Chevrolet - Suburban :: 2001 - Constant ABS / Flashing Service Ride Control And Change Engine Oil Warning
Mar 22, 2011
I checked the cables, no corrosion and tight as a drum. I connected an OBD II computer to the plug under the dashboard and the computer replied that there were no trouble codes present. Is OBDII the proper code reader? none of these lights were on before I replaced the battery. now I have constant ABS, flashing Service ride control, change engine oil. The battery has not gone dead as of yet but the ampmeter is charging at about 16.5-17 volts. I disconnected the pos terminal while the vehicle was running and it continued to run even with the lights on.
View 2 Replies
Advertisement
My "service ride control" warning came on today. I have searched the forum and all I find is about air shocks. My 2002 3/4 ton Suburban has the electronic shocks, no air. Is there a common problem I should check? It is the first really cold day we have had, if that means anything.
View 9 Replies
I have a 2001 Suburban (chevy) 5.3 liter Vortec engine, auto trans 4 wheel drive, fully loaded. As of late I come out in the morning to find a dead battery. this happened before and I disconnected the fuse for the dvd player that was installed aftermarket. some times I have to hit my dashboard to get the dash lights to work, now they dont work at all. sometimes the ride control compressor runs for no apparent reason when the car is off. I replaced the battery 3 years ago and it seemed to solve the problem until now. I replaced the battery with an optima red top yesterday and now the electrical system is going haywire. the ABS light is flashing and the service ride control light is on, the fuel gauge is bouncing back and forth from full to empty. What should I do. I am a fair mechanic but electrical is not my forte.
View 3 Replies
I replaced the oil pressure switch on an '07 Suburban 5.3L because the oil pressure was showing low once the engine warmed up. That did nothing, then I found out about that little filter/screen under the sensor. I intended to remove and clean the filter then reinstall it. While I was pulling it out, I dropped it back behind the engine and couldn't find it. I checked online and found a few people in other forums that said to just remove the screen as a "fix", so I left it out and put the sensor back in, just to get the vehicle drivable. It started right up and ran fine for me, parked it, and a after sitting for a few hours it started popping while driving with the SES light flashing on the drive home.
Code P0300 was set, no cylinder specific misfire codes were present. I checked the misfire data and cylinder #6 showed tens of thousands of misfires, #5 showed several hundred, but I think it was just picking them up from #6 since #5 is right after #6 in the firing order. I disabled each injector with a scan tool, all changed the idle except #6, it did absolutely nothing. #6 fuel injector had good pulse to it, I connected a fuel pressure gauge and put power/ground to injectors #6 and #4, both dropped the same fuel pressure. I did the "cylinder deactivation" test on the scan tool for the four cylinders that have it, they all did the exact same thing - the engine bogged way down for a couple seconds and then died. Is that normal? I can't say I've ever seen a V8 engine die before when running on 6 or 7 cylinders. I checked compression on cylinder #6, it showed very low, almost zero, but I tried it a few times and it would show just a little compression at times... valves staying shut? I'm thinking when I opened the pressure relief valve on the gauge and the piston was near the bottom of the cylinder may be when it showed some compression. I also switched the coil/wire/plug from #6 to other cylinders and the miss did not follow.
Could having that screen out cause this problem? Having the engine die when deactivating the cylinders makes me wonder if maybe it's commanding all four at the same time, although the test shows each cylinder being controlled separately. Using a MODIS, not a TechII. I just got done putting in a new filter/screen to see if it would make any difference, and of course it didn't.
View 3 Replies
So I have two things I want to "fix" on my Passat:
1) Is there a way to turn off the "oil change" service warning message permanently? The dealer can do it but they want $46 every time And there is no way I will do that. I change the oil and filter myself.
2) When I lock my car the lights flash and the horn honks, is there a way to turn off the horn?
View 11 Replies
I have here a 2001 3/4 ton Suburban. It arrived last fall with 280K miles and a 6.0L V8 that was on its last leg (low to no oil pressure). I dropped in a 5.3L that I had handy, and had been happily driving it throughout the brutal Minnesota winter.
A couple months ago I noticed an issue developing. After a cold start, the engine would be severely lacking in torque for the first minute or so of driving. You could reach any RPM you wished, but the truck could barely accelerate. Once a minute or so had passed in this fashion, the issue would suddenly disappear... you'd be thrown back in your seat a bit if still attempting to accelerate, and the truck would take off. For the remainder of the trip, things would be fine.
