Rhe problem is that both sides blink fast the left one used to blink normally sometimes and fast again. All the light bulbs work and are not led. I found the problem on the right side : in the front the side light blinks but the drl doesn't blink with it. Now both sides blink fast. What part of the car i should check ?
View 3 RepliesThe problem is that both sides blink fast the left one used to blink normally sometimes and fast again all the lightbulbs work and are not led i found the problem on the right side : in the front the side light blinks but the drl doesnt blink with it now both sides blink fast. What my problems might be? What part of the car i should check ?
View 3 RepliesI have a 2002 (not 2001) Chevy Venture and recently replaced the left rear (drivers side) tail light circuit board. I replaced it with a genuine GM part, and when I connected the wire harness to the circuit board and screwed the tail light assembly back in place, everything works properly for say a half hour or so, then I usually get the fast blinking left turn signal (like a bulb is out). Also, both turn signals come on solid when I hit the brake. A lot of times, if I turn off the ignition and turn it back on, I'll get the Service Traction System warning and Traction Off lights in the dash. If I take the assembly apart and push down on the wire harness and put it back together, everything works well for a short time again, but it usually reverts back to the above. It seems to be a loose connection and I thought about some kind of loctite to keep everything in place. Someone also casually mentioned a dielectric grease, which sounds like it would be better.
View 8 RepliesMy 2001 Chevy Venture van is accelerating on it's own and is now overheating. The heater works, the AC works but the defrost doesn't. I can be at a dead stop, put it in drive and it starts going on it's own, even up a hill. It's also developed a 'knock' or 'jump' with it automatically shits gears. I simply cannot afford a new engine, we did that last year when it overheated and blew the gaskets.
View 2 RepliesI have a 2001 chevy venture (254,000 miles) that has me baffled. It has been a great van but it started about a month ago sputtering and bucking and numerous times shutting off. Most times the engine light would NOT come on. It would get the hiccoughs and start bucking like someone learning to drive a stick shift for the first time. Once it sputtered hard enough to throw off the serpentine belt. I put a new timing belt on it last year when I redone the intake manifold gasket. Now its not shutting off but it has only about half the power it should and the engine light is starting to come on more often.
It bogs down and then it will try to go then bog down again. The engine light blinks for about 20 seconds then stops and goes out. When the engine light is on and stays on the code most often says system too lean, and a egr flow insufficient. It does have a vacuum leak in the hose going to the egr. Have ordered that, hasn't come in yet. Gas mileage is horrible. I have done new plugs, fuel filter and cleaned the K&N air filter. Someone suggested the catalytic converter. I dumped in a bottle of 'Cata-cleanse' from Autozone. No difference. A friend of mine had a venture doing the exact same thing. It was in the shop for 6mo with no luck. But his straightened out on its own and is running good now. I really don't feel like waiting 6mo to see if this will straighten out.
My 2001 Chevy Venture stalls after driving it approximately 15 minutes and won't start for about 20-30 minutes, then same problem occurs. I've had the following parts replaced to date, with no success.
AIR FILTER
ENGINE CONTROL SYSTEM
IGNITION MODULE
FUEL PUMP AND WIRING
2001 Chevy Venture: Pins to 2nd fan in 4 pin connector burned and melting to connector. Fan seemed to work when wiggling connector. Bypassed connector and now does not work unless A/C is turned on Full Speed. Is connector important? What controls fans? Computer controlled? Seems to be larger gauge wire in one side than the other.
View 2 RepliesAs i kid i hated seeing people make there turn signals blink faster but know as i got older I like it, so on my 2011 camry and i want to make the turn signals blink faster. Not too fast but a little faster. I know I need a flasher but i can't find one for the Camry. I know I have to remove the instrument cluster.
View 14 Replies2004 Prius here. The turn signals and hazard lights stopped working a few days ago. I found a disconnection in the grounding and repaired it. Also replaced the fuse and the flasher switch. Now the lights work, and I can hear the flasher switch clicking, but they don't blink!
