Chevrolet - Venture :: 2004 - Front End Grinding Noise
Jun 24, 2016
I have an 04 Chevy Venture. Recently it started making what I can only describe as a grinding. I have been a mechanic for over 30 years, working on everything from motorcycles to heavy construction equipment. This is a new one on me. I have checked the wheel bearings, brakes and rotors, and suspension. All good. I have blocked her up and put it in gear, and the noise seems to be coming from the transaxle. Fluid is cherry red and is not burnt, no metal shavings, and not low. I have noticed that while driving, if I jog the wheel left or right, it quite until you straighten out again. If I weave back n forth going down the road, it's pretty much non existant, but the cops are starting get suspicious.
View 6 Replies
Advertisement
I have a 2004 Chevy Venture van, the front tires wore out on the inside, badly. DH adjusted the toe (made the rod shorter, so made it more toe-out?). We got new tires, after 1000 miles, they were again wearing on the inside. I convinced him to get a front end alignment. After the alignment, there is a lot of road noise, goes away when you go around a right turn. Could it just be the tires wearing differently, or is it a wheel bearing, and could that have been affected by the alignment? We have driven 150 miles since the alignment and it still is noisy.
View 11 Replies
Grinding noise in front end, replaced caliper, bearing, brakes and cv joint...
View 5 Replies
I have a Venture with a steadily-worsening vibration problem which is always worse at the front passenger side. The vibration is not the growly rumble I remember from the bad bearings I replaced 3 years ago. It's more like the thudding feel of an out-of-balance tire, but the tires are relatively new and have been rotated and balanced since purchase and since I noticed the problem. The vibration shows mainly from 45-55 mph, but not if coasting. It's only when the engine is under load that I feel it. It occurs when the gear select is in D or 3. At any other speed it is not as bad, but if I get on the gas, the vibration becomes worse. Revving the engine in park or neutral reveals no abnormal vibration.
I jacked up the van and rotated the tires again and checked for any play in the bearings or loose mounting bolts - nothing obvious there. I did notice on the passenger side of the engine, around the inboard CV joint, a spray of thick axle/moly grease, like one would find inside a CV boot, as if the boot has a small hole in it, but the CV joint does not grind or make any typical noise on sharp turn.
My list of guesses include: motor mounts, tranny mounts, bad bearing/hub, bad half shaft/CV joint, tranny going bad, bad bearing in engine.
History/details: 2004 Venture LS long wheelbase. 160,000 miles. Goodyear Viva 2 tires. Front bearings have been replaced as a set once, driver side again since then, when the ABS sensor went bad. Sometimes when I put it into drive and turn sharply to the left, traction control turns on momentarily. The tranny has begun to slip and grab on a coast-to-stop followed by sudden acceleration.
View 4 Replies
This started out as an intermittent problem after I would run the a/c for a bit. Now it happens every time I get in the van regardless of if I turn on the a/c. The engine begins acting like I am pressing the gas pedal, but not flooring it. I have to press hard on the brake in order to get the vehicle to stop because it is trying to race ahead and I don't have to press the gas until around 45 mph. What in the world is going on with my van? If I throw it in neutral it just goes nuts. I have been pulling over, shutting off the van, waiting a few minutes, and then cranking up again. It could take a couple of minutes for it to start again or it will do it right away.
View 4 Replies
My Prius has developed a disturbing noise over the past 2 weeks. I believe the noise is coming from the front, driver's side. The faster I go, the louder the noise. It begins shortly after accelerating and doesn't stop until I stop the car.
I didn't think it was a mechanical noise, but now I'm not sure. I feel a slight vibration in the accelerator pedal while the car is making the noise. I'm wondering if this is something in the axle, wheel bearing, transmission, or what.
View 6 Replies
I've got a 2004...it has 90,000 miles. For about the last 5000 miles I've been experiencing - only a few times a month, and totally out of the blue - a grinding noise coming from the front (i think left). This happens when I'm traveling at about 55-58 mph (never at lower speeds). It even happened once when the cruise was set. It gets pretty loud, and i find that if i pull over and stop for a few seconds, then keep going, that it stops. In other words, it seems that breaking to a stop disengages whatever the cause is. Also, no warning lights come on at all...like i said, it happens totally out of the blue. No, it's not the wheel bearing.