Recently I went to drive the truck after it had sat for some weeks. It started fine, but the issue was now more persistent. When trying to accelerate, the gutlessness would continue for a good 15-20 seconds until finally and suddenly disappearing. Let off the gas, wait a moment, try to accelerate again, and it was the same thing all over again. Eventually I also noticed very obvious stumbling/missing when trying to get moving from a dead stop. Idle remained smooth.
The plugs and wires are only a few months old. The fuel filter is new. I checked for vacuum leaks (none that I could find). Fuel pressure is consistently around 50psi, even while the issue is happening.
The MIL was not on. I checked with my scantool, and found that P0101C was set, with P0101 pending. Visually examined the MAF harness and sensor; all looked fine. Swapped in a used working MAF; no change. (I suspect these codes may be due to the fact that I'm running a 5.3 with a stock, unmodified 6.0 PCM.)
My scantool is a Genisys running System 2.0. I'm by no means an expert with it, but I did know enough to try watching the miss counts while the symptom occurred. All cylinders seemed to be missing equally as much as the others, more or less.
Normally I'd be suspecting the fuel pump and/or associated wiring was going bad, but the pressure seems fine. What I might be missing?
View 10 Replies
So I just got my oil change and the "service now" warning did not turn off. Can I do that myself or not?
View 5 Replies
So I did my own oil change for the first time instead of taking it to a shop. Now I have the service warning indicator that comes on in the MFD every time I start the car. Is there any way to reset the interval warning indicator without a vag com or taking it to a dealer/ind. shop?
View 4 Replies
I was on the way back from the weekend trip and got a service engine soon light. I didn't notice any lack of power, rough idle or hard starting cold or hot. So we pushed on home. I checked the codes and it is the P1211.
Doing some research it seems the ICP is not as expected so I hooked up my phone with the Torque app and the IPR and ICP seem to be close to normal at idle and running. I din't see any high IPR %.
At idle the IPR was around 15.5 cold and 10.1 after a short run to the store and back when it warmed up a bit. ICP was around 690-720 cold and 470-490 when i got back.
Does that seem like normal readings? I cleared the codes and the CEL comes back on right away after starting the truck. I do have a TS performance chip that I will take out and see if that could be causing any problems. What else should I be looking into?
View 14 Replies
Well when it rains it pours. As I was picking up my truck from the dealer for the brake master cylinder issue I noticed some faults come up on the display as I got into my truck. It was a Hill Descent Control Fault and a Service AdvanceTrac warnings on the dash. I told the service write about them and had already cleared them thinking it was a fluke alert from the servicing they did. Well they have come back in and after some searching I hear that when we get these alerts the solution was Ford having to replace the entire steering rack??!!
View 5 Replies
How do I adjust the parking brake on my 2001 Suburban? It is a 2wd 1500 model.
View 3 Replies
2007 Chevy Suburban, 65K milesLet me start by saying I took this into to the dealer and they found nothing!
When I accelerate, I get a "flutter" in the engine. The best description of this flutter is that the RPMs go down about 200 or 300. I think it feels like it is sluggish when it accelerates. It is most obvious during the 35 - 60 MPH range, but you also see it when cruising at 70 MPH.
I tried adding some fuel treatment and ran some 93 octane through it to see if it was the fuel injectors, with no change in the behavior. No error messages or engine light is on. Regular oil changes and services (60K service, every 3K miles for oil change). Driving behavior has changed since I bought a Prius 3 months ago. It used to be driven 40 miles / day (+ long trips) and now is driven about 40 miles / week (+ long trips).
View 1 Replies
2002, Chevy, Suburban 1500, 4wd, 5.3L engine, 210,000 miles. Mass airflow sensor and both O2 sensors replaced last year in an effort to fix this problem. Original problem surfaced when the vehicle was shut down or running uphill and had about 1/2 tank of gas in hot weather. If stopped, the vehicle would not start until it had cooled down. Sometimes getting it onto level ground would be enough to get it running again. ( This accomplished by turning on the key and allowing the vehicle to roll back out of the parking place. ) If running down the road, getting to level ground after the stall, pulling to the shoulder and cooling the engine/waiting a few minutes and restarting the vehicle would work. This was before the above mentioned repairs.
Last weekend in 60 degree weather I was driving back from northern Michigan and as I headed up hill at 75 mph with the tank at 1/2 the vehicle did a high speed stall on me. Symptoms were: RPM showed 2000, but pushing down on the gas actually dropped the RPM no matter how feather-footed I was. This was tried several times. I turned on the 4 ways and moved toward the shoulder and at 50 mph finally got the thing to restart. The rest of the trip home was uneventful.
