Chrysler - Ptcruiser :: Horn / Turn Signals / Hazards / Door Ding Doesn't Work?
Dec 22, 2013
I have had this problem for a while now, but can't seem to figure it out. I'm sure it's an electrical issue, but I'm not that great with electrical. My turn signals don't click when I push the handle in either direction. The turn signals come on and stay on but don't blink like they should. I checked the lights in the front and back and they just stay on but don't blink. Also my hazards don't blink. They just stay on and don't make clicking noise either. My horn doesn't work and my door doesn't ding with the key still in the ignition but in the off position. I don't know of it's all related or different issues.
View 10 Replies
Advertisement
I just changed the multi-function switch on my 2001 PT Cruiser, because someone suggested it since my turn signals were not blinking or clicking. The turn signals come on, but do not blink or make that clicking sound at all. They just stay on. The hazards do not blink or click either. Lights and all work fine. It's just the turn signals and hazards that do not. What else controls the clicking and blinking of the turn signals and flashers. Could it be the relay that's inside the multi-function switch? I'm almost 100% sure we checked all the fuses, but I could be missing something.
View 1 Replies
Today, I replaced the flexible coupling in my steering column. All went well and seemed great until I realized my turn signals were not working. I tried the hazards and promptly heard the 10amp fuse blow. I took the paneling back off and realized that the wire bundle to the turn signal was being pinched above the steering column.
After lowering the front of the column down and removing the wires, I noticed that there was some damage. One wire (blue) was cut and a few others had damage to the sleeves. I repaired the sleeves and fixed the broken wire. The turn signals now work perfectly fine, but when I activate the hazards all the signals go dark. I cannot find any blown fuses and the relay appears to be working just fine for the turn signals.
View 2 Replies
I recently bought an 08 Sonata from a used car dealer which has 65,xxx miles. Last week my turn signals would work intermittently, and now neither the turn signals or the hazards work. I put in a new relay and a new turn signal switch, to no avail. When I turn the hazards on, the relay clicks once then nothing. When I do the turn signals, nothing clicks. Is there another relay I'm missing somewhere?
View 14 Replies
I have checked all fuses, checked wires on top of steering column all checked out ok. Hazards work but when I press brake tail lights just blink with no brake light but the 3rd brake light works??? Signal switch maybe??
View 14 Replies
2000 V10 F250 - daughter is using my truck and called to tell me the turn signals weren't working. She called me shortly after and said she adjusted the tilt and hazard lights came on and now she can't turn them off. I had her pull the hazard fuse to stop them. She then noticed the brake light weren't working. I don't know if the brake lights were because she pulled the fuse or she just noticed they weren't working.
A week or two ago, she said she parked the truck, turned it off and took the keys. When she came back out, the truck had rolled across the street. Periodically, over the years, I would go to start the truck and nothing happened. I would shift the gear selector in and out of drive. Then the truck started.
Finally, since I've owned the truck, the when I activated the left turn signal, the selector frequently wouldn't stay "locked" till I turned. So, are these related? Do I have multiple issues going on in the steering column. Where to start looking when she gets the truck home?
View 3 Replies
Every time I step on the brakes, there is a bright spark in fuse #13. My brake lights, turn signals and hazards don't work. At this point my truck isn't drivable.
According to the owner's manual in my truck, says circuit #13 is for "stop lamps, CHMSL/hazard, trailer tow stop lamp, and speed control."
I'm assuming that the hazard part covers the turn signals as well, but I know the cruise control works even when the fuse is blown. I used it last night on the way home (this was before I realized I didn't have brake lights).
So I know I have a short somewhere. The only mods I've done to the lights are aftermarket headlights, but if the fuse only gets blown when I step on the brakes, I don't see what that would have to do with it. Also, the lights have been installed and working for about a month before this started. The only thing that I did around the same time was install the gauges. I ran the power to them from #5, the customer access circuit.
Are there any other "common" areas for this to happen? I already removed the rear brake lights and it didn't work. I am quickly running out of 20A mini fuses.
View 9 Replies
I just found a nice Prius C for sale with little damage to the front right corner, no frame damage or anything, just some bodywork needed. So, after it was fixed up. I brought the car back and there is weird issue that I have - turn signals and Hazard lights dont work. When I turn it on, i can hear clicks from it, but I dont see lights blinking on the dashboard and my head/tail lights dont blink as well.
View 5 Replies
When it is hot out and the interior of the car gets really hot these things do not work: the electric windows will not work, the turn signals will not work, the display on the air conditioner does not work the blower on the air will not work but the air will come out of the defroster. All the dash lights come on abs, trac on trac off. After the car sits in the shade for at least an hour all these things will work.