View 6 Replies
I have an '04 Corolla with 206k with a slight grinding noise from the right front when I make a left turn. Is it the outer CV joint? The noise sounds like the tire is rubbing against a splash guard but it's not.
View 3 Replies
I've had a grinding noise coming from the front passenger side, sounds like the wheel area of the car, for many months. I've driven thousands of miles on it like this, mostly because I'm broke and the car otherwise runs fine, but also because when I've taken it to mechanics, they are stumped.
I took it to a shop about a year ago and he had it for a week, had different specialists look at it and ruled out anything mechanical (wheel bearing, etc.) In the end, he threw up his hands and didn't want to give me any more free labor for his non-diagnosis, and thought he ruled out everything but the transmission. I took it to a transmission shop recently, and the guy ruled out right away that it was the transmission. He tried to diagnose the problem and was stumped too.
Here's what it is doing. It makes a grinding noise around the front passenger wheel when I accelerate. Only when I accelerate. It seems to be more active when it is cold, and after I've been driving the car for about an hour or so, it goes away. It used to only really happen when taking right-hand turns, and that is still when it is at its worst, but now it does it anytime. However--some days it is very bad and some days very light. One day--of course the day I designated to take it to the shop--it stopped altogether and drove like new. Just until I got it home. It is worse in low gears, and used to only happen in first, second and third, but now on an active day I can hear it on the interstate in fifth gear.
The shops I've taken it to can't seem to figure out what it is. Reading threads online, I've learned that people with similar problems found the problem was a bad passenger side motor mount. I have the car at a new shop right now, and I asked them to replace the motor mount, even though it looks fine. I had a long talk with the mechanic there today and he seemed a bit skeptical, but thought it was a possible solution.
Should I spend the money on a motor mount even if it looks okay? (I've also read that the Focus mounts look fine from the exterior when they are bad because they have a gel interior that busts). Especially if this doesn't work, I'm going to be back at square... um, zero.
View 3 Replies
2005 ford f150 Fx4 So last Friday I started hearing a grinding noise from the passenger side front of my truck. sounded like metal on metal. So I started rooting around and noticed that bottom ball joints were shot. so replaced bottom ball joints on both side. I aslo replaced wheel bearing hub assembly on both sides, still heard the grinding. So I noticed that both axles were slinging grease, so I replaced them on both sides.
Still heard the grinding noise. So then I removed everything from the passenger side and noticed that the locking hub actuator was grinding both axle and the wheel bearing hub. So I just got done replacing that on the passenger side, put it all back together, and still grinding noise ringtones free. Also replaced the 4wd solenoid that they said gets water in it, and I replaced the check valve. And I put new Rotors and breaks. What it could be?
View 2 Replies
I just bought 2006 f150 4wd . It make a grinding sound on both sides in the front end..it seems to be independent and when I slow and come to a stop, I makes a clanking noise like its locking something in.
View 4 Replies
I have an intermittent grinding noise coming from what sounds like both front wheels, it sounds like metal on metal almost like something metal rubbing the rotor but I just put new pads on and the noise was there before as well with nothing touching the rotors but the pads. The sound will appear out of no-where at low speeds of 35 or below and will continue until I brake and slow down, just before I come to a compete stop the noise will stop with a slight clunk.
I can then drive away with no noise. I am pretty sure it is not brake related except maybe ABS somehow but was also thinking front axle or diff, also have read posts that are bearing related, but both at the same time?. It is the slight clunk before stopping that I can not figure out is related to. It is an 05 f150 xlt 5.4 super cab 4wd with 85k miles
View 2 Replies
Ok here goes. I recently replaced the front wheel hub and upper and lower ball joints on the the driver side of my 2004 f250 CC SB 6.0 fx4. Now when I put into 4 wheel drive I get a grinding noise that sounds like a worn out break pad from that side only. It didn't do it before and it only happens in 4x4. I have replaced the wheel hubs before and it was fine. Also The needle bearing race on the axle is good.