I had a 2001 Suburban with the same specs which did this same thing until a factory recall that got me a new fuel pump. I asked about the recall the last time my truck was in for service and they said it does not fall within the serial numbers for that recall. Fuel filter replaced about 9 months ago. Co-incidentally but not necessarily related is that my battery with less than 3 years of a 7 year warranty was draining itself in less than 2 days this last winter.
View 8 Replies
Well today I was happy go lucky on my way to work everything was going fine then all of a sudden this car in front of me slows down. Okay then I go to speed back up and my car was still crunk but I lose power I could not accelerate at all. So I had to coast to the side of the road and I put the car in park to see if it will allow me to accelerate in a different gear and when I do that.
The car shuts off then I go to crank it back up the first time and I got nothing then I wait a couple of seconds then try it again. It cranks up but still cant accelerate until I raise the engine then I can finally move. I was able to do about 65 mph to get to work but this happened two more times before I got back home that night. The car is a 2000 and has 220,000 miles on it.
I took the car to a part store to see why the service engine light was on. They told me it was a bad or faulty EGR valve but this was the first time the service engine light has flashed before.
View 13 Replies
2000 F250 V10 Auto/Rebuilt Tranny... This weekend, I noticed my truck wasn't shifting at lower RPMs like it has been. I'm not hitting much higher RPMs per shift then normal. Very soon after, I get a "Service Engine Soon" light and my "OD OFF" light on my shifter handle started flashing.
View 8 Replies
My engine revs up no matter if the thing is hot or cold when I come to a stop at a red light, SOMETIMES. Other times it will idle at 100 and then wants to idle around 1000 and has idled as high as 1200. I've been told EGR, TPS, Idle Control Motor, or Intake gaskets. I did have a code 22 which occurred after a friend unplugged the TPS and reconnected it, but no other codes or check engine lights. Tuned engine 2 weeks ago, but problem still persists. Where do I start and what equipment do I need. I am a professional diesel tech, but not so much with gas.
View 3 Replies
My Burb starts right up when the engine compartment is cold. Can barely touch the key and the thing fires right up.
Once engine compartment is hot (operating temp), I shut off the motor, let it sit for a few minutes and I get about 3-5 seconds of dry start each time I start it. It fires right up, runs great after that dry start period.
The dry-start behaves as if it's starved for fuel for those 3-5 seconds.
It's a K1500 with a stock 5.7l (350 ci). 180,000 miles and the entire drivetrain runs like a top. Only mod I've made is a K&N cold air intake.
Here's what I've done/changed recently (i.e. within the past 5k miles):
Fuel pump, OEM installed by dealer.Fuel filter.Ignition control module, BWD.Ignition coil, BWD.Crankshaft position sensor, GM OEM.Engine coolant temp sensor, BWD.Oxygen sensors (all four), GM OEM.Catalytic converter, replaced one of the two.Plug wires, BWD.Plugs, Delco OEM.Distributor cap and rotor, BWD.Cleaned ground connection (bolts to frame) for fuel pump.Alternator, new not reman.PCV valve.Battery.
Full diagnostics by a very qualified shop two weeks ago, no bleedback from injector spider, fuel pressure solid and holds perfectly. After 90 minutes of troubleshooting, the mechanics finally gave up.
One last thing with potential that I can think of is that I started running ethanol-free gas around the same time this issue surfaced. Not at the exact time, but at a relatively similar time. Gas mileage has increased by 40% and power increased, hard to blame "bad gas."
View 19 Replies
2001 Accent 1.6, A/T. Just replaced alternator myself. Checked and adjusted all three belts; all seem tight. Now I have a belt squeal. P/S fluid is full. When car starts there is no squeal. 15 seconds later chirp starts. A few seconds later squeal is constant and remains throughout entire ride - except when I make a turn. During any turn squeal goes away, then comes right back.
View 8 Replies
I have a 1992 Chevy S10 with 84,000K on it. It drives fine but when I get on the interstate and am driving 65mph for about 5-10 minutes the 'service engine soon' light comes on sometimes it takes longer. It only does it when I'm driving on the interstate and not if I'm just driving around town. It also doesnt turn on all the time but when it does come on it stays on until I turn the engine off.
View 1 Replies
Today when I was driving my car on the highway suddenly i saw the service engine soon warning, so many times i restarted the engine but its not working. After that I went to the service center and they said the code PO171, it might be oxygen sensory.
View 3 Replies
2001 01 1.8t... Hoping this isn't a bad ABS module. When I bought the car, I was told it was a bad wheel sensor in the drivers side. But, the funny part about this is its not on all the time, sometimes it doesn't even come on and the dash is normal.
View 3 Replies