View 1 Replies
I have a no spark no fuel situation. But my check engine light does not come on and my clock does not work. My turn signals dont work on the dash and the bulbs. But my hazerds work fine. 1997 yukon 5.7L...
View 7 Replies
In my 97 Ford Taurus the turn signals and hazards are not working. I changed the fuses, but still no luck. Someone mentioned that there might be another fuse box under the hood (besides the maxi fuse box). Also someone mentioned the blinker fluid being low.
View 14 Replies
So all about the same time as far as I can tell, some electrical type issues cropped up.
This Always happens
The Horn is now making a lower pitch wimpy sound
These Next two, when they happen, seem to happen at the same time:
The 'Hey you left your Lights' on Chime does not always Ding
The Drivers Side Rear passenger Door Lock does not lock/unlock
Since they happen intermittently it would not seem like a fuse issue, more like a relay or loose connector?
View 1 Replies
2004 Prius here. The turn signals and hazard lights stopped working a few days ago. I found a disconnection in the grounding and repaired it. Also replaced the fuse and the flasher switch. Now the lights work, and I can hear the flasher switch clicking, but they don't blink!
View 13 Replies
I used the volt meter wrong while testing my turn signal bulbs for power and not they do not work (or hazard lights).
View 3 Replies
A/C works fine when moving. At idle, it doesn't work. Fan is not spinning. Is it definitely a bad fan or is it a possible fuse/switch/module? How difficult it would be for a novice to replace the fan?
View 2 Replies
I've driven home from a tree nursery with a utility trailer - hazards on at about 60kph. Took me about twenty minutes to get home. It's a pretty warm day so AC was on. I turned the hazards off to signal turns and then put it back on when it was straight road.
After disconnecting the trailer and later driving to pick up the kids, I noticed the turn signals wouldn't blink but the hazards would still work. The AC would not respond, nor would any of the climate control buttons. The heated seat controls are dead and also the 12V DC outlet next to the seat switches seems to be dead. However, the airbag compressor control still functions normally, the diff lock button still works fine, the headlights and hi-beams still work as well.
I took a few minutes when I reached the first school to check through the fuse box under the hood but there wasn't anything obvious. I'm also considering just removing the negative on the battery to reset the computer. Then, there' s the window thing....
View 6 Replies
I drive a 98 Ford Contour Sport. When I was driving today, I signaled a left turn, and the signal began working erratically. This also happened with a right turn, and, since I deliver sandwiches, happened when I turned my hazards on. Throughout the day it got worse, and eventually stopped working. I'm willing to bet that it's a wiring issue since all of my fuses are fine.
View 5 Replies
Well, on our way home during my leave, the wife made the comment about halfway home that the blinkers had quit working. I assumed it was probably a fuse or relay, so we came on home. I have been looking at it for a few days now (too hot to spend too much time out crawling around under the dash ) and I am still having some trouble. My brake lights, and hazards are not working, and neither is the cruise, which was working fine while I drove before the blinkers went out.
I have no power at all to the flasher relay. I replaced the brake light switch because it was definitely worn and looked a little burned inside when I pulled it out and inspected, but still nothing. Have not found any fuses blown. Brake pressure switch fused link harness seems good with my test light. Wipers, brights, everything else on the turn signal switch works fine. Can't even get the cruise to go into diagnostic mode, it only blinks once when I try.
View 5 Replies
So I have an 04 F250 Super Duty 6.0L and suddenly the turn signals and hazards stopped working. First I replaced the switch on the steering column...no luck. Today I replaced the flasher relay under the dash panel (the blue one)...still no luck. I remember checking fuses in the fuse box but don't remember which ones I checked but I didn't see anything obvious. I also took a quick look under the dash at all the wires for any anomalies...nothing. I'm lost... What to do next!?
View 1 Replies
Dad borrowed truck and wired 7 pin trailer harness. Lights worked on truck/trailer for use but upon return the turn signals didnt work. Hazards and running and brake lights did work. Replaced TS flasher and Haz flasher. Still no signals. Pulled steering wheel and replaced turn signal cam only, not whole switch. Now no brake lights, no rear hazards or turn signals. Losing my marbles trying to follow schematic and using test light and mulit meter. All bulbs and fuses are good. Running lights and head lights working as well.
View 6 Replies
2005 F350 Super Duty. I have no brake lights turn signals or hazards. dealer suggested the multiswitch but changed it and still not working?
View 2 Replies
