My 2001 Chevy Venture stalls after driving it approximately 15 minutes and won't start for about 20-30 minutes, then same problem occurs. I've had the following parts replaced to date, with no success.
AIR FILTER
ENGINE CONTROL SYSTEM
IGNITION MODULE
FUEL PUMP AND WIRING
I have a 1991 Chevy Lumina and I believe this wire is the root of my problems. I
wasn't the one who unplugged it but it seems it was unplugged as an easy way to get around a problem. When unplugged the car runs but the performance is off, It doesn't feel like it has the same power as it does when it's plugged in and it also sounds different when in idle. When the wire is plugged in the car stalls while driving at random intervals between 1 and 10 minutes and needs to be jumped to start it back up. I will attach pictures of the wire and its location within the surrounding area.
My 2001 Chev Silverado 1500, 5.3L, 260,000 K miles may finally be near the end - It has been running great until this week. I live in Portland - weather was down to about 10 deg F a few nights and when it warmed up again the trouble started. After starting cold and driving for about 15 minutes it starts stalling out.
Sometimes it will fire right up again and I'll hardly notice except for a momentary drop to 0 on the tach. Other times I'll have to pull off to the side to the road and restart it. However, 2 times now it would not restart and stay running. It would either fire up but then die within 10 seconds, or it would just crank. Both those times it did restart successfully after 40 minutes had passed total and it drove fine afterwards until I got where I finished my commute (about another 5-10 minutes of driving).
I took it to a mechanic who could see it stall but was not able to duplicate the 40 minutes out of commission thing. His fuel pressure gauge indicated that the pressure was fine during the stall outs. The mechanic ran the computer diagnostics but didn't see anything unusual. He wasn't really sure what the problem was. He recommended replacing the fuel pump and fuel filter anyways - but couldn't say if that would make any difference.
Should I start throwing money into new parts or move on and start looking for a new vehicle?
I have a 1999 Venture Van. The engine has a low idle and stalls when stopped/parked after driving on the highway for 10 minutes or longer. Whenever I drive it to the train station in the morning to go to work, it dies as soon as I park it. It will start up again fine right away tho. I drive 10 minutes on the highway.
The engine light is on, but goes off sometimes for months before coming on again. I've brought it to at least 3 mechanics and they can't get the light to stay permanently off, and say to just drive as-is. But that still leaves me with the low idling problem. It doesn't always stall, but the potential is always there, as you can hear the low rpms threatening, and dread stopping at a light.
I had the engine light interpreted as P0122 TP SENSOR CIRCUIT LOW. The mechanic replaced the Throttle Positioning Sensor. Engine light came on again 2010. Mechanic did a Computer system check/smoke test. Diagnosed a Leak in evap system so they installed a new gas cap and vent valve. 2 months later, engine light went on again.
New plugs, spark wires, fuel filter, fuel treatment, fuel line, gas cap, vent valve.
1 month later light is on again, and low idling persists. I put alot of $ into the problem with no solution. Some mechanics say the engine light has no relation to the low idling.
Wife wants me to get rid of it, but the Van is in great condition except the low idling/stalling problem. I don't care if the light stays on, as long as the low idling/stalling stops. Can't I just ask a mechanic to increase the idling rpm?
My 04 Chevy Venture has started smelling of gas when I drive. It doesn’t happen all the time. I can drive to a destination and smell nothing, park, and a few moments later leave and smell the gas. I have had the fuel lines checked and was told there are no leaks. The smell is stronger when I have the vents pointed at me, but if I switch to the floor vents, it diminishes.
View 5 RepliesMy 2001 Chevy Venture van is accelerating on it's own and is now overheating. The heater works, the AC works but the defrost doesn't. I can be at a dead stop, put it in drive and it starts going on it's own, even up a hill. It's also developed a 'knock' or 'jump' with it automatically shits gears. I simply cannot afford a new engine, we did that last year when it overheated and blew the gaskets.
View 2 RepliesMy 2005 Chevy Impala is taking a long time to crank. Now after 10 minutes or so of either idiling or driving, the car stalls out. I am able to restart it. Replaced the battery and no change. Lights are not getting dim in any way so I figure it's not the alternator. Could it be a bad starter?
View 2 RepliesI have a 2001 chevy venture (254,000 miles) that has me baffled. It has been a great van but it started about a month ago sputtering and bucking and numerous times shutting off. Most times the engine light would NOT come on. It would get the hiccoughs and start bucking like someone learning to drive a stick shift for the first time. Once it sputtered hard enough to throw off the serpentine belt. I put a new timing belt on it last year when I redone the intake manifold gasket. Now its not shutting off but it has only about half the power it should and the engine light is starting to come on more often.
