I own a 2004 Silverado 1500. Nearly every time I drive, I loose temperature control on the driver's side after about 15 minutes of running the engine. The passenger's side seems to be working fine. I'm not sure if it is a bad rheostat on the driver's side or a bigger issue.
View 6 RepliesI have a 1993 Chevy Silverado rwd automatic 350 5.7. It died on me on the way to work this morning. It slowly lost power and acceleration. The lights and radio all worked. When I tried to restart, it tried to start but then just cranked like it had no fuel or spark.
I had it towed home and checked the following things. I removed the fuel filter, it is clear. I verified that the fuel pump was working by turn the key to the on position while the filter was off. Good stream of fuel. I verified that there was fuel to the TBI. Good spray while cranking. I verified that there was spark by pulling a plug out, connecting to the wire and cranking the engine. Spark seemed weak but there was spark. The front plugs were dry, but the rear plugs, especially #8 was very wet. I verified the timing by pulling the #1 plug, removing the distributor cap and checked the rotor position. I bumped the engine to get the #1 piston to the top of the cylinder and the rotor was point directly at the #1 plug wire. The cap, rotor, plugs and wires are only 1 month old.
I also tried to check the ignition coil by disconnecting the coil wire from coil, and slid the boot back to expose the contact. I held it just of the coil while the engine was cranked, but did not actually see a spark at the coil. I did not hear any arcing. I pulled another plug and checked for spark. Again i had spark. Just seems weak to me. I am on my way to the auto parts store to get a new coil.
The cruise control on my 2002 Chevy 1/2 ton Silverado doesn't work. Went to boneyard and bought a module but it didn't fix my issue. Borrowed a multimeter and tested the cruise control module plugin. The only pin that came up with a incorrect reading was the first brake test. It's suppose to have 12 volts with brake pedal up but showed about 30, so I changed the brake light switch. Still no cruise control.
Since I have a high reading on the brake pin, do you think I have a wire issue there or would my problem be in the multi switch wires by the steering wheel?
My wife was driving the 1999 K3500 7.4 model ls crewcab truck home the other day and out of the blue it started running rough popping and back firing and lost power. It had a major tune up about 40,000 miles ago. It sometimes has a hard time cranking to start, but once it starts it idles really rough and pops and smells like it is running rich. I thought the distributor cap but it looks fine, could it be a sensor?
View 2 RepliesI purchased my 92 Silverado in Dec. 2008. Since I got it the temperature control display has been blinking 'A/C' for 2 minutes after starting, than goes away. From the owner's manual and the GM service manual I realize this means there is a problem in the A/C system. I figured that it was low on refrigerant since the compressor clutch would never kick on, that and that is what it typically has been in the past with other older vehicles. After buying the retrofit 134a kit, I recovered the stuff that was in it, then proceeded to add the new stuff.
The pressure kept rising but the clutch never engaged. I looked through the GM service manual and they suggested to do the obvious. Is there power to the wires i.e. the cycling switch and the clutch positive wire. There was not. I inserted a jumper on the cycling wires figuring this would complete the circuit telling me if the switch was bad or not. With jumping the cycling switch I still had nothing, the clutch never engaged. My next thought was well maybe the internal clutch relay or the pump was shot. So I ran a jumper from the positive post of the battery, to the positive post on the clutch relay itself. Then the clutch kicked in, I sucked in the 134a and everything was working. I also did this to the cycling switch, when I added power the clutch engaged and all worked.
This tells me I have an electrical issue and the mechanical stuff should work. I don't believe that it would be the cycling switch because with it jumped it should engage the clutch of the compressor and it did not, In fact it did nothing with a jumper on the cycling wires. I assume that I have an issue elsewhere that is causing a dead spot in the system or else the cycling switch would have power to it.
My owner's manual states that I should change my transmission fluid and filter at 100,000 miles for a vehicle that experiences "normal" driving. My question is this- should I follow the owners manual on this or change out the fluid and filter at 75,000 miles? I just turned 70,000 miles and the fluid is not showing any signs of burnt material it and it still looks and "smells" healthy. Oh, I would consider myself a "normal" driver as well. The vehicle is a 2004 Chevy Silverado 4x4 with the 5.3 L engine.
View 14 RepliesIt was a cold winter in Boston in the last two months. And since then almost every time I started my 2005 Prius, the temperature was default to 75F. Also, the first time I start the car in a day, it almost show the outside temperature as Celsius instead of Fahrenheit unless I press the screen to display something else and then come back, then the Fahrenheit will come back.
View 9 RepliesI've got a 2001 Chevy Prizm (160,000 miles) Starts right up-after I drive for awhile and turn the engine off. It won't restart at times - I have to wait anywhere between 5 and 20 minutes till the engine will start again. The engine cranks - so it's not the starter or the battery.
View 4 RepliesBasically the car LS 2003 V8 had an issue with the thermostat....this was necessary be changed after 50 miles of drive the car....in the last 4 miles the temperature increased in a short period time to the high limit...with the protective system the car was turn off.....one time with the mechanical service the follow items was changed: thermostat, radiator, coolant temperature sensor, water pump, plastic joint parts (housings), head seals, coolant and the 2 caps (radiator & coolant tank), this last was damaged by the pressure during the over heating.
After all parts changed I still continue having in the car the high temperature in 8-10 minutes of continue engine operation, after this period time the car turn off automatically by the safety system.
I need information about the coolant flow in the system, the pump pulley rotation, the belt installation, the manner and values to test the old temperature sensor, auxiliary pump and the current CTS (cylinder temperature sensor).
The fan motor is working good, none coolant leak is present, and I already test without thermostat (none change in the result).
