Chrysler - Ptcruiser :: 2002 - Engine Service Light Won't Go Off After Servicing
Aug 25, 2012
I have a 2002 Chrysler PT Cruiser manual transmission with 91,420 miles. The engine service light came on over a month ago (today Aug. 24, 2012). Little by little, a major tune up, a new battery, new plugs, O2 censors, condenser, wires, PVC valve, new gas cap, gas treatment, two tanks of premium gas, the light would not cut off. So off to the Auto Zone to get analyzed twice the code was P0601. Researching the internet, this P0601 code meant the PCM needed to be reprogrammed by the dealer. I called a Chrysler dealer here in Austin and was told that reprogramming the PCM may or may not cut the light off. So today and $100.00 later, the PCM was reprogrammed and the light was off when I left the dealership this morning. But it turned back on when I was leaving work this afternoon. My car needs the annual state inspection and it will not pass.
View 7 Replies
Advertisement
I have a 2002 PT Cruiser who's airbag light seems to go on and off randomly. Some days it will stay off all day. Other times it will stay lit for days on end.
Some times it will go off for 10 to 20 seconds, then come back on with a chime for 10 seconds, then off again. Off...on...off...on....it will do it for 45 minutes or so or until the car is shut off and restarted.
Occasionally, the light coming on seems to correspond with hitting a pot hole or rough patch, but that could just be coincidence because it is not consistent.
Both the driver and passenger airbags were replaced about a year ago, during round 1 of fixing this problem (to get through state inspection.) It worked for about a year, and now its back. It makes me think I was taken for almost $2,000 replacing those in the first place. The steering wheel clockspring was also replaced around the same time.
I see from searching online that I am not the only one that has seen this with this model car.
View 6 Replies
I have a 2005 PT Cruiser convertible. 3 times now ghetto accelerator has stuck down. The engine light comes on and after stomping on the pedal and releasing it, the car does not want to accelerate and sitters as if it will cut out. After about a minute everything clears up and works normally. I have taken the car into 3 repair shops including the dealership and they cannot recreate the problem ...
View 6 Replies
My engine light went on when driving about 45mph. At same time engine began to bog down, then accelerate - then bog down again.Car is a 04 pt cruiser, Chrysler 4 cylinder Engine light still on and it starts but it seems to be running roughly.
View 6 Replies
I have a 2004 W8 Passat wagon. I just went over 60,000 miles and was wondering how to reset the service warning for coolant servicing.
View 1 Replies
I have a 2002 chrysler pt cruiser. For the past week when I start to crank it it will just click one or two times then crank. Today it won't start at all just clicking.
View 2 Replies
I'm trying to find the power steering pressure switch for a 2002 PT Cruiser. I have been under the car and located a pump on the passenger side with a two prong connector. The connector looks to be in good shape. I thought the switch was replaceable but there was nothing to screw out only two prongs going in. Am I looking at the wrong part and if so where is the power steering pump?
View 4 Replies
Yesterday afternoon the "Service Engine Soon" light turned on in our '97 Town & Country (3.8L engine). A few minutes later (while I headed to Autozone to get the code read) the light went out. They were still able to retrieve 2 codes: P0700 and P1775. Internet searches suggest a possible bad solenoid pack for the transmission.
More background: The van has 161,000 miles, and the original owners got the transmission replaced at 40,000 miles under warranty (4 speed automatic). The transmission fluid was replaced (pan drop method) at about 153,000 miles and at 112,000 miles, etc., with Chrysler ATF +4 fluid. The van got new plugs and wires about 15,000 miles ago. (It also got a new radiator and hoses yesterday morning which I think is unrelated.) Another possible clue: On long trips sometimes the 2nd transmission shift will become slightly rough but it still shifts and after it has rested everything returns to normal. This occasional shifting issue has been going on for over 5 years and again when it manifests itself it is very slight.
View 2 Replies
After running for a while traveling to and from the store, my temperature gauge on my 2005 PT cruiser rises to hot and the temperature light comes on. However,when I get out and raise the hood. The engine doesn't seem to be overly hot. No boiling or hissing sound and no steam coming from the engine.
View 3 Replies
my car is a 2007 Chrysler PT Cruiser with over 75K on it. My problem is two fold. First, recently the right rear turn signal light shorts out but only in the morning it seems. Because we've been getting a lot of rain in Nashville and the surrounding area, I suspect the high dewpoint and humidity might play a part here but I think I just need to replace the bulb.The second issue is a little more annoying. For whatever reason, the "air bag warning" light on the driver side console comes on and I cannot figure out why.The third issue is a little more pressing. I noticed during the summer whenever I was idling and had the A/C running, occasionally I would hear the engine act like it was about to stall out, like RPMs had dropped significantly. Now I've noticed it does that when the front defroster is running and winter is coming. What can I do about any of these problems listed here?
View 7 Replies
I just wanted to post this due to the problem I was having with this code. I recently replaced a broken timing belt on my 2005 pt cruiser (non-turbo). Everything went back together, minus the hours trying to get the timing marks lined up by myself. After getting the engine buttoned up, the car would crank and idle, but only after 2000 rpm and the engine code P0016 would show up. I went back into the engine, reset the timing belt, and cranked it before putting everything back together. Worked fine, so buttoned it back up and took it for a test drive.
