Chevrolet - Transmissions - Montecarlo :: 1996 - Grinding Noise In Front End
Feb 1, 2015
Grinding noise in front end, replaced caliper, bearing, brakes and cv joint...
View 5 Replies
Feb 1, 2015
Advertisement
Chevrolet - Transmissions - Montecarlo :: 2002 - Hard To Shift Between Gears
I own a 2002 Monte Carlo SS 3.8 6cyl. I believe it has a 4T65-E transmission.
On a regular basis if I drive 20 miles out of town, on my way back the transmission starts to shift hard (long shift?). From my research online, the 4T65-e is a faulty transmission to begin with. Is it worth replacing the Shift and Pressure solenoids? If I were to buy a new transmission where should I look? What are some model numbers?
Oil, trans fluid, filters are changed on regular basis.New catalytic converter. No Check Engine Light.
Chevrolet - Tahoe :: 1996 - Lock Or Seize During Cranking / Slight Grinding Noise When Normally Starting
Have a 1996 Chevy Tahoe (305) Engine having engine cranking problems. It makes a slight grinding noise when normally starting. But sometimes it the noise is loud and seems to lock or seize during cranking. I tried shimming it without success, the gear even stuck in the flywheel. I had the starter rebuilt when the bendix stopped engaging the flywheel. I bought this PU second hand and the flywheel cover had been removed as if this truck has had existing starter problems. Also the flywheel teeth look ok.
View 3 RepliesHonda - Accord :: 1996 - Grinding Noise On The Front Driver Side
I have a 1996 Honda Accord (automatic) with just over 149,000 miles. In the 5 years since I've owned it it's required little more than some new spark plugs and tune up. I currently drive about 30 miles a week, but starting tomorrow I'll be driving much, much more to a new job. Living in Chicago with awful potholes, salt, and traffic, I'm concerned about what may happen in the near future...
I've been getting a grinding noise on the front driver side for years and have never fixed it and never noticed a change...I know it's the tie rod ends/ball joints. I've been warned that the wheel could come off, and as much as I believe them and don't want this to happen, nothing has ever happened. Is this something to do since there has been no change in symptoms or car performance in a couple years?
Other than that, any tips for keeping the car in good, working order? I do oil changes, but are they really necessary every 3000 miles? I have to make it last as long as possible and actually love the car anyway!
Chevrolet - Montecarlo :: 2006 - Ticking Noise Coming From A/C?
I have a noise coming from the interior of my car that is incredibly, amazingly, terribly obnoxious. Not to mention somewhat embarrassing when I have a passenger, and it decides to show off.
Part of the problem is that it's unpredictable when it will occur. It could go weeks or even months without making the noise. Out of nowhere, it will start up again and continue once or twice day, or even any time I start the engine.
The best way I can describe it is: TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK
A brief pause of maybe 5 seconds....Then: TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK-TUK
If I switch the blowing knob from the driver setting to, say, feet, or dash, it'll stop for a moment and then resume with the TUK-TUK-TUK-TUK-TUK
After it gets as many TUK-TUK-TUK-TUK-TUKs out of its system as possible, everything goes back to normal. During this process and afterwards, it blows cool/hot air at the correct setting, so no performance issues.
Car in question is a 2006 Monte Carlo - Any possibility this is a relatively simple DIY repair? I'm comfortable with basic tasks like replacing car stereos, speakers, headlights, oil change...If this'll require much more skill than those sorts of tasks, I'll likely need to put this repair in the hands of a professional.
Chevrolet - Venture :: 2004 - Front End Grinding Noise
I have an 04 Chevy Venture. Recently it started making what I can only describe as a grinding. I have been a mechanic for over 30 years, working on everything from motorcycles to heavy construction equipment. This is a new one on me. I have checked the wheel bearings, brakes and rotors, and suspension. All good. I have blocked her up and put it in gear, and the noise seems to be coming from the transaxle. Fluid is cherry red and is not burnt, no metal shavings, and not low. I have noticed that while driving, if I jog the wheel left or right, it quite until you straighten out again. If I weave back n forth going down the road, it's pretty much non existant, but the cops are starting get suspicious.
View 6 RepliesFord - Explorer :: 1996 - Grinding / Rattling Type Noise From Front Driver Side At Low Speeds
I have a 1996 Ford Explorer (4WD model). Approximately 4 months ago I had a new set of tires put on it, and in the process of replacing the tires the shop noticed that I had a bad ball joint and one of my wheel bearings was going bad. They said the ball joints were known for completely failing, but the wheel bearings usually didn't, so they recommended that the ball joint be replaced first. That is what I had them do. I haven't had the money to get the wheel bearing replaced yet. This past week it got worse to the point where I can hear it now.
At low speeds I can hear a grinding/rattling-type noise from the front drivers side (that's the side that has the bad wheel bearing). At higher speeds the grinding/rattling-type noise fades away due to road noise, but I can still hear a humming-type of noise that is a bit loader than normal - this noise just started a couple of weeks ago so I'm suspecting that this might also be related to the bad bearing.