View 2 Replies
I've got a new issue that is happening on the front end of my truck. Whenever I try turning my wheel while driving, I get this rubbing/grinding noise coming from the front of my truck. It only happens when the wheels are in motion. It seems to happen less when I'm driving at higher speeds, but I can notice it make the sound at any speed. I tried driving it slowly in an empty parking lot while turning and it's definitely making the sound every time the tires rotate.
I took it in for an alignment because this was happening every time I drove, whether it be driving straight or making a turn. Now that my alignment has been fixed, it no longer make this noise if I am driving in a straight line, so it only seems to happen when I'm turning. I had the mechanic check to see if they could reproduce the issue. The mechanic was able to hear what I hear, but when he put it on the lift at the shop, he was not able to reproduce the sound.
View 6 Replies
I owned a 99 f250 a little while ago. Just bought a 2006 crewcab F150 xlt about 2 months ago, and for the past month there has been this unusual grinding or whirring like noise coming from the front passenger side wheel.
I took it to the mechanic and he found a bad wheel bearing on drivers side and replaced it but that wasn't the issue. He could hear the noise but wasn't able to figure out what the actual issue was.
The noise only happens when my foot is on the throttle. (not when coasting) and i also just discovered that it doesn't make any noise at all when put in 4x4.
View 4 Replies
Back in December i purchased a 2003 Impala LS. It has about 103,000 miles on it now. Overall the car runs and drives great. However on very rare occasions I have noticed if I have to slam on the brakes or really break hard I hear a grinding sound. Now I have only heard it maybe 3 times in the time since buying the car and never hear anything under normal braking. I had the brakes checked and was told they didn't see anything wrong, but what might cause this grinding sound I have heard a few times?
View 6 Replies
I have a 2006 Chevy 1500 Silverado. The driver side front tire is making a grinding and clunking noise. It started yesterday afternoon and has gotten worse. When making a left turn there is a grinding/rubbing noise. When I go over a bump,rough gravel, or pot hole a horrible clunking comes from this tire. I haven't taken to a repair shop yet.
View 10 Replies
So to start at the beginning.... Traveled across Canada East to West towing 11000lb travel trailer, no problem. Have used 4x4 in a few campsites to pull out of a pitch without spinning the wheels and causing damage to the site when it has been really wet. All good.
Got to Banff in December and the town was an Ice rink, engaged 4x4 and all good. Crossed the Rockies and the 4x4 starts making grinding noises. Up and down some mountains and squeaking, grinding noise then clunking.
I have manual hubs, disengage and the noise all goes away. Engage 1 hub and no noise. Engage both hubs, noise back.
I bought some needle bearings and went to swap them. Got hubs apart and they look good. No scoring on the drive shafts. They are not dry, but as I have them open, repack them with grease anyway.
Do more research... Remove ABS sensor and repack main bearings with grease. (broke one sensor pulling it out, too cold plastic brittle oops). Still clunking noises.
The universal joints look good, doesn't appear to be any play in them. However, the axle seal (knuckle seal) (F81Z-3254-CB) does move around a lot in it's metal casing. It is tight on the shaft, but with the hub off, I can move it in and out, and move it side to side. If I had ESOF hubs I guess they would not be locking as I'm sure there would be no vacuum in there!
Question is then, would this seal be allowing the universal joint to wobble under load in 4x4 mode? Would this wobble be the cause of the rumble? As it is labelled as a seal and not a bearing, I wouldn't of thought this would have been a loaded point, and the weight would have been taken by the associated bearings and it could be run without this seal? But if it is not this, then I'm still looking for a clue as to what is making the rumble....
View 3 Replies
I have a 2003 Impala. Over the past couple of months I have had an occurance every so often, very random with my front driver side brake. In both rain and dry conditions, braking hard and just slowing to break I will hear what sounds like grinding when I brake, like you do when the pads are gone. Well, I have had the car in and the pads and rotor are fine, the place I took it to even test drove it and tried but couldn't get the sound. I posted here a while back on this issue and the view was that it might be the ABS, but when this occurs the ABS light doesn't come on and the sound is just coming from the driver side front. What my next move should be?