View 13 RepliesNo B5 posts since the variant has been running well....'til today, when I noticed irregular turn signal operations. This is for a B5.5, 2002. Occasionally they'd work as they should, but much of the time they'd blink a few times then stay off.
Continues to happen after shutting down the engine and restarting (was wondering if that would reset anything). I recall some sort of relay problem with the turn signals. Does this sound like what's going on?
Car is 2000 Corolla with 58k miles. Today, I had my hazard signals on while parked when suddenly....they stopped blinking. The signal lights in the dash just stay on...they do not blink. I also verified that both front and rear lights also turns on...it just doesn't blink.
The corolla has a fuse box under the hood in the drivers side. Here is the schematic for the fusebox: [URL] .....
From what little I know about mechanics/electricity, can I just pull the wiper fuse and put it into the turn signal fuse while I wait for a new fuse? Do I need to disconnect the battery?
How to confirm this is the part I'm suppose to install: [URL] ....
2005 explorer just started having a fast blink on the right turn signal. Left turn and hazards work fine.
View 3 RepliesHow to make the 2012 Camry SEV6 turn signals do the little 3 blink for changing lanes, llike the newer ones, or the corollas do... Is it impossible???
View 14 RepliesJust installed e-codes in my car about a week or so ago.. When I did, the blinkers started to blink very fast. All the bulbs work fine and everything, and the hazards blink normally as well. Does this normally happen?
View 7 RepliesI have checked all fuses, checked wires on top of steering column all checked out ok. Hazards work but when I press brake tail lights just blink with no brake light but the 3rd brake light works??? Signal switch maybe??
View 14 RepliesI did my research and it turns out I need a relay switch for my blinkers. these bulbs are bright but flash too fast..
How do the relay switches work, what do i plug them into and do I need one relay switch per blinker?
I made the conversion of the regular bulbs to led ( stops, position, turn signals ) but I have fast blinking in turn signals. I know that the led has fewer electric resistance than the regular bulbs so the car takes this like a damaged bulb.
I know two possibilities:
1- A resistance for each one of the led to confuse the system.
2 - Changing the electronic relay
I don't know which one is better. I need a resistance for each bulb? which relay is the appropriate one for this car (there's a lot of references on the internet and I can't find the relay in the hood's car).
I have a 1998 or 1997 Honda Accord and just noticed the other day that my left turn signal was blinking faster than normal. Now I know that this would denote a burnt lightbulb but I got out of my car to see if one wasn't working on my left side. All of my lights seem to be "on" but the left side turn signals are flashing faster than normal. Also I did hit a speed bump at app. 40 mph the other day.
View 4 RepliesMy '99 F150 is having wiring issues. It started with a left flasher being fast and the rear bulb not working. I put in new bulb and that didn't fix it. Then I realized that I also had no tail lights. The reverse lights are good and the brake lights work too.
So far I have searched for and repaired suspicious splices done by PO, added a ground wire that was cut off from the trailer wiring harness, checked every fuse that I could with an ohmmeter and I pulled the multi function switch and tested it with an ohmmeter also. It tested fine but I did find one of the female pin connectors had pulled out of the harness. I managed to get it back in and seemed to click into place alright. Somewhere over the course of all that I now have both sides of my flashers fast and still no tail lights. Good news is that I haven't broken my brake lights or reverse lights yet.
Could I have a bad flasher relay? Earlier in the process I did have my 4 way flashers working correctly and a couple times I even had the turn signals going. Now, none of the rear blinking lights work but the front ones go 90 to nothing and I still have no tail lights. My truck does have the auto lamp thing.
I have a 2001 Chevy Malibu ,I have noticed a whirling sound coming from my steering wheel whenever I am turning. I am wondering what could be the cause and should I get it checked out.
View 6 RepliesMy 2002 chevy venture does not provide any heat from the cabin air system..The engine reaches proper driving temperature normally.Can't heat the cabin or get any modulation of cabin temp when using A/C.
View 2 Replies