non vtec 1.7) 33k threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining. So much for a reliable honda.
View 4 Replies
I have a 98 1.6L Honda Civic DX with 200,000 miles and standard transmission. It was running great. Then I was going up a steep hill and it lost all power plus no rev from gas peddle. after tapping the gas it started powering again. CE light was flashing and staid on. The next day the light went off but the problem kept happening and sometimes the light would come on. It started stalling in 1st gear sometimes(not having power when I first hit gas)but then it would catch and pick up. then when shifting into 2nd or third gear it would loose power again but then catch. I got codes read p0302 and p1399. problem got worse and worse. now car won't start. it turns over and almost sounds like it will, but doesn't, ignite. I also noticed there's too much oil in tank from last oil change. My mechanic has no idea.
View 5 Replies
I have a 01 f150 7700 with a 5.4L and its throwing codes po135, po155, po174, and po171. Here is the history, last year had same code and found it was a bad ELLBOW on pcv hose, replaced and that fixed it, I also had a crack on egr valve and I replaced that too. This Jan truck was running bad in the morning and I traced it to a bad idle air controller, replaced it. I got a code and guy said I had a bad pcv valve so I replaced it.
About 3 weeks ago check engine light came back on with the 4 codes listed above, I replaced both front o2 sensors, 250,000 mile so I thought that was it but came back same code, I took it to a local mechanic and he said that the intake gaskets need replaced, but he call me later and said I had no leaks on the intake and that he did find another vac leak. He didn't charge me anything and sent me on my way.
I drove the truck about 50 miles and same codes back, so to recap I have cleaned mad sensor, replaced both front o2 sensors, a new egr valve, a new idle air control, pcv valve, pcv hose and ELLBOW, don't know what to look at next. Any clues?
View 4 Replies
I have an 02 Civic EX. Engine light has been on for over a year, runs just fine. Reading misfires on 3 cyl, and cat code. I have since: changed all plugs and coils, changed both front and rear o2 sensors....switched coils around to see if code misfires changed (yes).
I see this is a common problem but no one has a solution..? I'd rather NOT change the cat converter and pay for that only to find out the light stays on. Need to smog so I can sell!
View 7 Replies
I have a 96 Honda Civic CX. The check engine light came on the other day while it was raining (don't know if the rain had anything to do with it) and now it comes on every time I start the car until it warms up. Once in a while it comes back while driving but that's rare. I tried to get the code with a cheap reader and it didn't show that anything is wrong. I then took it to an auto parts place and they used one of their nice readers to scan it and told me that everything is fine. What's the next step?
View 7 Replies
I have a 1997 Honda Civic with 275,000 miles on it. After driving for an hour or so, it starts getting hot when stopped or nearly stopped. It goes back to normal temperature when I start driving. It does cool down if I turn on the heater. I just changed the timing belt/water pump and put it a new radiator and changed the thermostat hoping it would solve the problem, but it hasn't. I checked and the fan does come on when stopped. Could it be a cooling system clog that a flush might be able to solve or might it be the head gasket?
View 9 Replies
I recently had some work done on my 97 Honda Civic (manual), and asked them to adjust the parking brake while they were at it. They tightened it up as they usually do when they work on the car (the other work was not brake-related, although they DID replace my master cylinder just back in February). Two days later, my brakes began to fail (much like they had when I needed the master cylinder replaced). Turns out, something happened with the parking brake such that the cables seized or something and caused the regular brakes to overheat. Once they cooled down, the regular brakes were fine again, so they disconnected one of the cables for the parking brake and ordered replacement cables to be installed next week, for a not inconsequential sum. My question is: did they screw up when they adjusted the parking brake, such that I shouldn't really have to pay the full amount for this subsequent repair? Or was this likely inevitable?
View 12 Replies
I have a '97 Honda Civic w/ about 168k miles, am hoping to get at least another year or two out of it before I go looking for a used Honda Fit or something similarly budget-minded to replace it. I just ran the A/C on cold for the first time this season (I realize I was running it all winter when I defrosted the windows), and it was clearly not working, just blowing hot air. Now, the last time I had anything done with the A/C was in 2005, when I was in a minor accident and the very nice mechanic flushed it and replaced the freon (if I have that right) for no extra charge in the course of uncrumpling the front of the car for me.
Which brings up two issues:
1) I no longer have a trustworthy mechanic where I live, and have had much difficulty finding one, and
2) the car already has a salvage title so is worth about $500 max.
Now, obviously it is worth more than that to me, since it will still be cheaper to fix than get anything else, but I have the impression that A/C repair could get quite expensive, and it is enough to make me wonder if I could afford the monthly payment and insurance increase on that used Honda Fit..
View 15 Replies
In recent months there is a new noise in my 97 Civic (75,000 miles). In any hard turn and particularly on U-turns there is a grumbling sound which seems to come from the front end. The noise doesn't happen on gentle turns. It grumbles a bit on 90 degree turns and wholeheartedly grumbles on U-turns. I checked the power steering resevoir and it is full so it is between the lines.
View 2 Replies
I had plugs and wires changed to try clear code. Car seemed to do some better but while trying to go up a steep hill car started stuttering and jerking. Power went out of car and check engine light started blinking fast. After let the car sit for bout 45mins car started running fine again and light stopped flashing but remained on. Code read cylinder2 misfire again.
View 1 Replies
Honda Civic, 2003, around 180k miles. Code P1457 is showing, no drive ability problems. Everything seems to point to the evap canister valve as a common problem. I crawl under next weekend and start replacing parts...
View 5 Replies
2004 Honda Civic with 166000 miles.
--Had Check Engine light on for a couple days and code reader said P0135. Parts guy said this means "Bank 1", my Haynes book calls this code for " Primary Sensor 1" Is this the same as "Upstream"?