I won't have the money to get this fixed for another 2 weeks. In order for me to have the money in 2 weeks I will need to continue working at my job 2 days a week. It's approximately 2 hours round-trip from my home to my job. Obviously with the bearing sounding significantly worse I don't want to drive it any more than I have to, but the only way I can get the money to fix it is to keep driving it back and forth to work.
Here's my question. What risks am I running by continuing to drive this? Am I running the risk of the wheel falling off while I'm driving down the freeway at 70 mph? Am I likely to experience other damaged parts in that area of the vehicle?
Chevrolet - Montecarlo :: 2000 - Dim Car / Fog Horn Combo Noise While Idling In Parking Spot
My poor 2000 Chevy Monte Carlo SS is turning into a hooptie. Or at least it sounds like one. I am due for a front brake pad change in about a month, so I'm wondering if this new noise has anything to do with it. If not, I certainly hope it's affordable!
And now to the strange noise being emitted from the front of the car. This morning, about 50 degrees, I started my engine to drop my boyfriend off at work. While idling in the parking spot, I heard a dim car horn - fog horn combo noise. A neighbor gave me a "wtf" face, and I'm sure I returned her stare with the same expression. Hoping it was something else, I drove off.
First stop light, just down the block, while idling and waiting for the light to turn green, I hear the same noise. Very embarrassing. Next light I stop at, same noise. Once the car got to half of its optimum temperature, the noise stopped and didn't return.
That is, until several hours later when I needed to go to work and restarted the car from a cool nap. Same noise.
So, what the deal is? I thought it might be fan related, as it kind of sounds like there is some rattling going on in there, too.
Transmissions :: 1995 - Chevy Rear End Differential Grinding Noise
I bought this van (1995 chevy van 20) last year and the rear end made some sounds but not as bad as its now.
So, after buying it I decided to open up the rear end and inspect for any damage to suggest it needs repairs. No signs of metal chips, nicks, or any wear on the bearings and gears. After a while of driving it I decided to remove the carriage and pinion from the rear end to give it a close inspection. After doing this and finding no clear sign of war or damage, i decided to replace the carriage barrings to see if that made a difference. After placing the new bearings back on the carriage, pinion back into the rear differential, and trying to do it all by myself, i lost the marks i had placed on the carriage bolts and clamps since I had little time to get it back together.
After that I had no other choice but to place the clamps bolts where i could estimate they belong. I was done, then drove it and some of the noise went away but a grinding sound on decelerating emerged. Well, now that sound is gotten worst and its more like a grinding sound. I can assume that not placing back the bolts and carriage clamps back changed the position of the carriage relative to where it was, but am not 100% sure. how can I correct the positioning of the carriage? if that is not the issue what test can i perform to find the culprit?
Chevrolet - Tahoe - Transmissions :: 2004 - Front End Of Car Started To Shutter While Driving
I have an '04 chevy tahoe, only 70k. Very recently the front end of the car has started to shutter while driving. This happens when I am going generally above 45mph- more so going up a hill. It feels a little bit like I am driving over unevenness/ripples in the road- even when it's smooth flat pavement. When I take my foot off the accelerator and just coast the vibration stops. I got new tires put on front so it is not a wheel balance issue. The car does not pull left or right either like out of alignment. And the engine rmp's do not fluctuate/strain when the shuttering starts.
View 5 RepliesChevrolet - Montecarlo :: 1995 - Won't Start Intermittently
i own a 95 monte carlo z34. ever since i bought it last yr. i have had starting problems. i thought it might be a fuse, checked them all and there fine. i noticed when i pluged in the 2 ingnition fuses back in the fuse block under the hood,the security light lit up for a min then went out. now my car has the chip in the key also. i thought the securty system is failing some how. might it be the tumbler in the colum? if so i read here it could be bypassed, by buying a resister, and spliceing in to a fat orange wire under the steering column, to by pass the security system. is it that easy? if the person who posted the ad with the same problems im haveing could give me more detail instructions on doing this my self,because id rather fix it than take it to a dealer and spend big bucks i don't have.
View 4 RepliesChevrolet - Montecarlo :: 2000 - Random Pop When Going Into Gear
I have a 2000 Chevy Monte Carlo SS with 120,XXX miles on it. For the past year, I've been hearing a very loud POP or KNOCK when I put the car in reverse from park. Here are the details that make it so vexing.
• It only happens first thing in the morning. For the rest of the day, there is no pop.
• It only happens in cooler weather (less than 50°.)
• The sound comes from different places each time. Sometimes it sounds like it's in my rear passenger wheel well. Sometimes from the front of the car. Sometimes from directly beneath the driver seat.
• Rarely, there will be times when I'm driving and I "goose" on the gas, there will be a light pop sound. (when in drive)
I've had all of the motor mounts replaced (per mechanics opinion) and the problem persisted. My mechanic suggested it might also be transmission mounts but he doesn't know without actually replacing them. From visual inspection, he didn't see anything suspicious. Since the car is probably near the end of its life, I didn't want to spend a lot (more) on something that might not even be the problem. I asked if it was safe to drive and he said yes. I have noticed that when I put my car in reverse each morning and hear the pop, it seems to jar the car rather violently.