It bogs down and then it will try to go then bog down again. The engine light blinks for about 20 seconds then stops and goes out. When the engine light is on and stays on the code most often says system too lean, and a egr flow insufficient. It does have a vacuum leak in the hose going to the egr. Have ordered that, hasn't come in yet. Gas mileage is horrible. I have done new plugs, fuel filter and cleaned the K&N air filter. Someone suggested the catalytic converter. I dumped in a bottle of 'Cata-cleanse' from Autozone. No difference. A friend of mine had a venture doing the exact same thing. It was in the shop for 6mo with no luck. But his straightened out on its own and is running good now. I really don't feel like waiting 6mo to see if this will straighten out.
Rhe problem is that both sides blink fast the left one used to blink normally sometimes and fast again. All the light bulbs work and are not led. I found the problem on the right side : in the front the side light blinks but the drl doesn't blink with it. Now both sides blink fast. What part of the car i should check ?
View 3 Replies2001 Chevy Venture: Pins to 2nd fan in 4 pin connector burned and melting to connector. Fan seemed to work when wiggling connector. Bypassed connector and now does not work unless A/C is turned on Full Speed. Is connector important? What controls fans? Computer controlled? Seems to be larger gauge wire in one side than the other.
View 2 RepliesThe problem is that both sides blink fast the left one used to blink normally sometimes and fast again all the lightbulbs work and are not led i found the problem on the right side : in the front the side light blinks but the drl doesnt blink with it now both sides blink fast. What my problems might be? What part of the car i should check ?
View 3 RepliesMy 1989 Honda Accord LX, with 135,000 miles on it, stalls after a few minutes of driving. Then, after re-starting, it stalls before I even have a chance to put it into drive. My mechanic replaced an electric base plate gasket in the carburetor but warned me that this repair might not fix the problem. If it didn't, I probably would need to replace the carburetor -- if one could be found for a 1989 model. Well, I still have the problem. My question: Is it worth it to invest $1,500, more or less, for a carburetor for a 22-year-old car? I've been using it strictly as a second car for the last 11 or 12 years. It seems to be in good shape otherwise.
View 2 RepliesI'm really bad with cars but I'll try to be as specific as possible.
Car: 2002 VW Jetta
Basically the car will just stall out of nowhere while driving (not stopped at a light), I would say usually about 10-20 minutes after I started driving. After this, when I try to start it, it makes that noise like it is trying to start but the actual ignition doesn't happen. it usually takes me about 15 minutes to start it up again.
In addition to this, when driving, the RPM seems to randomly drop off often, and the car also jerks frequently, especially when I press on the pedal quickly.
I have a 98 Sebring Convertible 2.5L V6 that stalls after 10 minutes of driving at 30mph or even at highway speeds (ouch), but it seems only if the car has been sitting parked for 5 days will the stall occur. If I drive it daily/every other day, she seems to run just fine. Somewhere in between 2 and 5 days, there is sometimes a surge at that distance, but not a complete stall. The stall has been a very specific distance that if I let the car sit for 5 days, I can essentially pull over in anticipation of the stall. When the car stalls, the dash gauges all go to 0 and lose all power steering, but headlights stay on. Otherwise, there's been no noticeable loss of power, rough idle or anything else to indicate a problem. There are no codes on the computer. The stall happens once. I can pull over and immediately restart my car and be on my way without experiencing another problem until I let the car sit for 5 days again.
View 2 RepliesMy 96 Buick Regal acts like it is out of gas after driving for about 10 min. Takes awhile to start, then runs rough if at all. After it sits, it runs fine again for about 10 min. I changed fuel filter, fuel pressure sensor and fuel pressure regulator.
View 4 RepliesI have a "56 thunderbird with a mid-60"s ford 390 engine w/ 4 bbl holley. I just had engine completely rebuilt and everything else is new: carb, distributor, electric fuel pump, fuel tank, etc.
Problem: car stalls and dies after a few minutes of driving. Generally restarts after waiting about a half hour, but not always. I have a fuel filter with clear bowl in fuel line just ahead of carb. The bowl is usually about 2/3 full of fuel, but general appears empty when the car stalls.
After waiting a while, the bowl refills and the car restarts.
1999 Accord, 110k mi., stalls while driving or stopped a few times a week, then takes a couple of minutes to turn over. Mechanic replaced or cleaned main relay, fuel pump, and ignition module. Could sell it but recently rebuilt tranny and replaced timing belt. Mechanic is stumped.