--Replaced O2 sensor (Denso 192400-1160 05F12) myself with a new one (Bosch 15710). Fit perfectly, plugged right in.
--Check engine light goes off for about 5 minutes but comes back on with code P0134.
What should I do now? I replaced the sensor closer to the engine before the catalytic converter. Very easy to reach from the top. I rented the correct tools and did not damage or force anything. Is there a second O2 sensor after the cat that is not so easy to reach? Was that the one I needed to replace? Did I misunderstand the meaning of "upstream" or "Bank 1"?
View 12 Replies
Tried to start my car this morning and nothing .(headlight switch was off),checked the battery and it read less than 1 volt (did return to 5 volts after being disconnected for a while). Drove the day before with no apparent problems or lights. Battery is a die hard gold about a year and a half old. checked pos battery cable to ground read 1.8 ohms went up into the high k ohms when I removed the horn/stop fuse(which was good) .Also after market alarm installed. Am I chasing gremlins or did the battery just suddenly die.
View 6 Replies
Car is a 97 civic. I had a input shaft bearing replaced since i had the tranny off. I decided to change the flywheel clutch and bearings. After install I have cold not shift into gears with engine running. I fixed the problem by removing almost all of the free play in the pedal. Should i replace the master to get some of the free play back in the pedal?
Second and main problem, when i release the clutch pedal there is a ratchet/grinding noise. It changes with engine revving and the further out the pedal the louder the noise. I think i attached a noise clip. I have dropped my transmission to ensure everything is installed correctly. reinstalled the tranny with the same noise. Bleeding the clutch did not work either. Pedal does seems soft but not getting stuck.
New parts:
Flywheel
Pilot bearing
Clutch disc
Pressure plate throwout bearing
Transmission Synchs
Bearing kit
View 6 Replies
I have a 1997 Honda Civic w/ about 150k miles on it. The belt was changed a little under 2 yrs ago. Just started making a high-pitched sound when backing up. Sounds like a note on a flute, and doesn't sound like grinding. It only happens when backing up. As soon as I stop, shift and go forward the sound goes away. Began 2-days ago. I try to find parking spaces where I don't have to back up.
View 6 Replies
Recently had a new water pump and radiator put in my car. Not so sure if they are "new" but anyway.
The car does not seem to use coolant it has only slowly flowed back into the reserve tank over time spilling over a little.
View 17 Replies
I have a 1997 Honda Civic that I was given by an elderly neighbor's daughter after the elderly lady went to the grocery and ended up 100 miles away when she could not figure out how to get home. The car was smogged at the beginning of the year but when I got it ran very rough and the temp went nearly to overheating on the drive home when I was stuck in stop and go traffic.I found the radiator fluid level low and an oily residue inside the radiator water bottle. I took it to a mechanic to check it out and was told it had a blown head gasket and maybe worse.
I am thinking of buying a rebuilt cylinder head and replacing it myself but I am not sure how to diagnose if any other damage could have been caused to the engine. It's hard to know but I am guessing that the engine was damaged during the 100 mile road trip due to low coolant level. It turns out short term memory loss was the diagnosis for my elderly neighbor. I filled the coolant level and ran the engine for a bit and the temp stayed normal but the rough running remains. The oil dip stick shows no signs of coolant in the oil and the coolant looks bright green when I looked in the radiator after topping it up with some water.
Any way to detect if I could be facing bigger issues like failed bearings? I am OK to do the head replacement but an engine replacement starts to get into the realm of what it would cost to get another car of the same age.
View 18 Replies
I have a 1997 Honda Civic 5-speed with about 200,000 miles. It is making a low-pitched whining noise when I let the clutch out in neutral. I took it to a mechanic who immediately diagnosed it as the throw out bearing. Being mechanically inclined, I dropped the tranny and changed the clutch and bearing, but started it back up, and the noise is still there - as if I did nothing at all. It is not constant volume - sometimes it is louder than others. It is usually loudest first start of the day. I live in Houston, so its not like it is "cold", just not hot. To be fair to the mechanic, the bearing was quite corroded, but everything else seemed to be working properly.
View 13 Replies
I own a 1997 Honda Civic EX. Automatic. 160,000 miles. I have had the front disk rotors and pads replaced five (5) times within the past two years due to "warped" rotor issue. I recently changed the two front calipers as well to rule out caliper issues. Yet I continually end up with a warped right front rotor weeks after putting on new rotors. Here is what happens. Car brakes fine for a week or two with the new rotors. Then shortly afterwards, the right front rotor (passenger side) quickly develops a rubbing -like noise (not a grinding noise) when braking at a low speed. It's not a constant rubbing noise but a rhythmic swoosh swoosh swoosh noise as the tire rotates and the brake is softly applied. You can feel it in the brake pedal. This noise eventually gets louder and louder the more I use the brakes (or, the hotter they get?). It can also cause the steering wheel to vibrate at certain speeds when braking.
I have had it into four different mechanics.
Mechanic 1: Your rotor is warped.
Mechanic 2: You are too hard on your brakes causing the rotor to warp.
Mechanic 3: Did you go through a puddle of water lately?
Mechanic 4: You need new brakes. Period.
This is getting ridiculous. In all my years of driving, I have never encountered this problem. I am not hard on my brakes. I do not believe the "water puddle" theory at all. I should mention, although these are not oem rotors. they are not some cheap Chinese ones either. Something must be causing this rotor to "warp" if it's really warping at all. I have had the tires rotated to rule out a bent rim. It happens no matter what tire is on the right front car. What could be causing this? A bad front end alignment... bad wheel bearing... (although no mechanic ever indicated that as a problem)... bent splash guard... bad master cylinder? Air in the brake lines... old brake fluid???
View 3 Replies
