Chrysler - Newyorker :: 1993 - Mechanical Whirring Noise When Brake Pedal Pressed?
Nov 14, 2011
I am looking to purchase a 1993 Chrysler New Yorker and when I test drove it I noticed that every time the brake pedal was pushed a mechanical whirring noise was audible. This happened every time the brake was pushed whether the car was moving or not. The car brakes seemed to work fine and there were no other noises associated with normal brake problems. The noise seemed to come from inside the car. What that might be? Also, any other reasons to not buy a 93 New Yorker with about 115,000 miles on it for cheap?
View 1 Replies
Advertisement
I was wondering if this problem is the "Barking" noise that keeps coming up the search or is it another problem. I will include a link to the video down below.
To start off, the Prius is 2010 Prius II and has 120k miles on it. Great Car. Only other problem was AC compressor dying at 90k.
The chirping noise happens when the brake pedal is pressed and does not go away until the release the pedal. It makes the noise regardless of whether the car is on or off.
It makes the noise when the car is stopped and or when the mechanical brake engage at between 0 and 6 mph.
Noise does not occur when the brake switch is removed. Not valid solution since the brake lights will stay on. It does not affect the performance of braking.
Here is the link to the video .... .... ....
View 9 Replies
I have a 2008 Ford Escape, and today I noticed that while backing out of my driveway (downhill) as I pressed the brake pedal it made this grinding noise, but when I got out of the car I looked through the tires and the rotors and pads were fine. I did not get a chance to check the inner side of the rotor or pad yet. What else could this noise be if it's not the brakes? It only makes this noise when I press the brake pedal which is why I thought it was the brakes.
View 3 Replies
I have a '77 Chrysler New Yorker with the 450 engine. I'm told the electronic leaning module is out and apparently unreplaceable: can't find any parts anywhere. The car won't run w/o it. Somebody said I could maybe install some sort of after market carb conversion?
View 1 Replies
I have a 92 (3.3L) New Yorker 5th Avenue that has makes the car jerk badly going uphill and occasionally makes a backfire / misfire noise. It is a general jerking, not localized (right / left front) by feel. It starts ok and runs smoothly at idle but once you put it in drive and start acceleration, it begins to jerk. It has over 200k mi. I have had the fuel filter replaced, new plugs and plug wires put on. Mechanics have ran codes on the engine and transmission and tell me that no bad codes show up.
View 5 Replies
I have an 88 New Yorker whose digital amp gauge swings between its lowest and highest setting this makes the audio command center report electrical malfunction service immediately. Shortly after the car dies it will restart after 15 to 30 minutes. It doesn't throw any relevant codes, has had the alternator replaced still no luck.
View 8 Replies
Ok, did an intake manifold cleaning on my 99 Accord the other day, and now I have problems...
Long story short, some time ago my car started to have a very rough idle. Took me awhile to find the problem. Turned out the air hose, between the filter and throttle body, had developed a big hole on the underside. So I replaced it and while I was at it used some throttle body cleaner, spraying into the intake manifold chamber. Lot of junk blew out the tailpipe. The car ran much better, but the idle could still be a little rough. I ran it that way for awhile, and finally the other day decided there was probably still some junk in there and it was time to really clean it out. So I took ff the throttle body and intake manifold housing. There was a lot of junk in there! The small intake on the passenger side was completely clogged shut. (I understand this isn't surprising on these cars.) I used a bunch of rags and 2 cans of Valvoline throttle body cleaner and a lot of elbow grease and cleaned it out. I was thinking to myself that whatever I didn't get with the rags flushed through OK, but I didn't want to take the whole intake manifold out.
So I put it all back together. (I took a video before I started, so I'm pretty sure it's all back together right.) But now I have problems. The car starts. It idles fine mostly, but can be a bit rough. But the trouble starts when I put the pedal down. If I do it in Park, well, if I push it quick the engine just dies. If I push it slow, the engine revs then quits, revs and quits, over and over. Similar if it's in gear. If I push it hard, the engine stalls. If I push it gentle, it revs up, but chugs along a bit.
I've run some seafoam through it, thinking it was clogged up with all that junk, and sure enough, lots of smoke comes out, but nothing is improving so far. What have I done wrong?
View 19 Replies
I own a 04 Grand Cherokee and have recently had problems with my passenger side brake light. Now the light itself does work under normal running light conditions, but when I go to press the brake pedal it doesn't engage the bright brake light. Drivers side works fine and so do all my other lights, I replaced the bulb to no avail, and am now currently looking into replacing the bulb socket.