View 7 RepliesHave a '92 Olds Cutlass Ciera 6 cyl 3300 engine. After 20-30 mins of driving it dies when I have to stop for a light. Depressing the brake kills the engine. Starts right up after but as soon as I put it in drive, it dies. If the car sits for 20 mins or so after problem begins it's okay. If I get to an intersection and have to stop, I put it in neutral. When I have to go again I rev the engine, let it die down some and then put it in drive (hard on the car, I know, but it's only way to get going again. Once I'm moving, I can accelerate and it's okay. What is wrong with my car?
View 3 RepliesI have a 2010 F150 SCREW with 4.6l 3v 4wd. Up to 100,000 miles nothing more than tires, brakes, and evap purge valve (50,000 miles). Check engine light came on right around 100,000 miles and had no driving problems other than some crappy fuel mileage. Did the following:
Changed evap purge valve, reset cpu by unplugging. CEL came back on after about 200 miles
Took the truck to a shop to get oil change, change plugs, diff fluids, transfer case fluid and get CEL looked at. Shop recommended changing intake gasket as you could see gummy type fluid on passenger side valve cover. When removing the intake found the intake cracked, changed gasket and intake. They reset the light. 200 to 250 miles later the CEL came back on.
Took it back to the same shop, left it with them for the weekend. they think it could be the O2 sensors. I went out and got the shop all 4 O2 sensors and they installed for free (seeing as I spent $2500 with them for all the previous weekends work) 200 to 250 miles CEL came back on
Determined to find time to have another shop look at the problem and trying to get it to a family friend, wasted about a month. At the end of February stopped at a friends house after being there for 20 minutes tried to start truck, it wouldn't fire. It would crank but no fire. Called for a tow and while waiting tried to crank the truck and it fired up, like nothing was wrong. Cancelled the tow truck and drove right to dealership. They determined it was the MAF sensor. Spent the $500 to have them diagnose and change MAF. All things good for about a month and about 3000 miles...
Now in the past 2 weeks it has done the following: I am a construction manager so i am in and out of my truck all day so the engine is never really a cold start except for the mornings when driving to work, it stalled while leaving work on a Friday at low speed. luckily I was able to pull in to a gas station. Tried to restart and it cranked but no fire. after 5 minutes or so tried again, fired up drove home the 35 miles with no problem, truck had power, smooth idle. No CEL.
Same weekend on Sunday, coming home from church at highway speed truck got sluggish, wrench light came on, no response to throttle. Rolled to a stop and then the oil light came on and chime from dash. Turned the key all the way off waited 10 seconds, again crank but no start. Waited 5 minutes and it fired up no problem. Church is only 3 or 4 miles away, no problem going to church, 2 miles into the trip home is when it stalled.
Drove all week, 500 plus miles without a stall or problem
Coming home on Saturday from my kids soccer game again 4 or 5 miles away (no problem going to game) truck stalled at highway speed. Coast to a stop, wrench comes on and then oil light, chimes from dash. Turn key off, wrench and oil light do not come back on. Try to start, again crank but no fire. waited the 5 minutes or so and it fired up fine. (Earlier in the day i got gas, 87 octane, from a one of my regular gas stations from 1/4 tank to full)
Today coming home from church but running an errant the truck stalls after making a left turn about 3 miles from the church at low speed.
All of this without a CEL. What can solve this problem. Clean a sensor? clean throttle body? Gas tank additives? I am due for an oil change and may ask the dealer to look at it but its going to be time consuming as I cant radially repeat the problem and there is no CEL. As I am thinking about the different times it stalled, other than the first time I was probably around 1900 to 2300 rpm.
My truck starts and runs fine cold. after 10 minutes or so of driving, it starts choking and stalls. If you try to start it, it will not. If you wait about 3 minutes, it is fine, starts , and drives ok, for about 3 minutes. I have replaced, plugs, fuel filter, battery, and a ignition module, as well as cleaned the opening of the throttle body
Ford has ordered a fuel pump, I am thinking it could be the
-Throttle position Sensor?
-MAF sensor?
-fuel pump?
It puts out code p0191 for low fuel pressure. Ford is scheduled to install new pump in am, but I don't want to spend a grand if it is just the TPS or MAf?
drives nice for mile or 2, stalls. turns and turns for 10 minutes, then starts. drives great for mile or 2, stalls. wait 10 minutes, starts. repeat, repeat!!
View 1 Replies