01 2500hd, 8.1L allison auto, push button 4x4. wont lock in until its about 2000 rpm then will release just fine. Just not sure of where to start looking for the problem. Actuator on the axle or in the transfer case or something else?
View 2 RepliesI picked up a very clean 2008 Silverado 2500 HD. W/60K miles. The vehicle has been very well cared for as I know the orignal owner. I have zero complaints with the truck other than an annoying front end clunking. Its very reminiscent to the intermediate shaft issues of my 2003 2500HD.
Basically when hitting very small road imperfections, I can feel/hear a clunking in the front suspension. I can also duplicate the issue by rocking the truck left to right with the steering wheel while going 20-30MPH. I figured, stabilizer links. I put the truck up in the air, & can't find a thing wrong. Links are tight as well as the ball joints & tie rod ends. Were these trucks know for a common clunk like this.
My crew cab 2001 has 75K miles and is well maintained and garaged. Every once in a while the engine will just quit while driving just as if the key was turned to neutral all dash indicators light up but just quits running. Turn the key to start and hear the engine cranking but won't start. Sometime in park it just cranks however I noticed that when I move the shift lever into neutral and depress the brake it will crank and start sometimes.
I don't believe it's a fuel problem. Could it be a loose wire in the column?
I have been trying to self diagnose an issue with my pick up for a while now. I have an 01 Silverado 2500HD 6.0 that shifts really hard into all gears. I was told it was the transmission going out, so we replaced the transmission with a rebuilt one and it did nothing for the shifting issues. We then had the transfer case rebuilt which also did nothing for our problems. My father who has some general mechanic knowledge is certain that the free floating rear end is not turning with the correct timing for the transmission shifting. No check engine lights come on at all during these issues. When I took it to a mechanic he told me I needed a new transmission and blew me off when I told him it was just replaced.
View 3 RepliesI have a 2001 2500HD P/U with the 8.1L V8. I have owned the truck for ~5yrs and used it with everything towing. For about the last three years, I have noticed that when the truck is in gear (Either Rev. or Drive) the engine idle almost acts like it is missing. It doesn't do this at higher RPM's (say over 1K) while driving.
Last spring I did a tune up (Plugs and wires) and a few of the plugs had quite a bit of build up so I figured that was what was causing the issue. For about 1wk after the tune up it seemed to clear things up (at least I didn't notice it), but then resurfaced.
My question is: should the "Coil" parts that feed each spark plug need replacing, or could they cause this symptom? The ignition system on this truck is a bit different that what I am used to seeing, so I am not sure where I should start looking for the problem.
Also, there are no error codes being thrown.
My dad's 1996 Chevy Silverado will not shift into hi gear. The truck starts up fine and he can drive it but for some reason it won't shift into hi gear. Him and I are clueless as to why it won't. He has a 1996 Chevy Silverado, 6.5 liter V-8 automatic transmission, and its a diesel. We really want to fix the truck ourselves so we are trying to avoid taking it to a shop.
View 2 RepliesI have a 96 chevy Silverado 4x4 5.7 motor and it does the same thing but it doesn't leave in first gear, it misfires and high rpms and doesn't go in overdrive. but if I drive a little while and turn it off, it's fine it acts like a normal truck would. then if my truck is off for more that a couple of hours it goes back to it acting up.
View 1 RepliesI have a 92 chevy pick up 5.7 with 159,000 miles. The truck runs and starts great but shortly after I bought it 3 years ago it developed a sort of misfire at higher rpm's, it's fine if I drive it normally but if I try to pass someone it will downshift then fall on it's face, (spit,sputter and slow down). some times I can feather the accelerator and it will come back again. I normally don't drive the truck in the winter but this week I was forced to use it and the cold weather is seriously affecting it, it took forever to get it up to 70 mph after getting on the highway. once up to speed it will do 75 all day without an issue.
I've replaced the plugs, wires, pulled the throttle body and cleaned it as the port for the pcv valve was plugged solid with carbon. I have not replaced the cap and rotor as they seemed to look fine. I have not checked the fuel pressure because it will break the tires loose upon take off and I don't think that would be possible if the pressure was low, would it?
I am having a bad time with my 2006 2500HD 4x4 with the 6.0. First the battery was beginning to act like it was running down, getting weaker and weaker every time I started up truck. So finally truck died at the gas pump. I pulled battery (optima red top), and took it over to NAPA to test. Battery tested fine on top posts, but was acting funny with the side posts.
So, I purchased a new Redtop, and installed and and clunk, truck wont turn over! So, back to Napa to buy a new starter, install starter, hook up battery and now the sucker turns over great but will not start at all. Truck threw 6 codes: P0335, C0035, U1026, U1041, C0040, C0055.
Wiring all looks fine, battery looks new, and I have changed nothing but battery and starter.
I have a 2001 Chevy half ton 4wd. It has the 5.3L, 4L60E transmission, and a 246 transfer. I am having problems with shifting. if I out the truck in drive, the trans will wind out in 1st gear and not shift. I then pull it down to 2nd and it will shift. When it comes time for third gear, it will not shift at all. It just simply revs until it catches up with the speed at which the truck is rolling. I thought it was a bad tranny as I smoked one and replaced it with a used one so we rebuilt the tranny and it still does the exact same thing. Also the speedo is not working but the odometer is on. Don't know if its registering anything but its on. I have also checked every single fuse and maxi fuse in the engine compartment and the drivers side panel.