Bam, same engine code pops up again, only this time the car acted like it wanted to go into limp mode for half a second after driving for a few miles when I was turning around to come back to the house. It straightened up and drove fine. I could drive the car fine even after that, made a few test drives into town. The car would kind of fight limp mode after first cranking the car and accelerating, but then straighten up.
After a couple of months of research and talking to a friend who is a pretty good mechanic, I decided this was an electrical problem. I checked, and sure enough, after looking at the wiring at the cam shaft sensor connector, it was frayed. I spliced it and still had some issues with the code. I had just put a new sensor on it when the belt broke thinking it might be the sensor, so I put the old sensor back on it and now it runs fine, no more light. So, after months of thinking the timing or tone rings might be off, it was just a wiring/sensor issue.
View 7 Replies
I have a 2005 PT Cruiser non-turbo. A short time back, the tensioner bolt broke on the alternator and after spending several months going back and forth with the dealer, I was finally able to find the correct size bolt to replace it. Shortly afterwards, I began to hear a scraping sound coming from the engine compartment. The sound is sporadic, and only lasts for a short time. The sound only appears to happen when the engine is idling down when coming to a stop, and it doesn't always do it.
It doesn't make the noise when accelerating, in fact, the noise quits when I accelerate. The noise sounds like metal being drug on concrete, or a grinding sound. Is this a possible bearing going out on the alternator or possibly the AC clutch/bearing? The noise is not present during normal driving conditions, just when the car is almost at a stop and stops as acceleration occurs. I have reached in to see if possibly a loose pulley/bad bearing on the alternator, but there is no slack there. Is it possible that I have the alternator belt too tight, or is this another issue?
View 11 Replies
My '06 Pt Cruiser A/C works fine @ speed, but idling and @ stop lights it blows moist warmish air and idles roughly.
View 7 Replies
When ever the car stops at a traffic light or stop sign, the air compressor cycles rapidly and the cool air turns warm. I was told the cooling fan was not coming on, but the other day the fan was cycling and the cool air stayed cool. My question is what controls the cooling fan operation? It seems the high pressure switch is working correctly and the fan motor is working. As long as I'm driving the air is cool.
View 2 Replies
Any way to reset this so it goes out?
View 1 Replies
I have an '02 GMC,Sierra,4.8 L 5-speed,once upon a time this truck would easily travel over 500 miles on a full tank of fuel, for the first 10 years ,on a road trip ( which I do every summer), approx.,210 miles one way, this truck would still have just over 1/2 tank of fuel, as of the summer of 2012, the thing used up to 3/4's of a tank.
Then the service engine light came on, I replaced all sensors, O2's new injectors, motorvac, new plugs ,wires etc,( All done by a certified ASE mechanic). After his work the truck got back up to the aforementioned "good mileage", and the Service engine light went out...for awhile, now it is on again, as mentioned earlier, the truck has basically had a complete tune-up. So whats up with this ?? I sure hope I don't need to R/R the engine itself....
View 3 Replies
2002 Infinity QX4: Why the Service Engine Light appeared 2 days after 3 emission sensors were replaced?
View 6 Replies
2002 7.3 ...On my way home tonight, my Service engine soon light came on. How can I pull the code to see whats going on?
View 14 Replies
The "service engine soon" light is on. I got code 0141 on the code reader. The repair manual for my F150 is stating that the code is for bank 1 sensor 2.I want to check the sensor, but I don't know the location of bank 1 sensor 2. I would like your advice as to the location of the sensor, and what should I check for?
View 9 Replies
Driving while in 4x4 HI up a hill the truck started to slip. I stopped, shifted to neutral, and engaged 4x4 Low. I shifted back to drive and started moving up the hill. The engine started to lose power and the "Service Engine Soon" light began to blink. I put the truck in park. As I let it run a little bit, the engine started to shake as if something was very imbalanced. I went to check under the hood, and confirmed that it was shaking quite noticeably. There was no grinding or clattering of any kind though.
I turned the truck off for a bit, and then restarted. There was no light or shaking upon starting up; but as soon as I put it in gear and started driving I could tell it was losing power, the light came back on, and the shaking ensued. This occurred in 2wd, and both 4wd lo and hi. I parked it at a neighbors place and there it sits for now.
I plan to try and get the codes read. My other vehicles can't make it through the snow we have right now, but it is suppose to get warm later today and might melt enough for me to get one out. I also live out in the country, so the nearest auto parts place is about 20 miles. Same with a dealership service shop. I'm hoping I can buy and return a code reader from an auto parts store to assess if this is something I can diagnose myself or not.
It is the 6.0l gas engine with the 4sp automatic transmission. The truck also has about 107,000 miles.
View 16 Replies
Got a 2002 GT with the NA 3.8 and 150,000 miles. The car has pretty much sat for the past 6 months, driven very sparingly. If it's been sitting for a while (like over night or longer) it will start no problem. If I turn the car off for a shorter period, it will crank but not fire. It will start only if I pump the gas as I'm turning the ignition.
In addition, on occasions it has died while at idle or coasting to a stoplight. After it dies it will fire back up no problem.
Fuel problem perhaps?
The "Service Engine Soon" light has been on for about a month before it started acting up. I had the codes checked at AutoZone and it came up with P0442 and P0128.
View 12 Replies