I have checked the fuses and they are all good. I turn on the headlights and the dash lights do come on at that point but I have no power to the buttons on the panel or any of the climate settings.
View 3 RepliesI have this weird noise that comes from the engine compartment and you only hear it when the A/C compressor is running and the gears are engaged while braking. It sounds like a low whirr that goes on for a few seconds. I noticed that if I shift into neutral and engage the brakes while the A/C is running the sound does not come on, also if I have noticed that there is no noise if the A/C is OFF. Could that be the compressor? the idler pulley? the belt tensioner??
View 4 RepliesI have a 98 chevy truck that won't start. After it sits. It was starting after cycling the key a few times. But now it won't start. Could it be the pump? I hear it running.
Or could it be the regulator? It was running good after it started. No check engine light, no gas smell, and no rough idle.
I've got a 2004 Silverado 2500, crewcab, longbed with a 8100cc gas engine. The truck has 80,000 miles and is in great condition. There's just one little problem - the climate cntrol system will occassionally go to completely hot. When it started a couple years ago, it was weeks between occurences. Now it's about every day and can be multiple times a day. When the system goes to hot, the only way to get back to the proper setting is to turn off the ignition and then restart.
It was happening on both the driver and passenger sides, but the first attempt to repair this issue was to change the envirenmental control computer - now the heat only happens on the driver side. The passenger side remains as set.
why my truck is running rough the problem I am having is when you push the gas peddle more than a 1/4 of an inch it shudders and has no get up and go and also if say I'm doing 40 MPH and hit the gas you can hear the engine rev up but I will lose all power and actually lose speed I thought maybe the cats were bad and I changed the plugs for good measure but I can't seem to figure it out also I had the fuel pressure checked and its pulling pressure is great/
View 6 RepliesI have a 92 chevy truck with a 350 engine that came out of a 93 chevy my problem is my module in the distributor keeps going bad when i spoke with the previous owner of the motor he told me that he had the same problem and advised me to change the distributor. So I took my distributor out of the original motor and put in but the problem still exist, also I have noticed that I have nearly twice the exhaust coming from the drivers side tail pipe as I do the passengers side.
View 1 RepliesOn my 1999 Chevy Silverado Z71, a gurgling water sound is present everytime I accelerate. Are there any other Chevy owners that have had this same problem? If so, how was it resolved?
View 14 RepliesThe issue I'm having is the A/C. When I got the truck the A/C was completely freezing. Recently however, the compressor was having issues not engaging and I fixed that by simply plugging the cord to the accumulator thing. . Now the compressor engages, but is not cooling really at all. It is an old truck and the compressor is a little worn from what I see maybe 2mm space when not engaged. I checked the levels of freon/coolant with a gauge and the amount is perfectly fine. Plus there seems to be no leaks.
View 1 RepliesI have a 1993 Chevy Silverado, 350, 2WD. It has a 4L60E transmission. I just started having a problem shifting from 1st to 2nd. When accelerating the RPM's go way up and won't shift until I let off the throttle. Then it shifts into all other gears normally.
If I accelerate slowly. it will shift into 2nd at about 16 MPH. It will then shift into all other gears normally. I have replaced the Throttle Position Sensor, flushed the transmission and replaced the filter and fluid. This made know change in performance.
I am now suspecting that it might be the 1-2 shift solenoid. The check engine light is not on and everything else works fine.
I have a 98 Chevy truck with a 4L60E. It has no second gear. I was sitting in park for about 10 minutes with the engine running, then put it in drive and it never shifted into second. It felt like it went straight to 3rd. I played with it manually until I figured out I had reverse, 1st, 3rd, 4th and torque converter lockup, just no second gear. My acceleration rate was medium and when I reach about 27-28 mph it would shift from 1st into 3rd. It has 230K on it so I rebuilt it with all the typical parts - frictions, steels, band, sun shell etc., still no second. I then pulled the pan back off and replaced the spacer plate and put in a shift kit. While I had it down I put a corvette servo in and did an air check. It worked fine. I could feel the band tighten.
Both the 1-2 and 2-3 solenoids checked good at 23 ohms. I swapped their positions to see if it would make a difference. I also checked to make sure the 1-2 accumulator piston wasn't stuck in its bore, the spring was new from the shift kit. It was fine. Put it back together...still no second gear. When I originally pulled the pan off for the rebuild, the pan was free of any debris and was very clean. I then drove it a couple of miles to a local transmission shop. They put their scan tool on it and drove it around the block. There were no codes and the ECM was calling for second gear. It doesn't sound mechanical since almost all the parts have been replaced, rebuilt or inspected that affect the 1-2 shift. It sounds electrical. Is there anything I have missed?
I picked up a very clean 2008 Silverado 2500 HD. W/60K miles. The vehicle has been very well cared for as I know the orignal owner. I have zero complaints with the truck other than an annoying front end clunking. Its very reminiscent to the intermediate shaft issues of my 2003 2500HD.
Basically when hitting very small road imperfections, I can feel/hear a clunking in the front suspension. I can also duplicate the issue by rocking the truck left to right with the steering wheel while going 20-30MPH. I figured, stabilizer links. I put the truck up in the air, & can't find a thing wrong. Links are tight as well as the ball joints & tie rod ends. Were these trucks know for a common clunk like this.
My dad's 1996 Chevy Silverado will not shift into hi gear. The truck starts up fine and he can drive it but for some reason it won't shift into hi gear. Him and I are clueless as to why it won't. He has a 1996 Chevy Silverado, 6.5 liter V-8 automatic transmission, and its a diesel. We really want to fix the truck ourselves so we are trying to avoid taking it to a shop.
View 2 Replies