View 1 Replies
Today I faced another problem i just try to start my car but, due the dead 12v battery it didn't start so i pressed the BRAKE PEDAL until it reach the bottom, again i tried to press but its not going to the bottom why was that, is it due to dead battery? And last time i called an automobile expertise to jump start my car. They check the voltage with a digital multi-meter and he said me if you jump start even you will get this problem again until u replace the new battery. but i said him it doesn't matter do a jump start and finally it was ok . Now again I faced the same problem and this time i am going to change the battery.
View 1 Replies
When I press the pedal down the pedal vibrates and make an odd sound like errrrrrrrrrrrr best way I can explain it...
View 5 Replies
My 2004 Chrysler Sebring with 128K miles is making a loud whirring noise when I accelerate. It does not happen when I break, coast or am idle. I live in a city and potholes are a way of life. I got four new tires in November and had the alignment checked and fixed at the time. What it could be?
View 2 Replies
Requiring that the brake pedal be depressed in order to start the engine can be a nuisance, say if the driver is out of the vehicle and the passenger wants to start the engine to run the A/C, etc.
There is a workaround though. Press the engine start switch once to go into ACC mode, then press and hold it for 15 seconds and the engine will start without the brake pedal having to be pressed.
View 14 Replies
When brake pedal is fully pressed and my car is in drive the pedal vibrates. The only thing I thought of is that my intake is touching something, but I don't see anything.
View 8 Replies
Sometimes my 96 Subaru Legacy will not turnover unless the brake pedal is pressed. Other times starts without my foot on the pedal. It seems to need the brake pedal addition more often if it has sat a couple hours or more without being started.
View 5 Replies
My Sonata 2008 2.4 produces a single click as I press brake pedal, somewhere half way through. You can hear it and feel it with your foot. I think it clicks somewhere inside the hydraulic system of the brake.
View 13 Replies
Noticed when I press brake pedal brake lights does not work even the center one. Checked all fused in the car and the small ones under the hood. All fine. I have a long trip tomorrow. Where else i can look. Everything seems working. Reverse light is fine. Is that related to latest brake light switch recall? Cant think of anything else.
View 4 Replies
07 Chrysler Town & Country with 86K. It's been happening off and on for about a year now. On long highway trips when I'm driving fast (maybe more when it's cold), a whirring noise will build up. It starts quiet and can get really loud. When I get off the highway, the engine noise goes down and the whirring noise is really obvious. I take my foot off the accelerator and the whirring noise continues for about 10 seconds. When I hit the gas again (this time at city speeds, 30 mph or so), the whirring noise instantly comes back and can get high pitched and LOUD, almost like an old police siren.
Last time it happened, I popped the hood to track down the source. It seemed to be coming from the engine block. When you're looking down at it, it's coming from the left side, directly under the drive belt (but not the belt).
View 1 Replies
2007 Chrysler Town & Country, 72k. It's happened twice now. On long interstate trips, over 50 miles, the engine starts to make a loud whirring/humming sound. The temp and RPM gauge looks fine. The first time it happened, I checked the dipstick and it was very low (I was overdue for an oil change). I topped it off and it went away for a few weeks but then it came back, after about 100 miles running it 75 mph or so. Then the oil was fine. Pulled off and let it cool for 30 minutes and it was fine but I drove slower. It seems to come on while I'm on the interstate and the engine noise covers it until I get off and then it's very loud. Maybe it seems to get louder when I take my foot off the gas.
View 4 Replies
I have 2013 Elantra ( 20,000 miles) and when I put the brake lights on without the headlights on everything works ok but when the headlights are on the driver's side brake light does not come on when the brake pedal is pressed. I thought it was a bulb problem so I replaced it but I am still having the same issue. What is going on? I know it is still under warranty but I figured I could handle a burnt bulb issue but that was not it. I noticed that the drivers side bulb is not as bright either when brake is pressed without headlights
View 11 Replies
To all 2014 and 2015 GX 460 owners, does brake pedal have a slight modulation or vibration while press it. Feels like ABS but not as strong pumping action.
When I step on the brakes the first time feels normal and then I let go of the brakes, then I press it the second time that is when I feel a slight modulation or vibration of the brake pedal.
View 14 Replies
After my local brake shop changed the front rotors and brake pads on my 99 grand cherokee the brake pedal is spongy and long, almost reaching the floor. They don't know why. Apparently they had a problem with fitting the new pads. I took it to the jeep dealer and they told me the master brake cylinder was leaking and needed to be replaced. many hundreds of dollars later the brakes are still spongy and long and does not correct with repeated pumping. The dealer was also stumped and I complained that nothing changed with the new master cylinder. what might be the problem?
View 4 Replies