View 7 Replies
2000 Venture short wheelbase 122k miles. Original owner from brand new. Has had fuel pump replaced at 40K, intake manifold replaced and full trans (torque converter inclusive) flush, plugs and wires at 75K. (2005) All fluids checked regularly.
Recent problem. Noticed a "grinding/buzzing" sound when traveling above 25 mph. Sound is commensurate with veh speed (not engine speed). If I turn the wheel ever so slightly to the right, the sound "deepens"/gets louder), and I can feel the buzzing in the steering wheel. When I release from turning right, or turn left, the buzzing greatly decreases (though I still hear it), and I can no longer feel it in the steering wheel. I only feel it when I turn the wheel to the right, even just a few degrees.
My thoughts on the culprit (in no particular order): Wheel bearing, Transaxle/final drive (differential). ???????
Wheel bearings: No work done on front wheels/hubs. I did rotors and brake pads in April 2009 (115K). Visual inspection of all of the under car and front end. Nothing appeared out of the ordinary.
Transaxle/Diffierential: Who knows? I have had other vehicles with a normal differential/rear end, that had a bad bearing and I could usually tell which side, just by driving/turning Usually it was an outer bearing (wheel), not an axle bearing (diff).
Observations:
1..Periodically over the last 2-3 years or so, I have had to add about a 8-12 oz of coolant to the overflow every 8 mos or so. I don't know where it goes. I presume it is evaporating somewhere or VERY slowly leaking. Nothing external that can be visually noticed.
2.. Last week I checked the trans fluid. Was off the stick. Had to add 3 qts Dexron VI to bring it to full mark on stick. First two qts. barely registered on the stick. Prior to that last check was at 118k (5 k ago) and June of 2009. My written notes at the time mention "Normal. Didn't smell or look burnt, and no particulate matter in the fluid". Has been a week and the fluid level is still holding fine. Where did the 3 quarts go ???
3.. Opened radiator cap. No sludge or "strawberry milkshake" evidence of trans fluid. Looks fairly clear and orange. About what I would expect for a veh of this age and mileage. All lines to and from trans and radiator look ok. No evidence of leaking ANYWHERE.
4.. Runs an normal temps throughout the year
5.. Shifts fine with no slipping, clunking, grinding (during shifting).
6.. Overall vehicle runs, shifts, handles, and stops well.
7.. Every few weeks the ABS light comes on and then goes out after the next start.
If it's a wheel bearing (and I am leaning that way) How can I determine which side I need to replace? If I turn right, I "load" the left one. Noise gets louder. If I turn left, I "load" the right one. Given the above symptoms should I presume the left one?
View 9 Replies
Year: 1999Make: Chevrolet
Model: Silverado 1500 LS
Issue: Bad Transfer Case
Late model 99 Chevrolet Sliverado 4x4 with push button transfer case. At the end of last winter the transfer case began a grinding-noise when attempting to go from 2H to 4H.
I have a great mechanic who has proven both his skill and honesty to me a few times now. I took the truck in for diagnosis. His hope was that the electronic transfer may be faulty but unfortunately found metal shavings when he went to check the lubricant in the transfer case.
Diagnosis: Bad Transfer Case - Replacement necessary.
Mechanic has recommended a salvaged transfer case from reputable salvage dealer.
I have sourced a rebuilt transfer case with manufacturer warranties from a "major parts chain" for approximately 1/3 more cost.
My debate: The truck (while very late model), has a rebuilt engine that has less than 50k miles on the rebuild. I have expectations that I will continue to drive and maintain this truck for a very long time.
Although I am always aligned with less cost, my first response is that the rebuild from "major parts chain" is warrantied and far less likely to require a replacement in the remaining life of the vehicle.
However I am also uncertain how to evaluate the existing transmission. Presumably it has >100k. Is there a risk in pairing an OEM rebuilt transfer case with a transmission this old?
View 3 Replies