Subaru - Legacy :: 1996 - Grinding From Front Wheels When Turning At Slow Speed?
i have a Subaru legacy rs 1996 twin turbo, about 6 months ago now i replaced both front outer CV joints and boots due to a grinding when turning at slow speed e.g a car park. the grinding had gone and its was all fine until now the same grinding as come back. its it normal for the CV joint to wear out that fast or could there be a different problem?
View 5 RepliesChevrolet - Montecarlo :: 2001 - Revving In Idle / Chugging Along
I have a 2001 Monte Carlo that I absolutely love. The check engine light has been on forever, despite repairs that should have turned that light off. Just recently, my car has started to gain RMP while I'm stopped or going anywhere between 0-25 miles per hour. This also makes the car physically shake and jolt. Very unfortunate. I turn it on to drive once more and then my check engine light flashed and beeped at me. I thought about waiting to take it in until Monday, but now I think it is best to bring it in now.
View 4 RepliesChevrolet - Montecarlo :: 2003 - High RPM Random Misfire
Here's the deal with this car i just did head gasket, valve job, all new intake gaskets and spark plugs. Car idles fine and mid throttles fine but with high throttle it wont shift and flashes the random misfire light p0300 it seems to run out of power. I've heard everything from maf sensors to ignition coils and wires. i was just wonder a good place to start and good test to do. I have most testing equipment including scan tool so i can ride with it. o and all cylinders compression tested above 150.....
View 13 RepliesChevrolet - Montecarlo :: 2000 - Heater / Blower Only Works Sometimes
2000 Chevy Monte Carlo... The heater/blower only works sometimes, usually not at all when it's freezing out. when it's a little warmer out, it tends to work more often, but still not all the time. what could this be? my husband tried replacing the blower motor, but that didn't change the situation, so he put the old one back in, and is now puzzled ?
View 3 RepliesChevrolet - Montecarlo :: 2003 - Popping Sound Only When Turning Right
I found a steal of a car for my son, a 2003 Monte Carlo SS. The car had been hit slightly in the LF corner. The car needed front brakes, so I bought a package off Ebay that had rotors, pads, and wheel hubs. I replaced the LF wheel hub when we did the brakes and kept one for a spare since the RF felt good.
Shortly after replacing these parts, the car started to make a popping sound when you would turn right. The popping sound is much like an exhaust pipe dragging on the ground. We checked to make sure the was no contact with moving parts. After reading several forums, we decided to replace the LF hub with the spare we had. This did not fix the situation, so we put the first replacement LF hub onto the RF. Still no fix.
After this we decided to take the car to a empty parking lot and drove in circles trying to find the source of the noise. We discovered that the noise would go away if the car was put into neutral. We were still unable to locate the source of the noise.
So I decided to jack the car up and put it in gear and turn right. The noise did not occur with no load on the tires. However the u-joints on the axles were making some excessive noise, so I put in a new set of axles. Again this did not fix the noise. Now thinking the source must be in the differential.
Well two days after putting in new axles, the transmission went out. This will surely fix it, right? Well the mechanic that fixed the transmission said the pump had gone out, and it appeared the differential was creating shavings that caused this situation. GREAT WE FOUND THE SOURCE. Not so much!
Car still makes noise while turning right after replacing the transmission. I have driven myself crazy trying to find the source of this noise including riding in the engine compartment while my father drove in circles in the local high school parking lot.
Chevrolet - Montecarlo :: 2002 - Jerks Forward While Accelerating
What can cause a car to jerk forward while accelerating? Other symptoms include loss of HP and MPG. Recently had spark plugs and wires changed. Regular maintenance. I am about to see my mechanic and ask him to check the fuel pressure.
2002 Chevy Monte Carlo ss 100,000mi
Chevrolet - Montecarlo :: 1997 - Gear Shift Stuck?
How to fix a gear shift that tends to get stuck once in awhile. What about WD, and how would you apply it? I have a '97 Monte Carlo.
View 2 RepliesChevrolet - Montecarlo :: 1997 - Engine Randomly Has A Miss When Cruising
When cruising my engine randomly has a miss. If I step on it, not necessarily full throttle but some, the engine pulls fine no miss. I don't think it's ignition because it doesn't miss with increased throttle. I have looked at an analyzer and none of the sensors is showing a fault. I have put 20 tankfuls of fuel with cleaner through it after I put a new fuel pump and filter on and I only use Shell now for the last 10 fill ups. The miss is not a passive drop in rpm but more of a buck.
View 5 RepliesChevrolet - Montecarlo :: Jerking / Bucking During Acceleration - Low Fuel Pressure
My mechanic told me that the fuel pressure is about 5psi low. Could this cause jerking/bucking during acceleration?100,000mi SS
View 7 Replies