View 1 RepliesMy truck is an 2003 2500hd with the 6l engine and 89k miles. From time to time I'm getting message "reduced engine power". Usually at the morning after 10-15 minutes after starting. I have to pull over, shut it off, wait few seconds then restart it. The ses light goes off usually by end of the day ( or after few hours ). When scanned by chevy tech showing code P1516 Throttle Actuator Control (TAC) Module Throttle Actuator Position Performance. I have new battery with new main cable. TAC Module was cleaned.
View 14 RepliesA friend just had a transmission line pull out of his radiator and blow fluid all over everything.
How do these lines work? Are the kind of like the fuel lines that just plug in and are held in my a retainer clip?
Does the whole radiator have to be changed to fix it or can the "fitting" be turned out of the radiator and replaced?
Looking at the line that is still in the radiator, the fitting looks like a large hex nut at the radiator with a thick rubber washer on the outside.
I am trying to get some advice on a diagnosis for a transmission problem i'm experiencing with my vehicle? It's a manual transmission and the sound i am hearing is when i shift gears is a loud whirling grinding sound. It's really loud in 2nd 3rd and 5th and doesn't stop.
View 1 RepliesI have a 98 chevy truck that won't start. After it sits. It was starting after cycling the key a few times. But now it won't start. Could it be the pump? I hear it running.
Or could it be the regulator? It was running good after it started. No check engine light, no gas smell, and no rough idle.
Truck is an extended cab, 8' box, 4x4
This truck has begun to not start in cold weather. No click of the solenoid, no starter movement. Dash lights all work, heater, wipers, etc. I put a space heater in the cab, on the drivers side floor board, warmed it up and then it would start.
The cruise control on my 2002 Chevy 1/2 ton Silverado doesn't work. Went to boneyard and bought a module but it didn't fix my issue. Borrowed a multimeter and tested the cruise control module plugin. The only pin that came up with a incorrect reading was the first brake test. It's suppose to have 12 volts with brake pedal up but showed about 30, so I changed the brake light switch. Still no cruise control.
Since I have a high reading on the brake pin, do you think I have a wire issue there or would my problem be in the multi switch wires by the steering wheel?
I have a 92 chevy truck with a 350 engine that came out of a 93 chevy my problem is my module in the distributor keeps going bad when i spoke with the previous owner of the motor he told me that he had the same problem and advised me to change the distributor. So I took my distributor out of the original motor and put in but the problem still exist, also I have noticed that I have nearly twice the exhaust coming from the drivers side tail pipe as I do the passengers side.
View 1 RepliesOn my 1999 Chevy Silverado Z71, a gurgling water sound is present everytime I accelerate. Are there any other Chevy owners that have had this same problem? If so, how was it resolved?
View 14 RepliesThe issue I'm having is the A/C. When I got the truck the A/C was completely freezing. Recently however, the compressor was having issues not engaging and I fixed that by simply plugging the cord to the accumulator thing. . Now the compressor engages, but is not cooling really at all. It is an old truck and the compressor is a little worn from what I see maybe 2mm space when not engaged. I checked the levels of freon/coolant with a gauge and the amount is perfectly fine. Plus there seems to be no leaks.
View 1 RepliesI have a 1993 Chevy Silverado, 350, 2WD. It has a 4L60E transmission. I just started having a problem shifting from 1st to 2nd. When accelerating the RPM's go way up and won't shift until I let off the throttle. Then it shifts into all other gears normally.
If I accelerate slowly. it will shift into 2nd at about 16 MPH. It will then shift into all other gears normally. I have replaced the Throttle Position Sensor, flushed the transmission and replaced the filter and fluid. This made know change in performance.
I am now suspecting that it might be the 1-2 shift solenoid. The check engine light is not on and everything else works fine.
I have a 98 Chevy truck with a 4L60E. It has no second gear. I was sitting in park for about 10 minutes with the engine running, then put it in drive and it never shifted into second. It felt like it went straight to 3rd. I played with it manually until I figured out I had reverse, 1st, 3rd, 4th and torque converter lockup, just no second gear. My acceleration rate was medium and when I reach about 27-28 mph it would shift from 1st into 3rd. It has 230K on it so I rebuilt it with all the typical parts - frictions, steels, band, sun shell etc., still no second. I then pulled the pan back off and replaced the spacer plate and put in a shift kit. While I had it down I put a corvette servo in and did an air check. It worked fine. I could feel the band tighten.
Both the 1-2 and 2-3 solenoids checked good at 23 ohms. I swapped their positions to see if it would make a difference. I also checked to make sure the 1-2 accumulator piston wasn't stuck in its bore, the spring was new from the shift kit. It was fine. Put it back together...still no second gear. When I originally pulled the pan off for the rebuild, the pan was free of any debris and was very clean. I then drove it a couple of miles to a local transmission shop. They put their scan tool on it and drove it around the block. There were no codes and the ECM was calling for second gear. It doesn't sound mechanical since almost all the parts have been replaced, rebuilt or inspected that affect the 1-2 shift. It sounds electrical. Is there anything I have missed?